DBX DRIVE RACK PA2 SIGNAL PROCESSOR 2IN/6OUT

• dbx Compression
• AFSTM (Advanced Feedback Suppression)
• Graphic EQ
• 8-Band Parametric EQ (adjusted when using the AutoEQ)
• Subharmonic Synthesis

• Crossover (supports full range, 2-way, and 3-way systems)
• 8-Band Parametric EQs (used for speaker tunings)
• dbx Limiting
• Driver Alignment Delays

The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers.
It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on
the back panel selecting either mode.

Features
Ultra low noise circuitry
Totally phase aligned at crossover point
Switchable Dual Channel 2 way or Single Channel 3 way
Unique 'semi-fixed' crossover point
24dB per octave (Fourth Order) Linkwitz-Riley filters
Separate Summed Mono Output
Balanced Inputs and Outputs
Built in High Pass filters
Intuitive, 'user friendly' layout
Flawless performance in any audio environment

Tamper-Proof Crossover Points
The crossover points are determined internally by the value of 4 resistors per channel; changing
the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of
externally adjusted crossover points, making the crossover points tamper-proof once they are set.
Idle fingers can't fiddle with the crossover points and create havoc with the system!
As a handy guide, a list of common crossover points and their corresponding resistor values are
printed inside the unit's lid, and also set out in the Owner's Manual.
On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid
and High in single channel 3 way mode, with corresponding Outputs on the rear panel.

Balanced Inputs and Outputs
EC-2 has Balanced Inputs and Outputs, on XLR connectors.
The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low
feed (e.g. Left and Right full-range plus a single Sub Bass speaker).
High Pass Filter
There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers
and waste amplifier power.
In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of
differing sensitivities.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard
IEC connector, with built-in fuse and voltage change switch.
Uncompromising Audio Quality
Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels.
It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth
Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the
crossover region.
From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX
EC-2 is a crossover that is suited to any application that requires flawless, transparent sound.
You'll never compromise on Quality when you choose ARX

T E C H N I C A L S P E C I F I C A T I O N S

Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 21 dB
CMRR >45 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 21dB
Frequency Response 30Hz-20KHz +or- 0.5dB
Note: 30 Hz is a function of the High Pass filter
Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted
Distortion 004% THD,0dB,1KHz
Dynamic Range 111 dB
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm
Input Connector type XLR
Output Connector type XLR
Crossover point frequencies are changed internally by varying the value of 4 resistors
per channel.

Front Panel Controls
Low and High Output controls for 2 way mode
Low, Mid and High Output controls for 3 way mode
Marker panels for labelling crossover assigns
2 way/ 3 way status LEDs
Rear Panel
Balanced XLR Inputs and Outputs
Additional summed mono Low output
2 way / 3 way mode switch

With the DSP 260 digital 2-in-6 sound system manager, DYNACORD is continuing its proud tradition in the fi eld of innovative digital signal processors.
Based on the most modern hardware, this system manager offers tried-and-tested as well as new algorithms for the simple and swift construction of active multi-way systems. As much importance has been attached here by the developers to high user-friendliness as to the realization of an extremely favorable price.
24-bit sigma-delta AD/DA converters and a 32-bit floating-point signal processor make possible a dynamic range of 111 dB. In addition to the two analog inputs, a digital stereo input in AES/EBU format is available. A -6 dB pad switch in front of the AD converters offers additional security against overload when the device is connected to mixing desks with very high output levels. The 6 individually mutable outputs are electronically balanced and available on XLR sockets. For all inputs and outputs, easily read LED level meters are provided on the front panel.
Users can choose whether to configure their own systems at the device itself using the controls and display provided or else by means of the intuitive editing software.
3-way stereo, 2-way stereo + FR, 4-way mono + FR etc. Furthermore, factory presets compatible with those of the tried-and-tested DSP-244 are available for Dynacord loudspeaker systems.
In terms of DSP, the device offers parametric and graphic EQs as well as a delay function in the input and crossover, channel EQ, channel delay and a level control with limiter in each output channel.
An RS-232 interface allows Master/Slave operation of multiple devices as well as GPI switching of settings. A PC (the editing software runs under Windows) can be connected via the USB interface on the front panel.
A variable parameter lockout function allows you to determine which settings and parameters can be accessed directly at the device. This is just one of many features that make the DSP 260 an ideal choice also for the rental business.
The wealth of features combined with its outstanding audio performance and favorable price commend this audio system manager for a multitude of professional applications.
General Mains Voltage 100-240 VAC 50-60 Hz Power Consumption 25W Audio Analog Inputs 2x XLR IN, electronically balanced, 2x XLR THRU OUT, electronically balanced Digital Inputs 1x XLR AES/EBU IN Nominal Input Voltage 1.23 V / +4 dBu Maximum Input Voltage (Without -6dB Analog Pad Engaged) 8.7 V / +21 dBu Input Impedance 10k ohm Common Mode Rejection -80 dB @ 1 kHz (typical) A/D Conversion 24-Bit Sigma-Delta Outputs 6x XLR OUT, electronically balanced Nominal Output Voltage 1.23 V / +4 dBu Maximum Output Voltage 8.7 V / +21 dBu Output Impedance 50 ohm D/A Conversion 24-Bit Sigma-Delta Frequency Response 10 Hz-22 kHz (+/- 0.5 dB) THD+N < 0.01% (band limited 22Hz-22kHz) Dynamic Range 111 dB unweighted, band limited 22 Hz - 22 kHz Interfaces USB USB Type B on front panel (PC Interface) 9-pin DSUB Software Confi gurable for GPI Preset Recall or Master/Slave Connection to second DSP 260 unit Signal Processing Sample Rate 48 kHz Data Format 24-Bit Internal Processing 32-Bit Floating Point Physical Dimensions (WxHx) 19 x 14 x 1.75 inches (482.6 x 355.6 x 44.45 mm) Weight (Net) 10.1 lb (4.6 kg) Weight (Gross) 13.0 lb (5.9 kg)