Content |
Analog Inputs Modular
Analog Outputs Modular
Audio Network CobraNet CM-1 Module (optional)
Cooling Left-to-right, 3-stage fan
Data Format 24 Bit linear A/D and D/A conversion, 48 Bit processing
Digital Inputs Modular
Digital Outputs Modular
FIR-Drive Yes
GPIO Control Port 2 x 6-pole Euro block4 Control Inputs (analog 0 - 10 V / logic control) 3 Control Outputs (Relay contact to ground) 1 Fault Output (NC Relay contact)3 Reference Outputs (+5 V / +10 V/ GND)
Internal Processing 2 DSPs Standard (150 MHz, 300 MIPS), DSP-2 Extension Module (3 dual core processors-1200 MIPS total) , 1 DSP per Audio Module (100 MHz, 100 MIPS) 1500 MIPS total without I/O cards
Network Control (IRIS-Net) Yes
Network Interface Ethernet-10/100 MBit/s, RJ-45
Power Consumption 90 W max. (incl. 2 x AI-1, 2 x AO-1, 1 x CM-1 modules)
Power Supply 100 - 240 VAC, 50/60 Hz
Sample Rate 48 kHz internal
Serial Interface 2 Ports, 9pin D-Sub female (Remote Control)
Signal-to-Noise Ratio (A-weighted) 115 dB
Total Harmonic Distortion 0.01 %
Height 2RU 88.1 mm (3.47“)
Width 483 mm (19.02“)
Depth 381 mm (15“)
Weight Net 7.37 kg (16.25 lbs)
|
CobraNet is a network technology for multichannel transmission of digital audio data. The CM-1 is a compact interface module for NetMax to allow connection to a CobraNet network, which allows the simultaneous transmission of up to 32 digital audio input signals and 32 digital audio output.
* Designed for Cinema, Club Sound, Commercial Sound/Life Safety, Concert Sound, House of Worship, Performance & Sports Venues, Stadium Systems, and other applications.
* 100BASE-TX ethernet interface; 100Mbit/s full-duplex Ethernet interface; IEEE 802.3u compatible.
* Secondary 100BASE-TX Ethernet interface. Second Ethernet interface for the connection of a redundant network to establish fault tolerant systems. Internal audio output interface for the transmission of 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length
* Internal audio input interface for receiving 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length.
* Control, monitoring, configuration, and firmware updates via Ethernet protocol.
* Status LEDs. Link, activity, fault, and CobraNet conductor status indication via Ethernet connectors.
|
- Connect 2 TVs or projectors and switch between 4 connected HDMI devices.
- HDMI matrix switch allows you to watch other HDMI devices on 2 screens independently.
- Use the built-in 1080p downscaler in case 1 or more screens do not support 4K resolution.
- Suitable for the latest Ultra HD 4K60 resolution (3840 x 2160/60 Hz), High Dynamic Range (HDR), Deep Color and 4:4:4 chroma colours.
- Supports Dolby Atmos and DTS:X and all other common audio formats.
- With additional digital audio output to also connect your AV receiver using a single cable.
- Supports Audio Return Channel (ARC) to avoid lip-sync problems.
- Switches automatically and/or with remote control.
Connections
|
|
AV input |
4 x HDMI |
AV output |
2 x HDMI |
Digital audio output |
1x Toslink (optical) |
Video
|
|
Video resolution |
Max. 4K60 (3840 x 2160@60 Hz) |
PC resolution |
Max. 2560 x 2048 Hz |
Video bandwidth |
18 Gbps |
Clock frequency |
Max. 600 MHz |
HDMI standard |
HDMI, EDID, DVI, Deep Color 36 bit, x.v. Colour and 3D formats |
HDCP standard |
HDCP 2.2 |
Colour formats |
RGB and YCbCr 4:4:4, 4:2:0 or 4:2:2 |
Colour depth |
Max. 36 bit |
Audio
|
|
HDMI audio |
DTS-HD Master Audio, Dolby TrueHD, Dolby Atmos, DTS:X, Dolby Digital/AC3, DTS 5.1 and PCM stereo |
Optical Audio |
Dolby Digital/AC3, DTS 5.1 and PCM stereo |
General
|
|
Dimensions (h x w x d) |
18 x 242 x 104 mm |
Weight |
620grams |
Power |
100-240 VAC 50/60 Hz, 12 VDC adapter |
|
Dante is a network technology for multi-channel transmission of digital audio data. The DM-1 compact interface module allows EV's NetMax System Controller to connect to a Dante network, enabling the simultaneous transmission of up to 32 digital audio input signals and 32 digital audio outputs.
* Designed for Club Sound, Commercial Sound/Life Safety, Concert Sound, House of Worship, Performance & Sports Venues, Pro Music, Stadium Systems, and other applications.
* Gigabit primary and secondary Ethernet interfaces Typical latency: 1 mS Dante Zen device discovery Compatible with Dante Virtual Soundcard
|
- 8ch mic/line input and 8ch analog output
- 16ch YDIF digital I/O
- SD Card Slot for playback
|
The ZonePRO 1261m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus. The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlled microphone gain allows adjustment of microphone gain per channel. The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone. A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required. The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port. Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control. All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information). ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 1261m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1261m.
SPECIFICATIONS:
Front Panel LED Indicators
Per Output:6 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters
Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute
Analog Inputs:
12 Total - (6) Balanced Mic/Line Inputs, (4) Unbalanced, Mono-Summed RCA Input Pairs, S/PDIF Input
Type:Euroblock (Mic/Line), RCA (Source)
Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):>25kΩ Unbalanced, RF Filtered
Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA
CMRR:> 40dB, typically >55db @ 1kHz
Mic Pre Gain:30 to 60dB
Mic Input Noise (E.I.N.):< -118dBu, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:+15VDC
ANALOG OUTPUTS
Number of Outputs: 6 Total
Type:Electronically Balanced, RF Filtered Euroblock
Impedance:120Ω Balanced, 60Ω Unbalanced
Max. Output Level:+20dBu
A/D PERFORMANCE
Type: dbx Type IV™ Conversion System
Dynamic Range line: >113dB, A-weighted, >110dB unweighted
Type IV dynamic range: >119dB, A-weighted, 22kHz BW: >117dB, unweighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW
SYSTEM PERFORMANCE
Dynamic Range: >110dB A-weighted, >107dB unweighted, 22kHz BW
THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response: 20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk: >80dB typical
Crosstalk input to output: >80dB
Propagation Delay 0.8 msec
POWER REQUIREMENTS
Operating Voltage: 100-240 VAC, 50/60Hz
Power Consumption: 27 Watts
BTU: |
Reviews
There are no reviews yet.