Content |
Audio Frequency Response 50 Hz - 16,000 Hz
Case Material Die cast zinc
Connector Type 3-pin XLR
Dynamic Range 107 dB
Element Condenser (self-biased)
Finish Textured Satin Black
Impedance, Low-Z balanced 200 Ω
Maximum SPL (1% THD) 132 dB
Mic Type Instrumental
Open Circuit Voltage 6 mV/Pascal
Polar Pattern Cardioid
Power Requirement 11 to 52 VDC, 4 mA
Wired/Wireless Wired
Weight Net 6.21 oz (176 g)
|
The E-602 is a cardioid microphone especially suitable for use with bass drums, bass guitar cabs, tubas and other low frequency instruments.
Frequency Response : 20.....16000 Hz
Sensitivity in free field, no load (1kHz) : 1,0 mV/Pa
Min. terminating impedance : 1000 Ohm
Dimensions : d 60 x 153 mm
Weight : w/o cable 550 g
| Excellent for acoustic and electric instruments as well as for vocals, the extremely versatile Beta 57A dynamic microphone provides optimal warmth and presence.
The Beta 57A maintains a true supercardioid pattern throughout its frequency range. This insures high gain before feedback, maximum isolation from other sound sources, and minimum off-axis tone coloration. A completely new grille design lets you take better advantage of proximity effect. The Beta 57A is an exceptionally versatile microphone. Typical applications include drums, guitar amplifiers, brass, woodwinds and vocals.
- Tailored frequency response provides drums, guitars, vocals, and horns with studio quality sound
- Uniform supercardioid pattern for high gain-before-feedback and superior rejection of off-axis sound
- Hardened steel mesh grille that facilitates use of proximity effect and resists wear and abuse
- Neodymium magnet for high signal-to-noise ratio output
- Advanced pneumatic shock mount system that minimizes transmission of mechanical noise and vibration
- Frequency response: 50 to 16,000 Hz
Suggested Applications
Guitar Amp
Bass Amp
Acoustic Guitar
Brass/Saxophone
Snare Drums
Rack/Floor Toms
Congas
Woodwinds
Lead Vocals | Optimized for low-frequency bass punch/high-power SPL handling. Designed for kick drum.
The Shure BETA®52A is a high output dynamic microphone with a tailored frequency response designed specifically for kick drums and other bass instruments. It provides superb attack and "punch“, and delivers studio quality sound even at extremely high sound pressure levels.
The Beta 52A features a modified supercardioid pattern throughout its frequency range to insure high gain-before-feedback and excellent rejection of unwanted sound. A built in dynamic locking stand adapter with an integral XLR connector simplifies installation, particularly if the microphone is to be placed inside a kick drum. The stand adapter keeps the microphone position fixed and resists slipping, even when subjected to sharp blows and strong vibrations. A hardened steel mesh grille protects the Beta 52A from the abuse and wear associated with touring.
Features
- Frequency response shaped specifically for kick drums and bass instruments
- Built–in dynamic locking stand adapter with integral XLR connector simplifies setup, especially inside a kick drum
- Studio quality performance, even at extremely high sound pressure levels
- Supercardioid pattern for high gain before feedback and superior rejection of unwanted noise
- Hardened steel mesh grille that resists wear and abuse
- Advanced pneumatic shock mount system that minimizes transmission of mechanical noise and vibration
- Neodymium magnet for high signal–to–noise ratio output
- Low sensitivity to varying load impedance
- Legendary Shure quality and reliability
Type |
Dynamic (moving coil) |
Frequency Response |
20 to 10,000 Hz |
Polar Pattern |
Supercardioid, rotationally symmetrical about microphone axis |
Output Level |
Open Circuit Voltage: -64 dBV/Pa* (0.6 mV), *1 Pa = 94 dB SPL |
| The e 604 is a cardioid microphone especially suitable for use with drums and brass instruments.
Features
Rugged reinforced glass-fibre body
Low sensitivity to impact and handling noise
Very high sound pressure handling capability
Low distortion microphone
Hum compensating coil
Easy to position due to compact design
Integral stand mount
Delivery Includes
1 e 604
1 drum clip
1 pouch
Technical Data
Frequency Response 40.....18000 Hz
Sensitivity in free field, no load (1kHz) 1,8 mV/Pa
Min. terminating impedance 1000 Ohm
Dimensions d 33 x 59 mm
Weight w/o cable 60 g |
NEW Wider mounting base capable of accommodating a larger range of microphone stands. Even works with the LP Claw.
Specifically engineered for drum and instrument applications, the Beta 56A's compact, pivoting design makes it the ideal choice for these applications.
Its extremely uniform supercardioid pickup pattern provides high gain before feedback and excellent rejection of unwanted noise. A built-in dynamic locking stand adapter with an integral XLR connector simplifies installation. The stand adapter keeps the microphone securely in place, even if it is struck by a drumstick. Typical Beta 56A applications include close miking of tom-toms and other percussion instruments, as well as guitar amplifiers, brass instruments, and woodwinds.
- Built-in stand adapter with dynamic locking system and XLR connector simplifies setup and provides greater flexibility
- Uniform supercardioid pattern for high gain-before-feedback and superior rejection of off-axis sound
- Compact design reduces stage clutters
- Hardened steel mesh grille resists wear and abuse
- Neodymium magnet for high signal-to-noise ratio output
- Advanced pneumatic shock mount system that minimizes transmission of mechanical noise and vibration
- Frequency response: 50 to 16,000 Hz
|
Reviews
There are no reviews yet.