The introduction of the Drawmer DL241 Dual Channel \’Auto-Compressor\’ highlights the beginning of a new generation of dynamic processors which set new standards of sonic excellence. Its combination of features, displays and well designed control functions make it an outstanding product for a vast range of broadcast, sound reinforcement, and recording applications. The DL241 \’Auto-Compressor\’ […]
The introduction of the Drawmer DL241 Dual Channel \’Auto-Compressor\’ highlights the beginning of a new generation of dynamic processors which set new standards of sonic excellence. Its combination of features, displays and well designed control functions make it an outstanding product for a vast range of broadcast, sound reinforcement, and recording applications. The DL241 \’Auto-Compressor\’ incorporates many automatic functions allowing the engineer to achieve optimum results in the minimum set up time but does not compromise skilled users with limited controls. Its sophisticated design produces a smooth, transparent and warm sonic performance.
Facilities available on the DL241 include:
Expander/Gate : Drawmer\’s unique “Programmed Adaptive Expansion” circuitry allows effective \’single control operation\’ producing a fast smooth response and eliminating \’chatter\’ on or around threshold. This design differs from that of conventional Expanders in that the Expansion Ratio, Hold Attack and Release continually adapt themselves to the dynamics of the incoming signal. The Expander/Gate provides 80dB range and variable threshold from +20dB to 70dB with an OFF position. Switching is provided for \’Fast\’ or \’Slow\’ release characteristics. The \’Fast\’ mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \’Slow\’ mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Compressor : A full Auto Attack/Release Compressor with variable Threshold and Ratio successfully combines the smoothness of the \’Soft Knee\’ principle with the precision of a \’Ratio\’ control. The advantage of this combination is that instead of the onset of compression being sudden at the threshold point the ratio increases over a 10dB input level range until it reaches the ratio set on the front panel control, thus achieving a more natural sounding compression. Selectable manual or fully automatic Attack and Release times dramatically extend the application range and user scope of the DL241. Selecting the \’Auto\’ mode removes the need for manual adjustment and is particularly valuable when the program being treated does not have predictable or consistent dynamics, often the case when processing a complete mix or a virtuoso bass guitar performance. Under manual control the wide range of adjustment available gives the user the ability to create dynamic effects as well as normal compression.
Peak Level. \’Zero Response Time\’, \’Zero Overshoot\’ circuitry : This provides an absolute limit to the peak level of the output signal, adjustable from OdB to +16dB above system level. When set to the required level, any excessive peaks will be stopped and the gain momentarily decreased if necessary. The \’Zero Response Time\’ is essential to avoid unpleasant distortion when mastering for CD or sending any signal to digital equipment. \’Zero Response Time\’ means that the DL241 provides complete protection from even the fastest and shortest signal \’spikes\’ (overloads), making the unit also ideally suited for speaker system protection in sound reinforcement applications.
Metering : Comprehensive bar graph displays give \’at a glance\’ indications of gain reduction, and output signal level Gain reduction from 1dB to -30dB is shown simultaneously with signal level from -20dB to +15dB Other single LEDs indicate function status of Gating Acton, Auto Mode, Bypass, Peak Limiting, Stereo Linking, and Power On.
Stereo Link : When processing stereo signals, linking should be used to prevent image shifting. This facility ties both channels together. Using channel 1 (left) as the master channel removes the need to duplicate control settings for both channels.
Bypass : A fully balanced hard-wire bypass connects the input directly to the output allowing signal to pass through the unit with no power applied. In bypass the VU level meter displays the Input signal.
Operating Level : The operating level of the DL241 can be instantly switched, independently on each channel, for either +4dBu or -10dBu operation using a rear panel push switch.
Input/Output : The DL241 is available with either XLR connections and fully balanced inputs and outputs, or with stereo jack (TRS) connections, fully balanced inputs and single ended outputs.
Weight
3.00 kg
Reviews
There are no reviews yet.
Be the first to review “DRAWMER DL241 XLR- Auto Compressor” Cancel reply
The introduction of the Drawmer DL241 Dual Channel \'Auto-Compressor\' highlights the beginning of a new generation of dynamic processors which set new standards of sonic excellence. Its combination of features, displays and well designed control functions make it an outstanding product for a vast range of broadcast, sound reinforcement, and recording applications. The DL241 \'Auto-Compressor\' incorporates many automatic functions allowing the engineer to achieve optimum results in the minimum set up time but does not compromise skilled users with limited controls. Its sophisticated design produces a smooth, transparent and warm sonic performance.
Facilities available on the DL241 include:
Expander/Gate : Drawmer\'s unique "Programmed Adaptive Expansion" circuitry allows effective \'single control operation\' producing a fast smooth response and eliminating \'chatter\' on or around threshold. This design differs from that of conventional Expanders in that the Expansion Ratio, Hold Attack and Release continually adapt themselves to the dynamics of the incoming signal. The Expander/Gate provides 80dB range and variable threshold from +20dB to 70dB with an OFF position. Switching is provided for \'Fast\' or \'Slow\' release characteristics. The \'Fast\' mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \'Slow\' mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Compressor : A full Auto Attack/Release Compressor with variable Threshold and Ratio successfully combines the smoothness of the \'Soft Knee\' principle with the precision of a \'Ratio\' control. The advantage of this combination is that instead of the onset of compression being sudden at the threshold point the ratio increases over a 10dB input level range until it reaches the ratio set on the front panel control, thus achieving a more natural sounding compression. Selectable manual or fully automatic Attack and Release times dramatically extend the application range and user scope of the DL241. Selecting the \'Auto\' mode removes the need for manual adjustment and is particularly valuable when the program being treated does not have predictable or consistent dynamics, often the case when processing a complete mix or a virtuoso bass guitar performance. Under manual control the wide range of adjustment available gives the user the ability to create dynamic effects as well as normal compression.
Peak Level. \'Zero Response Time\', \'Zero Overshoot\' circuitry : This provides an absolute limit to the peak level of the output signal, adjustable from OdB to +16dB above system level. When set to the required level, any excessive peaks will be stopped and the gain momentarily decreased if necessary. The \'Zero Response Time\' is essential to avoid unpleasant distortion when mastering for CD or sending any signal to digital equipment. \'Zero Response Time\' means that the DL241 provides complete protection from even the fastest and shortest signal \'spikes\' (overloads), making the unit also ideally suited for speaker system protection in sound reinforcement applications.
Metering : Comprehensive bar graph displays give \'at a glance\' indications of gain reduction, and output signal level Gain reduction from 1dB to -30dB is shown simultaneously with signal level from -20dB to +15dB Other single LEDs indicate function status of Gating Acton, Auto Mode, Bypass, Peak Limiting, Stereo Linking, and Power On.
Stereo Link : When processing stereo signals, linking should be used to prevent image shifting. This facility ties both channels together. Using channel 1 (left) as the master channel removes the need to duplicate control settings for both channels.
Bypass : A fully balanced hard-wire bypass connects the input directly to the output allowing signal to pass through the unit with no power applied. In bypass the VU level meter displays the Input signal.
Operating Level : The operating level of the DL241 can be instantly switched, independently on each channel, for either +4dBu or -10dBu operation using a rear panel push switch.
Input/Output : The DL241 is available with either XLR connections and fully balanced inputs and outputs, or with stereo jack (TRS) connections, fully balanced inputs and single ended outputs.
In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.
The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.
All four channels have the following controls:
Threshold - allows you to set the level at which the compressor starts affecting the gain
OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.
Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.
Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.
Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.
Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.
PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.
Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.
All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.
Four independent channels of operation, stereo linkable in two pairs
PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
Independent Threshold and ratio controls
Switchable OverEasy® or Hard Knee compression
Classic dbx® compression
Differentially balanced gold-plated XLR and 1/4" inputs and outputs
True RMS level detection
Precision metering of input level, output level, and gain reduction
Dual True stereo or quad mono operation
Switchable +4dBu or -10dBV operation per channel
Input Connectors
XLR and 1/4" TRS (Pin 2 and tip hot)
Input Type
Electronically balanced/unbalanced, RF filtered
Input Impedance
Balanced > 40 kOhm, unbalanced >20 kOhm
Max Input
> +22 dBu balanced or unbalanced
CMRR
Typically >50 dB at 1 kHz
Output Connectors
XLR and 1/4" TRS (Pin 2 and tip hot)
Output Type
Servo-balanced/unbalanced, RF filtered
Output Impedance
Balanced 30 Ohm, unbalanced 15 Ohm
Max Output
> +22 dBm balanced, > +20 dBm unbalanced
Bandwidth
20 Hz to 20 kHz, +0/-0.5 dB
Frequency Response
0.35 Hz to 90kHz, +0/-3 dB
Noise
Dynamic Range
> 118 dB, unweighted
THD+Noise
>0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
IMD
Interchannel Crosstalk
Stereo Coupling
True RMS Power Summing
Compressor Threshold Range
-40 dBu to +20 dBu
Compressor Ratio
1:1 to infinity:1
Compressor Threshold Characteristic
Selectable OverEasy® or hard knee
Compressor Attack/Release Characteristic
AutoDynamic™
Compressor Attack Time
Program-dependent
Compressor Release Time
Program-dependent
Compressor Output Gain
-20 to +20 dB
Limiter Threshold Range
0 dBu to +24 dBu (off)
Limiter Ratio
infinity:1
Limiter Type
PeakStopPlus® two-stage limiter
Limiter Stage 1
PeakStop® brickwall limiter
Limiter Stage 1 Attack Time
Zero
Limiter Stage 1 Release Time
Zero
Limiter Stage 2
Predictive intelligent program limiter
Limiter Stage 2 Attack Time
Program-dependent
Limiter Stage 2 Release Time
Program-dependent
OverEasy® Switch
Activates the OverEasy compression function
I/O Meter Switch
Switches between monitoring input and output levels on the Input/Output Level meter
Bypass Switch
Activates the direct input-to-output hard-wire bypass
Operating Level Switch
(rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels
ST Link Switch
Links channels in stereo pairs. Channels One and Three become the master channels
Gain Reduction Meter
8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB
I/O Meter
8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu
PeakStop™ Indicator
1 LED to indicate PeakStop™ limiting
Function Switches
LED indicator for each front-panel switch
Output Transformer Options
Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx
Operating Voltage
Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
Power Consumption
20 Watts
Fuse
100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
Power Connector
IEC receptacle
Dimensions
1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm)
Unit Weight
5.2 lbs. (2.4 kg)
Shipping Weight
7.6 lbs. (3.5 kg)
Product Features:
Ultra-high resolution 24-bit/96 kHz mastering processor featuring 32/40-bit floating-point DSP technology Audiophile 24-bit/96 kHz A/D- and D/A converters offering 113 dB dynamic range 4 concurrently selectable EQ modules (31-band graphic EQ, 10-band parametric EQ, Feedback Destroyer plus 3 Dynamic EQs per stereo channel) Ultra-high resolution 61-band real-time FFT analyzer with additional auto EQ function for room and loudspeaker equalization Unique VPQ (Virtual Paragraphic EQ) option allows parametric control of graphic EQs State-of-the-art compressor/expander with peak limiter per stereo channel, additional stereo imager and stereo delay for delay line applications Multi-functional level meters (peak/RMS, VU and SPL meter with dBA/dBC weighting via RTA/Mic input) 64 user memories for complete setups and/or individual module configurations Separate mic/line input with phantom power for RTA and Auto-EQ applications Balanced inputs and servo-balanced outputs with gold-plated XLR connectors, stereo aux output, AES/EBU and S/PDIF inputs and outputs (XLR and optical) Professional Wordclock input and MIDI connections for full remote control, preset dumps and system updates Open architecture allowing future software updates via MIDI "Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving High-quality components and exceptionally rugged construction ensure long life Conceived and designed by BEHRINGER Germany
Psychoacoustic Bass Enhancement Unit with Renaissance Compressor, MaxxBass, and L2
Bass Boost for Live Sound, Broadcast, Mastering & Post Production
They say that in electronics there's no new technology - the only changes
will be in size and applications. Things will simply keep getting smaller
while doing more. This is certainly true in music (just think about what an
iPod can do), but as we design smaller playback systems with small speakers,
there are also some tradeoffs, particularly in music. Clever cabinet designs and
high-excursion drivers can get you only so far. Any audio engineer trying to extract
bass from real-world components must eventually face the laws of physics:
All things being equal, small boxes and speaker cones can't move enough air
to produce a room-shaking low end. When working with systems tiny enough to
toss in a shoulder bag, the challenge is even more formidable. Interestingly enough,
Waves MaxxBCL has a new solution to this problem using a very old concept.
Waves MaxxBCL at a Glance:
MaxxBass? Bass Enhancement adds deep bass sound without adding bass frequencies
Waves Renaissance Compressor
L2 Ultramaximizer Peak Limiter
24-bit/96kHz resolution with 48-bit, double-precision processing
Supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced line-level analog signals
MaxxBass Bass Enhancement
Waves' patented algorithm adds stunning bass sound without adding bass frequencies,
delivering a bigger bottom end. MaxxBass? allows your audience to hear bass frequencies
lower than physically present by applying psychoacoustic principles: Even though we
can hear a bass guitar from a small speaker, we don't actually hear the fundamental
frequency because the speaker can't produce a pitch that low. Instead, we hear the
harmonics that the speaker can produce, and this causes the brain to create the "missing
fundamental." MaxxBass? takes this well-known psychoacoustic phenomenon to the
maximum, giving you the ability to extend the perceived frequency response of a system
about two octaves below its physical limitation.
To accomplish this, the signal is split: high frequencies are passed to the output (to be
added back to the bass). The bass signal is analyzed and a specific series of upper
harmonics are created. Because the dynamics of the original bass are duplicated in these
harmonics, the result is the most natural sounding bass enhancement available. The
MaxxBass? harmonics and the original bass can be mixed in any proportion at the output.
To provide more control, a high-pass filter can be switched in, allowing the harmonics only to
be passed along as an "image" of the original bass frequencies, which is useful when working
with a system with known low-frequency limitations to avoid over-excursion of the speaker drivers.
Renaissance Compressor
Designed to provide the classic warm sound of analog compressors, the legendary
Renaissance Compressor controls dynamics with studio-style warmth that flatters
full mixes, vocals, or instruments. Controls include selection of vintage-style Opto
or modern Electro compression, and threshold, ratio, and attack controls. Waves
ARC? (Automatic Release Control) algorithm dynamically optimizes the compressor's
release value for a wide-ranging input. ARC? reacts much the way a human ear
expects, and can produce increased RMS level with greater clarity.
In general, the release is faster for peak transients and slower for the overall RMS
level. The ARC? system varies the release time to fit the ear's expectations while
increasing RMS, and without creating distracting artifacts. In this way, the
Renaissance Compressor can serve as a leveler plus a fast compressor simultaneously.
L2 Ultramaximizer Peak Limiter
Heard on countless hit records and soundtracks, the L2 Ultramaximizer puts sound
up-front with breathtaking transparency. The L2 is capable of a very fast, overshoot-free
response. Once the limiter threshold has been set, you can define the actual peak level
that the processed signal will reach. Once set, limiting and level re-scaling becomes a
one-shot process. The L2 can significantly increase the average signal level without
introducing any audible side effects. Yet there is plenty of range to recreate "vintage"
effects such as level pumping or severely limited dynamic range if you like.
Pristine Sound Quality
The MaxxBCL offers 96kHz, 24-bit resolution with a 48-bit, double precision internal
processing path and a dynamic range of ~125dB. The totally passive analog input
path to the ADC uses Jensen transformers, while the output path also features Jensen
analog output transformers. The unit is galvanic-isolated, which prevents ground loops
and allows it to operate in electrically unstable environments. Waves MaxxBCL combines
the highest quality converters available with unequalled processing algorithms to offer you
astonishing new power in bass enhancement, dynamics processing, and format conversion
(analog-to-digital, digital-to-analog, and digital re-quantization).
Versatile Connections
The MaxxBCL supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced
line-level analog signals. MaxxBCL features a unique set of input and output trim settings:
analog input headroom can be set from 9dB above 0dBu to 24dB in six precise steps
(using the rear-panel selectors). Analog output level is similarly set with a separate
rear-panel trim pot offering you the ability to connect between devices with a wide range
of input and output levels.
Waves MaxxBCL Features:
User Interface:
Clear backlit displays, meters, and buttons are visible in all lighting conditions
THD + Noise: ? 0.0006 % @ 1kHz @ -1dBFS
Precision metering with resettable peak hold options (2 sec, infinite)
Accurate, wide-range metering covering 90dB for input and output
and 12dB for compressor and limiter attenuation
Quick access independent bypass on each processing block
Tactile feedback knobs
Four easy store/recall user presets
Input / Output:
Analog, AES/EBU, S/PDIF
Independent rear-panel input and output headroom calibration in six steps
(+9, 12, 15, 18, 20, and 24 dBu)
Passive analog inputs to the A-to-D converters using Jensen analog input transformers
Jensen analog output transformers
High-performance IDR dithering to 16- or 24-bit output
Precise input level setting using 1% resistor networks
Processing:
48-bit end-to-end internal processing path
Switchable compressor/MaxxBass? order
MaxxBass:
Adjustable processor frequency from 25 to 120Hz
Adjustable harmonic mix percentage from 0 to 100%
High-pass Filter "harmonics only" option
Compressor:
Opto/Electro mode selection
Threshold (0-60dB), Ratio (1:1-12:1), and Attack (0.5, 1, 2, 5, 10, 20, and 50 ms) controls
Proprietary ARC? Automatic Release Control
Automatic gain makeup
Limiter:
Overshoot-free look-ahead processing
Adjustable Threshold (0-18dB)
Adjustable Output Ceiling (0-18dBFS)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.