| Content | Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.
A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.
- 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
- 0.1dB resolution updated every 0.5 seconds
- Auto ranging or manual range selection
- ʽAʼ & ʽCʼ frequency weighting
- Fast or slow response filters
- 42mm LCD display with quasi-analogue bargraph and function Indicators
- Bargraph in 1dB steps updated every 40ms
- Max hold function to display the highest recorded value
- Min/max memory since power on or last reset
- Low battery indicator
- Auto power off
- Analogue output AC: 0.707 Vrms (at full scale)
- Supplied with battery
| With the PAN05, two microphone signals can be mixed down to one. Since decoupling occurs via the balanced resistor network, the PAN05 also lets phantom power "pass through“, useful for condenser microphones. However, due to the difference in sound and signal level, mixing dynamic and condenser mics should be avoided. Best results will be achieved using two identical mics.
SPECIFICATIONS:
- Input: 2 x XLR/f balanced
- Nominal impedance: 200 Ω
- Output 1 x XLR/m balanced
- Load impedance >200 Ω
- Symmetrically decoupled through resistors
- Total ohmic value: 200 ohms
- Typical attenuation: 6 dB
- Housing: metal casing 110 x 73 x 42 mm
| Non-Contact Laser Thermometer LCD Digital IR Infrared Thermometer GM400 Temperature Meter Gun Point -50~400 Degree
This infrared thermometer USES non-contact infrared sensing technology, the target of safety, preparation, fast, reliable measurement, is widely used in measuring the mechanical, chemical, ceramics, light industry, food, metallurgy, electric power, high temperature heat treatment and other industries, dangerous and difficult to close to the surface temperature measurement. Temperature measurement is widely used in the school laboratory and home.
Objects of any temperature greater than absolute zero radiation infrared energy, this energy to around at the speed of light transmission, infrared lens collects and gathers the infrared energy to the sensor, the sensor produces a low output voltage, the voltage is proportional to the temperature of the target object, voltage after processing for the temperature value.
- Not recommended for human use.
Main features:
1. Temperature range: -50 ℃ ~ 400 ℃ (-58 ℉ ~ 752 ℉)
2. Accuracy: ± 1.5 ° C (± 2.7 ° F) OR ± 1.5% ° C
3. ℃ / ℉ conversion selection function
4. Display resolution: 0.1 ℃ or 0.1 ℉
5. Working environment: 10 ℃ - ~ 40 ℃ (50 ℉ ~ 104 ℉), relative humidity: 10 ~ 90RH no condensation
6. Storage temperature: -10- ~ 40 ℃ (14 ℉ ~ 104 ℉)
7. Detection time: ≤ 0.8second
8. Distance coefficient ratio: 12: 1 (distance and measuring point size ratio)
9. Emissivity: Preset: 0.95
10. Power supply: 2 7 batteries (purchase, replace the battery more convenient)
11. Battery life of about 12 hours
12.LED backlight (easy to use at night)
13. Automatic shutdown function (about 10 seconds)
| Model |
INFRARED THERMOMETER-GM400 |
| Temperature range |
-50 ℃ ~ 400 ℃ (-58 ℉ ~ 752 ℉) |
| Accuracy |
± 1.5 ° C (± 2.7 ° F) OR ± 1.5% ° C |
| Display resolution: |
0.1 ℃ or 0.1 ℉ |
| Working environment |
10 ℃ - ~ 40 ℃ (50 ℉ ~ 104 ℉), relative humidity: 10 ~ 90RH no condensation |
| Storage temperature |
-10- ~ 40 ℃ (14 ℉ ~ 104 ℉) |
| Detection time |
≤ 0.8second |
| Distance coefficient ratio |
12: 1 (distance and measuring point size ratio) |
| Emissivity Preset: |
0.95 |
| Power supply |
2 7 batteries (purchase, replace the battery more convenient) |
| Battery life |
12 hours |
| LED |
LED backlight |
| Automatic shutdown function |
about 10 seconds |
|
ARTSOUND A8862 LASERGRIP THERMOMETER
Temperature range: -32 C - 550 C
Accuracy: 1,5%
Power supply: 9V
Weight: 258gr
| Overview:
This is an infrared digital forehead thermometer with high precision, which is hand-held and portable for easy use. Non-contact design reduces cross infection effectively, widely used for measuring body temperature.
Features:
High precision infrared sensor, stable and reliable, for safe use, ensures accurate measuring, small error.
Alarm temperature can be set and once exceeded, it will give out a beep sound. Also, it supports the Mute mode.
Humanized design, LCD screen display with high brightness backlight can clearly show the body temperature.
Aim at the forehead (3-5cm), press the measuring button, and the LCD display will show the currently measured temperature.
Automatic store 32 sets of measurement data, you can view the data of the previous measurement.
Short press the Function Setting button to switch between Body and Object temperature modes.
Compact design, lightweight and portable, comfortable grip handle, easy to carry, convenient to use.
Suitable for baby, kids, and adult use and can be widely used in school, office, and at home, etc.
Note: The battery is not included.
Specification:
Model: ZK-YK1028
Measuring Method: Non-Contact
Measuring Distance: 3cm-5cm
Unit of Measurement: Celsius(℃), Fahrenheit(°F)
Measuring Range: 32℃-42.9℃ (89.6°F-109.2°F)
Max. Allowable Error: ±0.3℃ within range 35℃-42℃
Display Resolution: 0.1℃/0.1°F
Operating Environment: 16℃-35℃ (60.8°F-95°F), Humidity≤85%
Transportation Storage Environment: -20℃-50℃ (-4°F-131°F), Humidity ≤90%
Power: DC 3V (2 AAA Batteries Not Included)
Backlight: Highlight Backlight
Automatic Shut-down: 30s
Item Size: 15.0 * 8.5 * 4.3cm / 5.90 * 3.34 * 1.69in
Item Weight: 105g / 3.70oz
Package Size: 17.0 * 10.5 * 4.8cm / 6.69 * 4.13 * 1.89in
Package Weight: 156g / 5.50oz
Package List:
1 * Thermometer
1 * User Manual (English)
| Details
The all metal DB DISPLAY MKII decibel display from American Audio is great for monitoring your sound volume. It also creates a great lightshow in your amp rack. Make sure your speakers stay in great shape by keeping those dBs under control through this monitoring system.
The LED display progresses from green through amber, to red. There are two different operating modes: Dot or Bar. A 5V power supply is included so you can get the unit plug in an running right away. The DB DISPLAY MKII is perfect a stage, church, club or bar install or for a mobile entertainer.
Specifications
• Designed to set in an amp rack to view your decibel level
• Creates a great light show in your amp rack
• Display progresses from green through amber to red
• Sensitivity adjustment on both left and right channels
• 2 separate modes: dot and bar
• Includes 5V power supply
• Line Inputs: Left & Right RCA / Left & Right XLR
• Line Outputs: Left & Right RCA / Left & Right XLR
• Voltage Operation: DC 5V, 500mA Power Supply included
• Dimensions: (LxWxH): 19” x 1.75” x 1.75” / 44.5mm x 483mm x 44.5mm
• Weight: 2.5 lbs. / 1.25kg. |
Reviews
There are no reviews yet.