| Content |
Capsule: Hand-crafted, 1" diaphragm, gold-sputtered
Frequency Response: 20Hz-20kHz
Sensitivity: -32 dBV/Pa (25.1mV/Pa)
Polar Pattern: Cardioid
Impedance: ≤ 200 Ohms
Equivalent Noise Level: 16dB (A-weighted)
Max SPL for 0.5% THD @1kHz: 125dB
Power Requirement: Phantom power 48V±4V
Connector: 3-pin XLR | The C 414 B/XLS has been carefully designed to maintain the legendary sonic character of the C 414 family while integrating new features and performance enhancements made possible by new technology. The C 414B/XLS is designed to deliver accurate pickup of all acoustic instruments and voices.
The microphone's 5 pickup patterns are easily selectable via an electronic switch with LED indication and offer the selection of omnidirectional, cardioid, wide cardioid, hypercardioid and figure-eight patterns.
The pickup pattern selector switch utilizes a dual-color LED indicator that provides visual indication of the pattern selected and also changes from green to red to indicate if the microphone's output electronics are being overloaded. The pattern selector can also be used to "lock" the microphone's switch settings by pressing and holding it for 3 seconds.
On the rear of the microphone, an electronic switch allows the selection of -6 dB, -12 dB and -18 dB pre-attenuation levels which are accomplished by changing the polarization voltage to the capsule. The C 414 B/XLS has switchable bass cut filters of 12 dB-per-octave at 40 Hz and 80 Hz, and a 6-dB-per-octave filter at 160 Hz for control of proximity effect. On-axis sensitivity for all patterns is 23 mV/Pa and its self-noise is an extremely low 6 dB-A.
The C 414 B/XLS has a transformerless output and all-metal chassis, making it immune to electrical interference and RF from digital equipment, video monitors and wireless systems. It comes complete in an all-metal road case with the AKG H-85 shock mount, a PF80 external two-stage pop filter, a W414X external windscreen and an individually-measured chart showing the response curve of the microphone. It is also available in factory-matched stereo pairs packaged with a H50 stereo bar instead of the external pop filter.
The C 414B/XLS is built in Vienna, Austria and comes with a three-year limited parts and labor warranty.
Features
High sensitivity and extremely low self noise
Five switchable polar patterns for placement and application flexibility
Two-color LEDs provide quick visual indication of selected polar pattern and output overload
Elastic capsule suspension greatly minimizes structurally-transmitted noise from chassis vibration
H 85 professional shock mount/stand adapter, PF 80 external pop filter and W 414 X external windscreen
High sound pressure level capability and wide dynamic range
Completely immune to electrostatic and electro-magnetic interference from digital gear, computer monitors, etc. thanks to solid metal housing and transformerless output stage
Three switchable bass cut filters and three pre-attenuation pads with LEDs for quick visual indication
All switchable components operate in low impedance circuits for ultra-high relability even in extremely humid conditions
Optional R 414 remote control unit (available by the end of 2004) offers full control of all switchable parameters via standard microphone cable and 3-pin XLR-type connectors
Specifications
Type: 1" large diaphragm pressure gradient microphone
Polar Patterns: Omnidirectional, wide cardioid, cardioid, hypercardioid, figure eight
Frequency Range: 20 to 20,000 Hz
Sensitivity: 23 mV/Pa (-33 dBV) +/-0.5 dB
Max. SPL: 140/146/152/158 dB SPL (at 0/-6/-12/-18 dB)
Preattenuation Pad: -6, -12,-18 dB, switchable
Bass Cut Filter Scope: 12 dB/octave at 40 Hz and 80 Hz; 6 dB/octave at 160 Hz
Power Requirements: 48 V phantom power to DIN/IEC
Connector: 3-pin XLR
Dimensions: 2" x 1.5" x 6.3“
Net Weight: 10.6 oz
Shipping Weight: 5 lbs (2.27 kg) |
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm | Live sound
| Podcasting
Home recording
Vocals
Musical instruments |
Perception 120 |
|
- General-purpose cardioid recording microphone
- Extended frequency response
- Roadworthy construction
- Switchable 20 dB preattenuation pad
- Switchable bass cut filter
- Designed and engineered by AKG in Vienna, Austria
The Perception 120 is a 2/3-inch diaphragm true condenser microphone that offers solid build quality, outstanding performance, and excellent value. The low-mass diaphragm delivers a clear sound with accurate sonic detail. A switchable 20 dB preattenuation pad and bass cut filter make the Perception 120 an excellent choice for a wide range of recording and live sound applications.
Backed by AKG\'s six decades of experience in making microphones and input from sound engineers around the world, the Perception 120 now brings AKG studio quality to musicians and project studio applications.
| Type |
2/3\" Diaphragm True Condenser |
| Polar pattern |
cardioid |
| Frequency range |
20 to 20,000 Hz |
| Sensitivity |
22 mV/Pa (-33 dBV) |
| Max. SPL |
130/150 dB (0/-20 dB) for 0.5% THD |
| Equivalent noise level |
22 dB-A (IEC 60268-4) |
| Signal/noise ratio (A-weighted) |
72 dB |
| Preattenuation pad |
0 dB, -20 dB |
| Bass filter |
12 dB/octave at 300 Hz |
| Impedance |
|
| Recommended load impedance |
>= 1,000 ohms |
| Powering |
|
| Power requirement |
48 V phantom power to DIN/IEC |
| Connector |
3-pin XLR |
| Finish |
metallic blue |
| Dimensions |
53 dia. x 165 mm (2.1 dia. x 6.5 in.) |
| Net weight |
525 g (18.5 oz.) |
| Shipping weight |
955 g (33.7 oz.) |
|
Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone
The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.
|
|
|
|
|
|
|
Professional true condenser microphone for studio and live applications
|
|
|
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
|
|
|
Low-mass gold sputtered diaphragm for ultimate sound reproduction
|
|
|
Perfect for acoustic instruments, voice and overhead etc.
|
|
|
Ultra low-noise transformerless FET input eliminates low-frequency distortion
|
|
Smooth, super-wide frequency response and incredible musicality
|
|
Switchable low-frequency roll-off and -10 dB input attenuation
|
|
Gold-plated 3-pin XLR output connector
|
|
Rugged construction with satin nickel-plated brass body
|
|
Custom microphone stand adapter, windscreen and transport case included
|
|
Manual Download |
Rode's new NTK has the quality and warmth demanded from a tube mic.
With the large 1 in. capsule gold-plated membrane and twin triode tubes
(hand graded and selected), Rode is again setting the standard for value.
This is a tube mic designed exclusively for recording professionals who
want what only the best can offer.
Features:
Dynamic range of 47dB
Ultra low noise of only 12dB
Internal capsule shock mounting
Cardioid polar pattern
20Hz - 20kHz frequency response
Includes a power supply, 30 ft. cable, and stand adapter
Technical Description:
Capsule: Externally polarised 1 in. pressure-gradient condenser
Active Electronics: Unity-gain closed-loop impedance converter;
vacuum-tube input with bipolar buffering
Pickup Pattern: Cardioid
Frequency Response: 20Hz - 20kHz (+/-6dB)
Output Impedance: 200 ohms (100 ohms per leg)
Sensitivity: -38dB re 1V/Pa (12mV @ 94dB SPL) +/-1dB
Equivalent Noise: 12dB SPL (A-weighted per IEC268-15) +/-2dB
Maximum Output: > +29dBu (@ 1kHz, 5% THD into 1k (load)
Dynamic Range: > 147dB (A-weighted, per IEC268-15)
Maximum SPL: > 158dB SPL (@ 1kHz, 5% THD into 1k (load)
Signal/Noise Ratio: > 82dB (A-weighted, per IEC268-15)
External power supply: 100-120V/200-240V AC (user selectable)
50Hz/60Hz, 25VA maximum
Packed Weight: 4.53 kg (Mic only 760 gm)
Accessories included:
Power Supply
30 ft (10 m) Multicore Cable
M2 Standmount plus 3/8-5/8 in. Thread Adapter
Optional Extras: SM2 Shockmount
|
Reviews
There are no reviews yet.