| Content | The MX30 Pro Gated/Comp/Limiter is a low cost professional quality dynamics processor. Drawing on our many years experience in professional audio we have developed a series of lower-cost Drawmer dynamic signal processors, the MX Pro range. Aimed at the musician, project studio and live performer, who is determined not to compromise on quality, but have to work to a tighter budget.
By using circuit elements drawn from existing top-of-the-line Drawmer products and by simplifying the control systems where possible, the MX Pro range is no less sophisticated than our other units, despite the price tag. As a result the inexperienced user gains the benefits of Drawmer quality and performance, combined with lower cost and simplicity of operation.
Operational control is split into three sections:- Gate, Compressor, Output:
Programme Adaptive’ Gate
Used to remove unwanted noise below a pre-set level, each channel consists of a variable Threshold Gate incorporating Drawmer’s ‘Programme Adaptive’ circuitry. Although quick and simple to operate, the gate’s auto-circuitry continually optimises such parameters as Attack, Hold, Ratio and Release, completely eliminating ‘chatter’ when the signal is fluctuating on or around Threshold. Two LEDs show when the signal is ‘above’ or ‘below’ Threshold and a push button switch allows additional control of Release time. This design approach also retains all ‘leading edge’ information making the gate ideal for ‘cleaning up’ vocals or retaining the ‘punch’ on gated drums. Switching is provided for \'Fast\' or \'Slow\' release characteristics. The \'Fast\' mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \'Slow\' mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Soft Knee ‘Auto Compressor’
The gate is followed by a variable Threshold, variable Ratio, soft knee compressor with fully automatic Attack and Release. Large transients are controlled instantly whilst small signal variations are treated gently, retaining as much ‘life’ as possible and without generating unpredictable side effects. the MX30 Pro handles all compression levels with ease and displays the amount of compression on a high resolution Gain Reduction bargraph meter.
Output
The Gain control is used to compensate for the amount of compression and brings the signal to the required output level as displayed by the output bargraph meter. A variable Threshold ‘zero overshoot’ limiter, essential for avoiding distortion when mastering to digital or speaker protection in a ‘live’ situation, adds the final polish to the signal by keeping control over signal peaks. The Limit threshold provides an absolute maximum peak level which no signal can pass. Fast transients are clipped instantly whilst more sustained peaks are dealt with by applying Gain Reduction, indicated by a single LED.
Gate Threshold:
This control sets the level below which gating takes place and may be set anywhere in the range of -70dB to +20dB. A green LED illuminates to show when the signal is above threshold (i.e. gate open) and a red LED illuminates when the signal is below Threshold (i.e. gate closed).
Release: Either a Fast or Slow auto release contour may be selected depending on the material being processed. An LED indicates when Slow release status is engaged. Percussive material with little or no reverb is generally treated using the Fast release setting, whereas with slow decays or a significant amount of added reverb will usually respond better to the Slow release setting.
Compressor Threshold: This determines the input level above which gain reduction will be applied and may be set anywhere in the range of -40dB to +20dB. Soft Knee compression takes place for signals exceeding the threshold level by up to 10dB above which level, conventional ‘ratio’ compression is applied.
Gain Reduction Bargraph Meter: A nine segment LED bargraph meter continuously monitors the gain reduction applied by the compressor over a range of 0dB to 30dB.
Ratio: Sets the final compression ratio that will be applied once the 10dB soft knee region is exceeded. The ratio may be continuously adjusted from 1.2:1 to infinity:1 allowing the possibility of true hard limiting. The higher the ratio setting the more compression takes place (eg. A ratio of 8:1 means that an 8dB increase in volume at the input will appear as a 1dB increase in volume at the output).
Stereo Link: The unit can function as two independent gated/compressor/limiters or when ‘link’ mode is engaged for stereo use Channel 1 becomes the master, automatically duplicating its parameters across to Channel 2. In this mode the same degree of gain reduction is applied to both audio channels to prevent image shifting.
Output Gain: The output level may be attenuated or amplified by up to 20dB to compensate for level changes caused by compression. This control comes directly before the Peak Limiter detector and this fact should be taken into account when setting the Peak Limiter threshold.
Peak Limit: This control sets an absolute limit that the output signal will not be permitted to exceed. The limiter is ‘zero response time’ and controls peaks without any audible distortion. For transparent ‘peak protection’ the output gain control should be set to ensure that the Peak Limiter operates only occasionally. Alternatively, the unit can be driven into heavy limiting for creative effects.
Input/Output Bargraph Meter: An eight segment LED bargraph level meter monitors the output signal level over a range of -20dB to +15dB. When Bypass is selected this meter reads input level. |
Shure DP11EQE Dynamics Processor Specification:
GENERAL:
Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
Sampling Rate: 48 kHz
Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
Voltage Gain:
1 dB +/- 1dB (power off)
12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
0 dB +/- 2 dB (equal input and output sensitivities)
Impedance:
Input: 47 kilohms +/- 20% actual
Output: 120 ohms +/- 20% actual
Input Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Output Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Total Harmonic Distortion
LED Signal Indicators
Signal: 40 dB
Clip: 6 dB down from input clipping
Propagation Delay from Input to Ouput
0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
Polarity
Input to output: inverting optional (default: non-inverting)
XLR: pin 2 positive with respect to pin 3
1/4-inch TRS: tip positive with respect to ring
Operating Voltage
DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
Temperature Range
Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
Fuse
DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
Dimensions
219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
Weight: 930 g (2.05 lbs)
DYNAMICS PROCESSOR
Gate and Expander:
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Gate Hold Time: 0 to 0.5 seconds
AGC Leveler
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0.2 to 3 seconds
Decay: 0.5 to 5 seconds
Hinge: Threshold to 1 dB, 0.5 dB resolution
Compressor and Limiter
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Knee: Hard or Soft selectable
No Overshoot Peak Limiter
Propagation delay: 1 ms
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0 msDecay: 100 ms
PARAMETRIC EQUALIZER
Parametric Filter Frequency Bands
Up to 9 bands, variable frequency, variable Q
Boost/Cut Range
+6 dB to 18 dB per band
Q Range
1/40-octave to 2 octave
High and Low Shelf/Cut Filters
Shelf, +6 to 18 dB per filter
Cut, 12 dB per octave nominal
DELAY
Up to 1.3 seconds, 21 microsecond resolution
| SHARK FBQ100
Automatic Feedback Destroyer with Integrated Microphone Preamp, Delay Line, Noise Gate and Compressor
High performance single channel Feedback Destroyer with integrated microphone preamp, delay line, noise gate and compressor
Automatically and "intelligently" locates and destroys up to 8 feedback frequencies
Narrow FBQ filters for extremely effective feedback suppression, while keeping highest sonic quality
Ultra-low noise Mic/Line input with Gain control and +48 V phantom power
Delay line with up to 2.5 seconds of delay, adjustable in meters, feet and msec
Noise gate with automatic and manual parameter settings
Automatic compressor with variable density
Subsonic filter with adjustable cut-off frequency
Balanced inputs and servo-balanced outputs with ¼'' TRS and gold-plated XLR connectors
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany |
In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.
The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.
All four channels have the following controls:
Threshold - allows you to set the level at which the compressor starts affecting the gain
OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.
Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.
Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.
Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.
Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.
PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.
Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.
All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | Typically >50 dB at 1 kHz | | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 118 dB, unweighted | | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | IMD | | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Compressor Threshold Range | -40 dBu to +20 dBu | | Compressor Ratio | 1:1 to infinity:1 | | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | | Compressor Attack/Release Characteristic | AutoDynamic™ | | Compressor Attack Time | Program-dependent | | Compressor Release Time | Program-dependent | | Compressor Output Gain | -20 to +20 dB | | Limiter Threshold Range | 0 dBu to +24 dBu (off) | | Limiter Ratio | infinity:1 | | Limiter Type | PeakStopPlus® two-stage limiter | | Limiter Stage 1 | PeakStop® brickwall limiter | | Limiter Stage 1 Attack Time | Zero | | Limiter Stage 1 Release Time | Zero | | Limiter Stage 2 | Predictive intelligent program limiter | | Limiter Stage 2 Attack Time | Program-dependent | | Limiter Stage 2 Release Time | Program-dependent | | OverEasy® Switch | Activates the OverEasy compression function | | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | | Bypass Switch | Activates the direct input-to-output hard-wire bypass | | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | | Function Switches | LED indicator for each front-panel switch | | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 20 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | | Unit Weight | 5.2 lbs. (2.4 kg) | | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
The AD2055 combines 100% discrete, pure class A signal amplifiers with state-of-
the-art passive and active filter topologies. The AD2055's unique circuitry delivers
very high resolution transient detail at the operational extremes of real world equalization
demands. The AD2055 auto-bias DC servo loop control eliminates the need for all
interstage capacitor coupling. The AD2055 breathes life into all musical performances!
AD2055 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Minimum audio signal path
Dual mono operation
Transparent active and passive filter design
High headroom +30dB Very low noise -94dB
Fully balanced inputs and outputs
DC coupled, no transformers in audio path
Switched frequencies in high and low bands
Mid bands use X10 frequency for extended range
Wide bandwidth -3dB 1Hz to 450kHz
Low distortion less than 0.5% THD and IMD
All signal routing with sealed silver relays Conductive
plastic potentiometers for low noise
External 150W toroidal power supply 100% discrete
power supplies for audio path
Long lasting, stainless steel hardware
SONIC EXCELLENCE
The Avalon AD2055 Pure Class A music equalizer is the most powerful, low noise
parametric equalizer available today. Designed to optimize absolute signal integrity
and musical performance, the AD2055 combines the best of active and passive filter
topologies with sonic excellence unequaled by lesser designs. The AD2055 is the
perfect solution for two buss music-program equalization, special instrument EQ and
FX applications and ultra high performance mastering studio's.
Features include state-of-the-art, balanced 100% discrete, Pure Class A signal amplifiers,
practical user features and rugged hardware designed to deliver true high performance
audio for many years.
PASSIVE-ACTIVE FILTER DESIGN
Avalon equalizers feature the unique combination of both active and passive filter EQ designs.
This special combination enables the AD2055 to deliver high speed transient detail at the
operational extremes of real-world equalization demands. The passive high and low bands offer
alternate musical tone range to the full function active parametric mid bands. Passive equalizers
have long been a favorite with music lovers around the world. Full bodied, powerful (up to +/-32dB,
64dB range !) and sweet frequency selections are the benefits of the passive high-low EQ bands.
The full bandwidth twin mid bands provide variable frequency selection (X10 frequency multipliers
for very wide range), variable Q (width) and amplitude control.
MINIMUM SIGNAL PATH DESIGN
Avalon's advanced true symmetry design offers high-voltage, large headroom, extended bandwidth
and very low noise. The use of 100% discrete, Pure Class A signal amplifiers give the serious music
professional unlimited sonic character and a natural harmonic detail that enhances the program
material and becomes one with the music itself. The Avalon AD2055 breathes life!
AD2055 SPECIFICATIONS
Circuit Topology High-voltage 100% discrete, balanced and symmetrical
Class A
Output Gain Range Unity Gain
Maximum Input Level +30dB balanced XLR pin 2 hot
Maximum Output Level +32dB balanced 600 ohms, DC coupled, high-current
discrete Class A
Input / Output Type XLR type, pin 2 hot balanced
Noise 20kHz Unweighted -94dB (EQ in)
Distortion THD, IMD 0.5% (typical 0.05% at +6dB 1kHz)
Frequency Response -3dB 1Hz to 450kHz (input band limited)
Equalizer Type Passive high and low bands plus two fully parametric mid
bands
Bypass Hard-wire relay bypass for equalizer in-out
Low Band F1 Passive, amplitude to -32dB to +32dB shelf or peak-dip curve
F1 Frequency Range Switched 10 position 18Hz, 25, 30, 50, 72, 100, 150, 215,
300, 450Hz
Mid Band F2 Active, amplitude to -16dB to +16dB peak-dip curve
F2 Frequency Range Variable 35Hz to 450Hz (x10) 350Hz to 4k5Hz, Q (width)
0.3 to 3.0
Mid Band F3 Active, amplitude to -16dB to +16dB peak-dip curve
F3 Frequency Range Variable 160Hz to 2k0Hz (x10) 1k6Hz to 20kHz, Q (width)
0.3 to 3.0
High Band F4 Passive, amplitude to -26dB to +26dB shelf or peak-dip curve
F4 Frequency Range Switched 10 position 1k5Hz, 2k5, 3k5, 5k, 7k2, 10k, 12k5,
15k, 20k, 25kHz
AC-DC Power External AC supply, 150w toroidal transformer, 4 pin cable 90v
isolated,
(B2T Power Supply Included) 100-240v selectable 50/60Hz, 150w max
Dimensions 19 x 3.5 x 12 in (482 x 88 x 305mm)
Shipping weight 30lbs (13.6 kg)
|
Description
The alphaton Feedback-Controller FC-100 is a revolutionary product for every microphone
application including wireless types. It can provide effective feedback control to any sound
reinforcement situation. It can also eliminated string feedback in guitars and bass instruments
which are equipped with piezo or condenser pickups.
The FC-100 provides 6 to 10 dB of feedback protection by analysing the incoming signal,
detecting the presence of feedback and then notching out the feedback frequency.
The FC-100 relieves the sound engineer automatically. It works dynamically and eliminates a
feedback signal before it can grow into a peak. Internally a discriminator circuit detects the
presence of regenerative feedback and triggers the automatic equaliser to insert a notch where
the feedback peak is coming up. This normally prevents other peaks from developing but if they
do, the process is repeated at high speed, thus keeping feedback under control.
Technical Data
In- and Outputs transformer balanced
max. Inputlevel + 3 dB
Gain (RS=200 Ohm, RL=2kOhm) 0 dB
Frequency Response 20 Hz ... 20 kHz, +/- 1,5 dB
Feeback Cancellation 6 ... 10 dB
Power Requirement 30 ... 48 V Phantom
Current drain ca. 8 mA
External Power Supply 9 ... 20 V DC, 3,5 mm jack, tip +
Housing Aluminium Diecast
Weight 285 grams
Dimensions 112 x 60 x 32 mm |
Reviews
There are no reviews yet.