Content |
15" Speaker 300 W 8 Ohms
Recommended for professional audio as a woofer in sealed and vented enclosures.
Product type
Loudspeaker Chassis
Type
PA
Nominal Diameter
15 "
Nominal Diameter
381 mm
Voice Coil
1.5 "
Voice Coil
38.1 mm
Overall diameter
384.8 mm
Pitch Circle Diameter
369.9 mm
Section Diameter
352.3 mm
Diameter of fixing holes
6.4 mm
Depth
148 mm
Nominal Impedance
8 Ohm(s)
Nominal Load Capacity
200 W
maximum rated load
400 W
Sensitivity (1 W / 1 m)
97 dB
Frequency response
46 - 3500 Hz
Voice Coil Material
copper
Magnet
Ferrite
Depth of the magnetic gap
6.35 mm
Thiele & Small Parameter
Fs (Resonance Frequency)
35 Hz
Re (DC resistance)
6.32 Ohm(s)
Qms (mechanical quality)
8.1
Le (inductance of the voice coil)
1.1 mH
Qes (electrical quality)
0.63
Qts (overall quality)
0.58
Vas (equivalent volume)
334.6
Mms (moving mass)
60 g
BL (power factor)
11.5 T/m
Xmax (maximum displacement)
4 mm
Cms (elasticity of the suspension)
0.35 mm/N
Sd (membrane area)
823.7 cm²
Weight
4,9 kg
| High efficiency 15" woofer with a very flat frequency
response up to 2 kHz and high power handling (800W). Good
LF performance, smooth voice response, and compatibility
with compact bass-reflex enclosures, the 15 PK 40 achieves
perfect balance in two-way systems.
Specifications
Nominal Diameter 380 mm (15 in)
Nominal Impedance 8 Ω
Minumum Impedance 6.2 Ω
Power Handling
(50 –500 Hz)
Nominall 400 W
Continuous Program2 800 W
Sensitivity (1W/1m)3 99 dB
Frequency Range 50-2000 Hz
Voice Coil Diameter 76 mm (3 in)
Winding Material Copper
Former Material Glass Fibre
Winding Depth 16 mm (5/8 in)
Magnetic Gap Depth 9 mm (11/32 in)
Flux Density 1.1 T
Thiele & Small Parameters4
Fs 47 Hz
Re 5.1 Ω
Qes 0.33
Qms 5.1
Qts 0.31
Vas 140 dm3 (4.9 ft3)
Sd 855 cm2 (132.5 in2)
η0 4.2%
X max ± 4 mm
X var ± 6 mm
Mms 84 g
Bl 19.7 T·m
Le 2.3 mH
Mounting and Shipping Information
Overall Diameter 394 mm (15.5 in)
Bolt Circle Diameter 374 mm (14.6 in)
Baffle Cutout Diameter 355 mm (13.9 in)
Depth 162 mm (6.4 in)
Flange and Gasket Thickness 16 mm (5/8 in)
Net Weight 8.3 kg (18.3 lb)
Shipping Weight 9.6 kg (21.1 lb)
Shipping Box 450x450x200 mm
(17.7x17.7x8 in)
1 2 hours test made with continuous pink noise signal (6 dB crest factor) within the
specified range. Power calculated on rated minimum impedance. Loudspeaker in
free air.
2 Power on Continuous Program is defined as 3 dB greater than the Nominal rating.
3 Applied RMS Voltage is set to 2.83V for 8 ohms Nominal Impedance. Average
SPL from 200 to 2000Hz.
4 Thiele-Small parameters are measured after a high level 20 Hz sine wave preconditioning
test. | Recommended for professional audio as a mid-bass or floor monitor in a sealed enclosure. Also suitable as a woofer in vented, bass guitar or PA enclosures.
Product type
Loudspeaker Chassis
Type
PA
Nominal Diameter
15 "
Nominal Diameter
381 mm
Voice Coil
2.5 "
Voice Coil
63.5 mm
Overall diameter
384.8 mm
Pitch Circle Diameter
369.9 mm
Cut- out Measurement
352.3 mm
Diameter of fixing holes
6.4 mm
Depth
160 mm
Nominal Impedance
8 Ohm(s)
Nominal Load Capacity
500 W
maximum rated load
1000 W
Sensitivity (1 W / 1 m)
96 dB
Frequency response
42 - 3200 Hz
Voice Coil Material
copper
Magnet
Ferrite
Depth of the magnetic gap
9.53 mm
Thiele & Small Parameter
Fs (Resonance Frequency)
39 Hz
Re (DC resistance)
6.11 Ohm(s)
Qms (mechanical quality)
6.3
Le (inductance of the voice coil)
1.37 mH
Qes (electrical quality)
0.52
Qts (overall quality)
0.48
Vas (equivalent volume)
241
Mms (moving mass)
75 g
BL (power factor)
14.6 T/m
Xmax (maximum displacement)
4.8 mm
Cms (elasticity of the suspension)
0.23 mm/N
Sd (membrane area)
873 cm²
Weight
6,449 kg | |
The 2226J 15" low frequency transducer represents the results of JBL's latest engineering research in high power transducer design. For increased power handling while reducing power compression, a unique direct voice coil-to-air heat dissipation method called Vented Gap Cooling has been used. This process pumps air through the magnetic gap and directly over and around the voice coil to provide immediate heat transfer and reduction in operating temperature. Through the use of new computer-aided magnet optimization and analysis techniques comes a new weight-optimized Symmetrical Field Geometry (SFG) magnet structure, resulting in a reduction of overall driver weight and a significant reduction in harmonic distortion. This new magnet structure offers much of the weight advantage of rare earth magnet structures without their prohibitive cost. Specifications: *Power handling: 600 watts RMS *Voice coil diameter: 4" *Nominal impedance: 16 ohms *Frequency Range: 30-2,500 Hz *Magnet assembly weight: 15 lbs. *Fs: 40 Hz *SPL: 97 dB 1W/1m *Vas: 6.2 cu. ft. *Qms: 5.0 *Qes: 0.33 *Qts: 0.31 *Xmax: 7.6 mm *Dimensions: Overall Diameter: 15-1/4“, Cutout Diameter: 14“, Mounting Depth: 5-1/2“. | LF B&C Speakers 15-PS76 Subwoofer Speaker 15 inch 1100W, 99dB
Product type |
Cone driver |
Brand |
B&C Speakers |
Reference |
15PS76 |
Product code |
ALT15PS768 |
Informations
|
Nominal impedance |
8 ohm |
Dimensional category |
15.5 inch |
Frequency coverage type |
Sub, Low, Midbass |
Manufacturer sensitivity |
99 dB |
Calculated sensitivity |
96.92 dB |
Nominal power handling |
550 W |
Bandwidth |
40÷2000 Hz |
Fundamental parameters
|
Sd |
855 cm² |
Mms |
106 gr |
Le |
1.3 mH |
Re |
5 ohm |
BL |
22.1 T.m |
Small signal parameters
|
Fs |
38 Hz |
Qes |
0.28 |
Qms |
5.2 |
Qts |
0.26 |
Vas |
164 L |
Datas
|
Xmax |
±7.5 mm |
Calculated Xmax |
±7.6667 mm |
EBP |
136 Hz |
Zmin |
6.3 ohm |
Fs / Qts |
146 Hz |
Vas * Qts² |
11.09 L |
Efficiency |
3.3 % |
Calculated efficiency |
3.09 % |
Weight |
~8.7 kg |
Dimensions
|
Voice coil diameter |
3 inch |
Winding depth |
19 mm |
Gap height |
11 mm |
Outside diameter |
393 mm |
Baffle cutout diameter |
354 mm |
Front thickness |
16 mm |
Depth after front |
155 mm |
Shape & Materials
|
Front chape |
Cylindrical |
Magnet type |
Ferrite |
Basket masterial |
Aluminium |
Winding material |
Copper |
Voice coil former |
Glass fiber |
Surround material |
Cloth |
EAN 8059300642818 |
Reviews
There are no reviews yet.