ELAC Miracord 50 Belt Drive Turntable (Black High Gloss)

590.00 incl. GR VAT

In stock

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Availability: Available in 1-3 d. Available in 1-3 d. SKU: Miracord 50 Category:
Smooth vinyl precision. ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a […]

 

Read more

Smooth vinyl precision.

ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.

SPECIFICATIONS

Turntable Section

  • Drive System: Belt drive
  • Motor: DC motor
  • Selectable Speeds: 33⅓ and 45 rpm
  • Motor Servo: Speed rotation and servo system
  • Rotation Speed Variation: +/-1%
  • Wow and Flutter: 1%
  • Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
  • Platter: Aluminum die-cast
  • Platter Diameter: 0 in / 300 mm

Tonearm Section

  • Type: Aluminum tube, static-balanced
  • Effective Arm Length: 8 in / 223.6 mm
  • Stylus Pressure Range: 0 to 0 g
  • Cartridge Weight Range: 5 to 6.0 g
  • Effective Arm Mass: 4 g
  • Overhang: 6 mm
  • Offset Angle: 25 degrees
  • Anti-Skating: Adjustment Supported
  • Main Bearing: Stainless steel

Cartridge Section:

  • Type: Audio-Technica AT91 moving magnet
  • Stylus Construction: Bonded diamond
  • Mount: Half-inch
  • Frequency Response: 20 Hz to 20 kHz
  • Channel Separation: >18 dB
  • Channel Balance: 5 dB
  • Vertical Tracking: Angle 20 degrees
  • Stylus Pressure: 0 g +/-0.5 g
  • Cartridge Weight: 0 g +/-0.5 g
  • Headshell Weight: 0 g (including screws, nuts and wires)

Phono Equalizer Amplifier

  • Type :Moving magnet (MM)
  • Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
  • Line Output: 140 mV (-17 dBV)
  • Phono/Line: Switchable
  • Supported Load Impedance: 47 kΩ

Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb

Smooth vinyl precision. 

ELAC celebrates its 90th anniversary by saluting the Golden Age of stereo when turntables reigned supreme. The legend of ELAC’s Miracord turntable lives on today, with dealers and customers constantly asking when the ELAC loudspeaker family will finally include a turntable. The resurgence of vinyl has created a groundswell of enthusiasm among audiophiles and even casual listeners, and for those with roots in hi-fi, the ELAC Miracord remains an iconic name from the era of the long-playing disc.

Inert MDF chassis

The 12 lb (5.5 kg) MDF chassis rests on specially developed silicone feet that decouple the deck completely from the surface on which it is placed.

Weight 6.00 kg

Reviews

There are no reviews yet.

Be the first to review “ELAC Miracord 50 Belt Drive Turntable (Black High Gloss)”

Your email address will not be published. Required fields are marked *

Quick Comparison

ELAC Miracord 50 Belt Drive Turntable (Black High Gloss) removeDENON DP-300F Belt-driven automatic turntable with cartridge removePro-Ject Essential II with phono USB Turntable Red removeTHORENS TD 240-2 Belt drive Turntable 78rpm (Walnut) removePro-Ject Elemental Turntable Red-Black with Ortofon OM 5 E removePro-Ject Elemental Turntable Silver-Black with Ortofon OM 5 E remove
NameELAC Miracord 50 Belt Drive Turntable (Black High Gloss) removeDENON DP-300F Belt-driven automatic turntable with cartridge removePro-Ject Essential II with phono USB Turntable Red removeTHORENS TD 240-2 Belt drive Turntable 78rpm (Walnut) removePro-Ject Elemental Turntable Red-Black with Ortofon OM 5 E removePro-Ject Elemental Turntable Silver-Black with Ortofon OM 5 E remove
ImageDENON DP-300F Belt-driven automatic turntable with cartridge
SKUMiracord 50DP-300FESIIUSBREDTD 240-2 WalnutELEMENTALRBELEMENTALSB
Rating
Price590.00 incl. GR VAT 369.00 incl. GR VAT 384.39 incl. GR VAT910.00 incl. GR VAT268.99 incl. GR VAT 289.89 incl. GR VAT
Stock

In stock

Only 1 left in stock (can be backordered)

Only 1 left in stock

Available on backorder

Available on backorder

Available on backorder

AvailabilityIn stockOnly 1 left in stock (can be backordered)Only 1 left in stockAvailable on backorderAvailable on backorderAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

Smooth vinyl precision.

ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.

SPECIFICATIONS

Turntable Section

  • Drive System: Belt drive
  • Motor: DC motor
  • Selectable Speeds: 33⅓ and 45 rpm
  • Motor Servo: Speed rotation and servo system
  • Rotation Speed Variation: +/-1%
  • Wow and Flutter: 1%
  • Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
  • Platter: Aluminum die-cast
  • Platter Diameter: 0 in / 300 mm

Tonearm Section

  • Type: Aluminum tube, static-balanced
  • Effective Arm Length: 8 in / 223.6 mm
  • Stylus Pressure Range: 0 to 0 g
  • Cartridge Weight Range: 5 to 6.0 g
  • Effective Arm Mass: 4 g
  • Overhang: 6 mm
  • Offset Angle: 25 degrees
  • Anti-Skating: Adjustment Supported
  • Main Bearing: Stainless steel

Cartridge Section:

  • Type: Audio-Technica AT91 moving magnet
  • Stylus Construction: Bonded diamond
  • Mount: Half-inch
  • Frequency Response: 20 Hz to 20 kHz
  • Channel Separation: >18 dB
  • Channel Balance: 5 dB
  • Vertical Tracking: Angle 20 degrees
  • Stylus Pressure: 0 g +/-0.5 g
  • Cartridge Weight: 0 g +/-0.5 g
  • Headshell Weight: 0 g (including screws, nuts and wires)

Phono Equalizer Amplifier

  • Type :Moving magnet (MM)
  • Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
  • Line Output: 140 mV (-17 dBV)
  • Phono/Line: Switchable
  • Supported Load Impedance: 47 kΩ

Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb

Smooth vinyl precision. 

ELAC celebrates its 90th anniversary by saluting the Golden Age of stereo when turntables reigned supreme. The legend of ELAC’s Miracord turntable lives on today, with dealers and customers constantly asking when the ELAC loudspeaker family will finally include a turntable. The resurgence of vinyl has created a groundswell of enthusiasm among audiophiles and even casual listeners, and for those with roots in hi-fi, the ELAC Miracord remains an iconic name from the era of the long-playing disc.

Inert MDF chassis

The 12 lb (5.5 kg) MDF chassis rests on specially developed silicone feet that decouple the deck completely from the surface on which it is placed.

DENON DP-300F Belt-driven automatic turntable with cartridge Fully automatic operation makes the DP-300F easy to use. With the touch of a button, the tonearm swings over and begins playing your record, returning to its original position when finished. Details: aluminum platter built-in phono preamp belt-drive system with DC servo motor dynamic balance tonearm with universal mount fully automatic operation manual lifter mechanism replaceable moving magnet cartridge included removable dust cover heavy base construction minor assembly required two speeds: 33-1/3 rpm & 45 rpm wow & flutter 0.10% weight: 6 kgs dimensions:17-1/16“W x 4-13/16“H x 15“D

A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.  

The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.

Specifications:

  • speed : 33, 45 (manual speed change)

  • principle : belt drive

  • Speed variance : 33: 0,14% 45: 0,25%

  • Wow & flutter : 0,12%

  • platter : 300mm MDF with felt mat (0,8kg)

  • main bearing : stainless steel

  • tonearm : 8,6” aluminium

  • effective : arm length 218,5 mm

  • overhang : 22,0mm

  • effective tonearmmass : 8,0gr

  • counterweight for mass : 3 - 5,5g (included)

  • tracking force range : 0 - 25mn (OM5 18mn recommended)

  • included accessory : power supply, dust cover

  • Power consumption : 4,5 watts

  • dimensions : 420 x 112 x 330mm (WxHxD)

  • weight : 4,0 kg net

High-quality materials, a classic design and love for details are the distinctive characteristics of this fully automatic record player. The massive and stable real wood plinth, which is available also with piano lacquer finish, provides the TD 240-2 with a timeless elegance.

This record player has been equipped with the new TP 19-1 tonearm and an extremely silent running precision belt drive beneath the platter, so that the other technical qualities are also most evident. Set-up and connections are effortlessly carried out so that the TD 240 is ready to play within minutes

Specs:

  • Operation fully automatic
  • Drive System internal flat drive belt
  • Motor electronically controlled DC motor
  • Speeds 33-1/3, 45, 78 rpm
  • Speed Select electronically
  • Platter 12” / 0.7 kg (aluminium, non-magnetic)
  • Tonearm THORENS® TP 19-1
  • Pick-up Cartridge THORENS® TAS 267
  • Anti-skating (Bias) by spring (adjustable)
  • Automatic Shut-off mechanically
  • Cable Capacitance 160 pF
  • Power Supply external mains adaptor (115-230 V / 50-60 Hz depending on type)
  • Dimensions 430 x 130 x 365 mm (W x H x D)
  • Weight 6.4 kg
  • Finish solid wooden plinth with black piano laquer, black structured enamel,
  • Scope of Delivery mains adapter, dust cover (acrylic), RCA interconnects, operating instructions
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in. The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
  •  Belt drive system with low vibration DC motor
  •  Central gravity mass point made from artificial stone
  •  Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
  •  Low resonance MDF platter with felt mat
  •  8,6” ultra low mass tonearm with straight arm tube
  •  Pre-adjusted tracking force & antiskating
  •  Gold-plated RCA contacts & cartridge pins
  •  Colour options: red-black, white-black, silver-black
Specifications:
  • speed : 33, 45 (manual speed change)
  • Speed variance: 33: 0,2% 45: 0,18%
  • Wow & flutter: 33: 0,14% 45: 0,13%
  • platter: 300mm MDF
  • tonearm: 8,6” metal tube
  • effective arm length: 218,5 mm
  • overhang: 22,0 mm
  • effective tonearmmass: 8,0gr
  • counterweight for cartridge mass: 3 - 5,5g (included)
  • tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
  • output: RCA to phono input
  • included accessory: RCA cable, 15V DC power supply
  • power consumption: 4,0 watts
  • dimensions: 430 x 90 x 300mm (WxHxD)
  • weight: 2,7 kg net
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in. The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
  •  Belt drive system with low vibration DC motor
  •  Central gravity mass point made from artificial stone
  •  Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
  •  Low resonance MDF platter with felt mat
  •  8,6” ultra low mass tonearm with straight arm tube
  •  Pre-adjusted tracking force & antiskating
  •  Gold-plated RCA contacts & cartridge pins
  •  Colour options: red-black, white-black, silver-black
Specifications:
  • speed : 33, 45 (manual speed change)
  • Speed variance: 33: 0,2% 45: 0,18%
  • Wow & flutter: 33: 0,14% 45: 0,13%
  • platter: 300mm MDF
  • tonearm: 8,6” metal tube
  • effective arm length: 218,5 mm
  • overhang: 22,0 mm
  • effective tonearmmass: 8,0gr
  • counterweight for cartridge mass: 3 - 5,5g (included)
  • tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
  • output: RCA to phono input
  • included accessory: RCA cable, 15V DC power supply
  • power consumption: 4,0 watts
  • dimensions: 430 x 90 x 300mm (WxHxD)
  • weight: 2,7 kg net
Weight6.00 kg6.00 kg5.00 kg8.50 kg3.50 kg3.50 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 6.00 kg
Weight 6.00 kg
Weight 5.00 kg
Weight 8.50 kg
Weight 3.50 kg
Weight 3.50 kg