| Content |
Smooth vinyl precision.
ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.
SPECIFICATIONS
Turntable Section
- Drive System: Belt drive
- Motor: DC motor
- Selectable Speeds: 33⅓ and 45 rpm
- Motor Servo: Speed rotation and servo system
- Rotation Speed Variation: +/-1%
- Wow and Flutter: 1%
- Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
- Platter: Aluminum die-cast
- Platter Diameter: 0 in / 300 mm
Tonearm Section
- Type: Aluminum tube, static-balanced
- Effective Arm Length: 8 in / 223.6 mm
- Stylus Pressure Range: 0 to 0 g
- Cartridge Weight Range: 5 to 6.0 g
- Effective Arm Mass: 4 g
- Overhang: 6 mm
- Offset Angle: 25 degrees
- Anti-Skating: Adjustment Supported
- Main Bearing: Stainless steel
Cartridge Section:
- Type: Audio-Technica AT91 moving magnet
- Stylus Construction: Bonded diamond
- Mount: Half-inch
- Frequency Response: 20 Hz to 20 kHz
- Channel Separation: >18 dB
- Channel Balance: 5 dB
- Vertical Tracking: Angle 20 degrees
- Stylus Pressure: 0 g +/-0.5 g
- Cartridge Weight: 0 g +/-0.5 g
- Headshell Weight: 0 g (including screws, nuts and wires)
Phono Equalizer Amplifier
- Type :Moving magnet (MM)
- Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
- Line Output: 140 mV (-17 dBV)
- Phono/Line: Switchable
- Supported Load Impedance: 47 kΩ
Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb
Smooth vinyl precision.
ELAC celebrates its 90th anniversary by saluting the Golden Age of stereo when turntables reigned supreme. The legend of ELAC’s Miracord turntable lives on today, with dealers and customers constantly asking when the ELAC loudspeaker family will finally include a turntable. The resurgence of vinyl has created a groundswell of enthusiasm among audiophiles and even casual listeners, and for those with roots in hi-fi, the ELAC Miracord remains an iconic name from the era of the long-playing disc.
Inert MDF chassis
The 12 lb (5.5 kg) MDF chassis rests on specially developed silicone feet that decouple the deck completely from the surface on which it is placed. |
A MUSICAL FAMILY
The TD 206 and TD 209 turntables are the younger siblings of the revolutionary, multiple-award-winning TD 309. However, they don’t have to live in the shadow of their older brother. Both models are built using only high-quality materials and parts. And both share a number of technical features with the TD 309, ensuring that their replay quality is up there with the best.
The new TP 90 tonearm is based on the tried-and-tested TP 92 and uses the same ultra-low-friction, high-performance bearing and the innovative zero-stiction anti-bias system. The arm tube is made from rolled aluminium that is damped using RMR technology (reduced-modal-resonance), and the stainless-steel counterweight at the end of the arm tube is double-decoupled. Tonearm height, azimuth and overhang are useradjustable.
SPECIAL FEATURES
- Low Noise, Low Voltage electronically speed controlled DC Motor
- Adjustable belt tension for best performance
- Two-part aluminium/acrylic platter
- New TP 90 tonearm with precision Japanese bearings
- Tonearm adjustable for VTA, azimuth and overhang
- Made in Germany
|
The TD 158 is a complete and comfortable record player. Plug-and-play, so to speak. It goes without saying that it features a fully automatic mode of operation, an electronic speed selector and last but not least, a high-quality acrylic cover to keep dust away.
Tonearm and cartridge have been pre-mounted and painstakingly adjusted in the factory. All necessary leads are supplied with the unit and the record player is ready to play with a flick of the wrist. The entry into the wonderful world of analog music is as simple as this!
Fully automatic, internal flat drive belt,
Speeds 33-1/3, 45 rpm, Tonearm THORENS TP 17, Pick-up Cartridge DN 251 S,
Dimensions 440 x 120 x 360 mm (W x H x D),
Finish black structured enamel ,mains adapter, dust cover (acrylic), RCA interconnects
| Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
- Belt drive system with low vibration DC motor
- Central gravity mass point made from artificial stone
- Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
- Low resonance MDF platter with felt mat
- 8,6” ultra low mass tonearm with straight arm tube
- Pre-adjusted tracking force & antiskating
- Gold-plated RCA contacts & cartridge pins
- Colour options: red-black, white-black, silver-black
Specifications:
- speed : 33, 45 (manual speed change)
- Speed variance: 33: 0,2% 45: 0,18%
- Wow & flutter: 33: 0,14% 45: 0,13%
- platter: 300mm MDF
- tonearm: 8,6” metal tube
- effective arm length: 218,5 mm
- overhang: 22,0 mm
- effective tonearmmass: 8,0gr
- counterweight for cartridge mass: 3 - 5,5g (included)
- tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
- output: RCA to phono input
- included accessory: RCA cable, 15V DC power supply
- power consumption: 4,0 watts
- dimensions: 430 x 90 x 300mm (WxHxD)
- weight: 2,7 kg net
|
High-quality materials, a classic design and love for details are the distinctive characteristics of this fully automatic record player. The massive and stable real wood plinth, which is available also with piano lacquer finish, provides the TD 240-2 with a timeless elegance.
This record player has been equipped with the new TP 19-1 tonearm and an extremely silent running precision belt drive beneath the platter, so that the other technical qualities are also most evident. Set-up and connections are effortlessly carried out so that the TD 240 is ready to play within minutes
Specs:
- Operation fully automatic
- Drive System internal flat drive belt
- Motor electronically controlled DC motor
- Speeds 33-1/3, 45, 78 rpm
- Speed Select electronically
- Platter 12” / 0.7 kg (aluminium, non-magnetic)
- Tonearm THORENS® TP 19-1
- Pick-up Cartridge THORENS® TAS 267
- Anti-skating (Bias) by spring (adjustable)
- Automatic Shut-off mechanically
- Cable Capacitance 160 pF
- Power Supply external mains adaptor (115-230 V / 50-60 Hz depending on type)
- Dimensions 430 x 130 x 365 mm (W x H x D)
- Weight 6.4 kg
- Finish solid wooden plinth with black piano laquer, black structured enamel,
- Scope of Delivery mains adapter, dust cover (acrylic), RCA interconnects, operating instructions
|
Best buy turntable with maximum simplicity, outstanding sound quality & USB recording capability!
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental Phono USB table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it into hifi system and computer.
The only plastic here is the stylus guard!
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards and vinyl recording capability.
• Belt drive system
• Integrated motor control with DC power supply secures silent running
• Central gravity mass point made from artificial stone
• Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
• Low resonance MDF platter with felt mat
• 8,6” ultra low mass tonearm with straight arm tube
• Pre-adjusted tracking force & antiskating
• Gold-plated RCA contacts & cartridge pins
• Integrated phono stage with precise RIAA equalisation
• Line level output
• A/D converter for vinyl recording with USB B output
• Colour options: red-black, white-black, silver-black
|
Reviews
There are no reviews yet.