DRAWMER 1968 MKII Dual Channel Tube Compressor

1968 MkII - Dual Channel Tube Compressor

Blend valves and FETs for quality compression. The 1968 MkII is a 1U Tube/FET ‘stereo bus’ compressor which by design delivers a transparent ‘open’ sound even during periods of heavy compression. 

The original Drawmer 1960 used a tube stage at the front of the compressor, whilst the 1968 MkII utilisies a J-FET (Field Effect Transistor) gain reduction circuit that operates faster than an opto-isolator. The compressor uses a 12AX7 tube makeup gain amplifier where you can add, with the Output Gain control, up to 20 dB of additional gain. The need for a ratio control has been removed as the compressor operates on the soft knee principle where the onset of compression is progressive.

The 1968 MkII expands attack times to six choices: 2, 9, 15, 25, 30 and 50 ms. Release times come in three fixed times (100ms, 500 ms and 1 second) and three program-dependent choices--200 ms to 2 sec, 500 ms to 5 sec and 1 to 10 seconds--all program-dependent and automatic. 

The 1968 MkII provides full sidechain access for connecting an external equalizer for vocal stressing or de-essing.

Featured on both channels is a switchable ‘BIG’ and ‘BIGGER’ mode which applies less processing to the fundamental low frequency but still disciplines the upward associated harmonics which if untamed can result in a ‘boomy’ or ‘boxy’ sound. The result - a solid bottom end with enhanced sub-bass and a smoother, wider frequency response overall. This lets the operator use more compression on an overall mix with less pumping action caused by a kick and/or bass instrument.

The outputs of Channels 1 and 2 are monitored on two yellow illuminated VU meters - with a red warning glow to signify ‘approaching clipping’. A three-position switch adjusts the meters to show either normal output level, gain reduction or VU +10dB mode, which re-scales the meter for users working at ‘hot’ output levels.

An output switch selects normal compressor output, hard-wired bypass and sidechain listen.

 The key features are as follows:

• 2 Channel Tube/FET Compressor.
• 2 soft-knee compressors with variable threshold, attack, release and output gain.
• Switchable BIG and BIGGER control on each channel.
• Dual mono or true stereo link operation.
• Side chain access and side chain listen facility.
• VU metering of gain reduction and output levels.
• Switchable +10dB mode on VU re-scales the meter for users working at ‘hot’ output levels.
• VU red warning glow to signify ‘approaching clipping’.
• Balanced +4dB XLR in/outs.

Due to customer demand we have introduced new features to the 1968 MkII:

• Expanded the BIG to include BIGGER - setting the filters to 75Hz and 150Hz.
• Added internal jumpers that can be configured to remove the soft clip section.
• Added internal jumpers to make the output hotter by 6dB, if required.
• Improvement have been made to the PSU to lower the noise floor.

Innovation

The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
 
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
 
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
 
T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.
 

GENERAL DATA
Power Supply 220 / 110V 25 VA
Dimension 434x351x44mm (1 rack unit)
Weight » 4 Kg
MEETING INTERFACE IN / OUT
Connector DB 9 female
Nominal in / out audio level 0 dBm
Input impedance 600 W / 10 KW (selectable)
Output impedance 100 W
* nominal line level: - 6 dBm
** it can vary depending on characteristics of telephone line
All measurements are intended at 1 kHz.
AUDIO PROGRAM IN / OUT
Connectors XLR, electr. balanced
Input impedance 600 W / 10K W (selectable)
Output level * - ¥ ¸ + 16 dBm
Output impedance 100 W
Noise on Receive output 2-Wire separation £ 25 dB**
4-Wire separation £ 70 dB
2-WIRE SECTION
Connector RJ11
Nominal input level - 6 dBm
Nominal output level - 6 dBm
Compensation mode Electronic, transf. decoupled
Impedance 600 W
4-WIRE SECTION
Connector Terminal block
Impedance 600 W
Nominal TX level 0 dBm
Nominal RX level 0 dBm

The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative. 
 
FEATURES:

4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty 

OPTIMOD-FM 5500 puts coveted five-band and two-band OPTIMOD processing into a single rack unit package and brings it to you at the most affordable price ever.

Quality sound is what 5500 is all about-sound that attracts audiences by providing a polished, professional presentation regardless of format and source material. Exceptional versatility allows you to adjust the processor's audio texture to brand your audio, knowing that the resulting signature sound will remain consistent, cut-to-cut and source-to-source. Branding builds businesses and no other processors have the consistency to brand your sound like OPTIMOD.

With the 5500, your signature sound is just a preset away. An easy, one-knob Less/More adjustment allows you to customize any factory preset, trading cleanliness against processing artifacts according to the requirements of your market and competitive environment. Full Control gives you the versatility to customize your audio further. And, if you're a hard-core processing expert, you can explore Advanced Control to tweak presets at the same level as Orban's factory programmers. This versatility makes the 5500 a superb choice for any format. Its five-band processing is ideal for any pop music format (even the most competitive and aggressive CHR), while phase-linear two-band processing yields ultratransparent sound for classical, classic jazz, and fine arts formats. Regardless of your choice, 5500's optimized technology ensures unusually high average modulation and coverage for a given level of subjective quality. Unlike many lesser processors, the 5500 handles speech particularly well. It's always clean, even when you process for loudness.

If you're concerned about latency because you need to feed live talent headphones off air, be assured that the 5500's ultra-low-latency (5 ms delay) processing will keep the most finicky talent happy. Or use optimum latency (15 ms delay) processing for the most competitive sound with delay that's still low enough to satisfy most any talent.

The 5500 can also be used as a superb stand-alone stereo encoder with latency as low as 2 ms and full overshoot limiting in both the left/right and composite baseband domains.

When used in this mode, the 5500 must be driven (usually via an STL) by a full-featured FM audio processor (like Orban's 8600) that incorporates pre-emphasis aware HF limiting and peak control. In both modes, the 5500's stereo encoder helps deliver a transmitted signal that's always immaculately clean and perfectly peak limited, with full spectral protection of subcarriers and RDS/RBDS regardless of the amount of composite limiting.

It is the ideal choice for network broadcasters who process with Orban's flagship OPTIMOD-FM 8600 at the network origination point and who need a processor at every transmitter to eliminate STL overshoots (using the 5500's stand-alone stereo encoder mode) and/or to process local insertions while also eliminating network STL overshoots (using the 5500's audio processor / stereo encoder mode). Moreover, the 5500's two modes make it easy for large government and network broadcasters to manage its inventory of spares because any 5500 can be used as a stereo encoder with or without audio processing.

Available in both modes, the built-in, defeat-able ITU-BS412 multiplex power controller allows the 5500's output to meet even the most stringent European government regulations.

A 10 MHz frequency reference input allows the stereo pilot tone frequency to be locked to GPS or another high-accuracy frequency standard. This improves the performance of single-frequency networks in areas where coverage of the transmitters overlaps.

The 5500's built-in stereo encoder, AES/EBU digital inputs and outputs, and analog I/O permit hasslefree interfacing to any broadcast plant, whether the 5500 is located at the studio or the transmitter. Tight band limiting to 15 kHz means you can use any uncompressed digital STL to pass 5500- processed audio from studio to transmitter without compromising on-air loudness - there's no need to use STL's having 44.1 or 48 kHz sample-rate.

The stereo encoder's stereo sub-channel modulator can operate in normal double sideband mode and in an experimental compatible single sideband mode (SSB/VSB) that is offered to enable users to compare and assess the two modes.

Analog Fallback to Digital control that allows Silence Sense to switch the active input from Analog to Digital if silence is detected in the analog input signal but not on the digital input signal. This function works vice versa as well on both analog and digital AES input. The silence sense parameters apply to both simultaneously and both detectors are available to drive the 5500's tally outputs and sending SNMP Traps/Alerts.

If you want to locate the 5500 away from the studio, you'll be pleased by its three separate remote control ports - GPI contact closures, RS232 serial and built-in Ethernet for TCP/IP networks. The serial and Ethernet ports are supported by the supplied 5500 PC Remote Control application. This Windows® 2000/XP/Vista/7/8 application allows you to do even more with the 5500 than you can do through its front panel, making remote control a pleasure.

5500 PC Remote software allows you to access all 5500 features and allows you to archive and restore presets, automation lists, and system setups (containing I/O levels, digital word lengths, GPI functional assignments, etc.)

Built-in clock-based automation lets you automatically day-part the processing. You can control many other 5500 operating parameters too.

The 5500's feature set fully exploits the processor's DSP and computer-based control architecture. To ensure absolute accuracy, you can automatically synchronize the clock to an Internet timeserver. It has a cool-running, energy-efficient switching power supply and uses the latest dual-core DSP chip technology from Freescale Semiconductor.