Denon DNRP-WRC Wired Remote for DN-F450/650R

124.62 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Availability: Available in 4-10 d. Available in 4-10 d. SKU: 134.037 Category:
The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder. The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness […]

 

Read more

The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder.

The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness red and green indicators located around the RECORD button, which show STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE. The two button control allows the recorder to be placed into record mode, create a new record mark and stop the recording process.

The DNRP-WRC is primarily for the simple control of audio recording in areas where conversations, discussions or conferences are taking place. The unit allows the DNF450R/F650R recorder to be placed out of sight to prevent media tampering or access to all the recorder controls.

  • Simple unobtrusive controller for the recording of audio in board/meeting rooms
  • Easy connection to Denon DN-F450R/F650R recorder serial (RS232) port
  • Provides bright visual indication of STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE
  • RECORD and STOP buttons allow simple control without the need to access the recorder
  • Ergonomic visually pleasing design with internal weight to prevent table slip
  • Ultra low power consumption, no need for additional power adaptor
  • Fully sealed label provides protection against drink spills

 

Weight 2.00 kg

Reviews

There are no reviews yet.

Be the first to review “Denon DNRP-WRC Wired Remote for DN-F450/650R”

Your email address will not be published. Required fields are marked *

Quick Comparison

Denon DNRP-WRC Wired Remote for DN-F450/650R removeTASCAM PS-PS5 Footswich Recorder Control removeTASCAM DP-32 SD 32-Track Digital Portastudio removeTASCAM DP-24 SD Digital recording system removeZOOM APH-2N Accessory Pack for H2N removeTOA D-2012C Remote Console Unit remove
NameDenon DNRP-WRC Wired Remote for DN-F450/650R removeTASCAM PS-PS5 Footswich Recorder Control removeTASCAM DP-32 SD 32-Track Digital Portastudio removeTASCAM DP-24 SD Digital recording system removeZOOM APH-2N Accessory Pack for H2N removeTOA D-2012C Remote Console Unit remove
Image
SKU134.037PS-PS5TAEM000555TAEM000544G30ZM00007D-2012C
Rating
Price124.62 incl. GR VAT 42.86 incl. GR VAT 625.00 incl. GR VAT 469.00 incl. GR VAT 38.00 incl. GR VAT 5,581.47 incl. GR VAT
Stock

Available on backorder

In stock

Available on backorder

Available on backorder

In stock

Available on backorder

AvailabilityAvailable on backorderIn stockAvailable on backorderAvailable on backorderIn stockAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder.

The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness red and green indicators located around the RECORD button, which show STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE. The two button control allows the recorder to be placed into record mode, create a new record mark and stop the recording process.

The DNRP-WRC is primarily for the simple control of audio recording in areas where conversations, discussions or conferences are taking place. The unit allows the DNF450R/F650R recorder to be placed out of sight to prevent media tampering or access to all the recorder controls.

  • Simple unobtrusive controller for the recording of audio in board/meeting rooms
  • Easy connection to Denon DN-F450R/F650R recorder serial (RS232) port
  • Provides bright visual indication of STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE
  • RECORD and STOP buttons allow simple control without the need to access the recorder
  • Ergonomic visually pleasing design with internal weight to prevent table slip
  • Ultra low power consumption, no need for additional power adaptor
  • Fully sealed label provides protection against drink spills

 


For users of just about any TASCAM multitrack, the RC-30P is a wonderful timesaver. Punching in on recordings by hand means you're not ready to play right away. The RC-30P lets you play straight through. While automated punch-ins available on some recorders are also helpful, most punches can be done with the simple and efficient precision of the RC-30P, saving you time.


Add 8 more ADAT optical inputs and outputs to your DM-3200 or DM-4800. Also works with older TASCAM gear such as the DM-24, DS-M71 and SX-1.The DP-32 is a home recording Portastudio with 32 tracks based on solid-state technology. The unit is equipped with colour LCD and channel strip controls to make recording simple so the user can stay creative. Up to eight tracks can be recorded at a time on a standard SD/SDHC memory card through its XLR and 6.3-mm combo jacks. Input processing like compression and limiting, an internal send effect with reverb, delay and chorus, guitar amp simulation and multi-effects for use with the instrument-level input as well as an external effects send are available during recording. For mixdown, the DP-32 offers 20 channel faders and 12 rotary controls for EQ, Pan and effects including reverb and chorus. During the mastering process, the material can be further optimized with EQ, compression and normalization. Once finished, songs can be written to CD with the built-in CD-RW drive or transferred to computer over USB to publish the songs on the Internet, for example. Main Features 32-track digital Portastudio 8 mono tracks, 12 stereo tracks (can also be used as mono tracks) Record up to 8 tracks at once with 44.1/48 kHz and 16/24-bit audio resolution Simultaneous playback of all 32 tracks Virtual tracks for alternate takes and undo Dedicated stereo master track Colour LC display and 12-encoder channel strip for simple operation Built-in 40-channel mixer Mix down your 32 playback tracks with eight input signals to the dedicated stereo master track Use the Bounce function to set tracks free by mixing multiple tracks to a single mono or stereo track Dedicated controls for EQ, pan and effect sends Solid-state recording to SD Card media for better shock resistance and reliability compared to hard drive recording 8 balanced microphone inputs on balanced combo XLR/jack connectors Switchable phantom power for 4 channels each One input switchable to instrument level for direct recording of a guitar or bass Unbalanced stereo output (RCA jacks) Balanced stereo monitor output (6.3-mm TRS jacks) Two unbalanced effect sends (6.3-mm TS jacks) Stereo headphones output (6.3-mm TRS jack) MIDI input and output for MMC, Control Change and MTC output Footswitch input (2.5-mm mini jack) for Tascam RC-3F (optional accessory) Input effects (Limiter, Compressor, Noise suppressor, Exciter) Guitar effects (Amp simulator, Reverb, Compressor, Chorus, Flanger, Phase shifter) Mixdown effects (Reverb, Delay, Stereo chorus) Mastering effect (Single/Multi-band stereo compressor, EQ, Noise shaping) Mark function (up to 99 location marks) Built-in chromatic tuner and metronome CD-RW drive for audio CD creation as well as file import and export USB 2.0 port for data backup/restore and file transfer with a computer Specifications Recording media and file systems Recording media        SD card (512 MB to 2 GB) SDHC card (4–32 GB) File system        SD card (512 MB to 2 GB): FAT16 SDHC card (4–32 GB): FAT32 Analogue audio inputs and outputs MIC/LINE INPUTS A–H, XLR (balanced) Connector        XLR-3-31 (1: GND, 2: HOT, 3: COLD) Input impedance        2.4 kOhm Nominal input level        –14 dBu Maximum input level        +2 dBu MIC/LINE INPUTS A–H, phone jack (balanced) Connector        6.3-mm TRS phone jack Input impedance        >22 kOhm or 1 MOhm (INPUT H, when LINE-GUITAR switch is set to GUITAR) Nominal input level        +4 dBu Maximum input level        +20 dBu STEREO OUT L/R connectors        RCA pin jack Nominal output level        –10 dBV Maximum output level        +6 dBV Output impedance        200 Ohm EFFECT SENDS 1/2 connectors        6.3-mm TS phone jack Nominal output level        –10 dBV Maximum output level        +6 dBV Output impedance        200 Ohm MONITOR OUT L/R connectors        6.3-mm TRS phone jack Nominal output level        –2 dBu Maximum output level        +14 dBu Output impedance        200 Ohm PHONES connector        6.3-mm TRS phone jack Maximum output power        70 mW + 70 mW or more (THD + N 0.1% or less, 32 Ohm load) Other inputs and outputs MIDI input (MIDI IN)        DIN 5 pin Format        Standard MIDI format MIDI output (MIDI OUT)        DIN 5 pin Format        Standard MIDI format USB connector        USB 4-pin mini-B type Format        Mass Storage Class USB 2.0 High Speed REMOTE connector        2.5-mm TRS jack Audio performance Frequency response        20 Hz to 20 kHz, +1/–1 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) Distortion        ≤0.01 % (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) S/N ratio        ≥90 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) Audio performance Frequency response        20 Hz to 20 kHz, +1/–1 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) Distortion        ≤0.01 % (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) S/N ratio        ≥90 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT) Operating system requirements Windows        Pentium 300 MHz or faster 128 MB or more memory Macintosh        Power PC, iMac, G3, G4 266 MHz or faster 64 MB or more memory Recommended USB port        USB 2.0 Recommended USB host controller        Intel chipset Supported operating systems        Windows XP, Windows Vista, Windows 7 Mac OS X 10.2 or later Power requirements and other specifications Power supply        AC adaptor (TASCAM PS-1225L) Power consumption        12 W (Phantom power on) Dimensions (Width x Height x Depth, excluding projections)        514 mm x 104 mm x 340 mm Weight        6.2 kg Operating temperature        5–35 °C Design and specifications subject to change without notice.

The DP-24SD Digital Portastudio is a 24-track workstation, allowing eight tracks of simltaneous recording. The built-in mixer includes everything you need for a professional-sounding mix, from EQ and reverb to amp simulation and multi-band mastering effects. The Digital Portastudio series creates finished productions without the need for a computer, instead using a simple-to-use control surface to keep you creative. 

For clear display of your mix, the DP-24SD has a large color LCD displaying tracks, meters, and effects parameters. A set of 12 encoders control EQ, effects sends, and panning. Built-in effects include compression, guitar amp modeling, delay, reverb, with a total of 10 effects processirs available during mixing. 

Eight XLR mic/line inputs each provide phantom power for condenser microphones, switchable in banks of four. One input includes an instrument-level impedence switch for direct input recording of guitar or bass. Balanced monitor outputs and effects sends are also provided on the rear panel. A USB output allows tracks and mixes recorded to your SD card to be transferred to a computer for CD burning or sharing online. 

For a complete music production on a desktop, there's no simpler choice than the DP-24SD.

DP-24SD SPECIFICATIONS
Recording Media SD (512MB – 2GB) / SDHC card (4GB – 32GB)
File System SD card:FAT16 / SDHC card:FAT32
INPUT A-H
 
XLR
 
Connector XLR-3-31(1:GND, 2:HOT, 3:COLD), Balanced
Input impedance 2.4k ohms
Nominal input level -14dBu
Maximum input level +2dBu
TRS
 
Connector 6.3mm(1/4“)TRS phone jack, Balanced
Input impedance 22k ohms or more
/ 1M ohms(when INPUT H, GUITAR selected)
Nominal input level +4dBu
Maximum input level +20dBu
STEREO OUT
 
Connector RCA pin-jack, Unbalanced
Output impedance 200 ohms
Nominal output level -10dBV
Maximum output level +6dBV
EFFECT SENDS  
Connector 6.3mm(1/4“)TS phone jack, Unbalanced
Output impedance 200 ohms
Nominal output level -10dBV
Maximum output level +6dBV
MONITOR OUT  
Connector 6.3mm(1/4“)TRS phone jack, Balanced
Output impedance 200 ohms
Nominal output level -2dBu
Maximum output level +14dBu
PHONES
 
Connector 6.3mm(1/4“)stereo phone jack
Maximum output level 70mW + 70mW (THD+N 0.1% or less, 32 ohms loaded)
USB  
Connector
USB Mini-B type 4-pin
Format USB2.0 High-Speed mass-storage class
REMOTE
 
Connector
2.5mm TRS jack
Power Dedicated AC adapter (TASCAM GPE248-120200-Z, included)
Power consumption 12W (when phantom power supplying)
Dimensions 514(W)×100.4(H)×336.9(D)mm / 20.2“(W)×4.1“(H)×13.4""(D)
Weight 6.2kg / 13.67 lb
Accessories AC adapter, 4GB SD card, warranty card, owner's manual

 

Audio performance
Frequency response 20Hz to 20kHz (+/-1dB, INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
S/N Ratio 90dB or greater (INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
THD 0.01% or less (INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)

 

Operating system requirements
Windows  
OS Windows XP, Windows Vista, Windows 7, Windows 8
CPU Pentium 300MHz or more
Memory 128MB or more
USB USB2.0
Macintosh  
OS Mac OS X Snow Leopard(V10.6), OS X Lion(V10.7), OS X Mountain Lion(V10.8), OS X Mavericks(V10.9)
CPU Power PC, iMAC, G3, G4 266MHz or more
Memory 64MB or more
USB USB2.0

 

The APH-2n optional accessory pack includes seven tools for use with the H2n. The remote control can be used to start, stop and pause recordings as well as to add marks. The other accessories in the pack are a windscreen that reduces wind and breath noise, a mic clip adapter for use with a mic stand, a tabletop tripod with extendable legs, a padded-shell case, an AC adapter and a USB cable.

The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.

 

Specification
* 0 dB = 0.775 V
Power Source 220 - 240 V AC
Power Consumption 18 W
Volume Adjustment 100 mm motorized fader x 12
Rotary encoder x 8
Line Input 1 channel (stereo)
Headphone Output Stereo 100 mW + 100 mW (32 Ω load)
Monitor Bus 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP)
LAN Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub)
Control RS-232C: D-sub connector (9 pins) for maintenance use
Finish Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate
Dimensions 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43)
Weight 6.6 kg (14.55 lb)
Accessory Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3
Option Console case: D-2012AS

 

Weight2.00 kg1.00 kg6.20 kg10.00 kg4.00 kg6.60 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 2.00 kg
Weight 1.00 kg
Weight 6.20 kg
Weight 10.00 kg
Weight 4.00 kg
Weight 6.60 kg