| Content |
The Soundweb London BLU-320 offers configurable I/O, CobraNet audio, and a high bandwidth, fault tolerant digital audio bus.
The BLU-320 is configurable through HiQnet™ London Architect. A rich palette of logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.
This processor features CobraNet audio with primary and secondary ports for fault tolerance. Control is through a separate Ethernet port which allows CobraNet and control networks to be easily separated or mixed depending upon requirements.
The BLU-320 also features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber optic media converters can be used to increase the distance between devices to over 40km.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-320 to be integrated with GPIO compatible devices. The
Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-320 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.
KEY FEATURES:
- Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Rich Palette of Logic Objects
- CobraNet Audio
- 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from HiQnet London Architect
| More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 234xs Crossover you'll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world's finest processors. The 234xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 234xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 234xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs.
XLR balanced ins and outs
Mode switches for mono 4-way or stereo 2-way/3-way operation
Low frequency summed (subwoofer) output
x10 range switch on both channels
40Hz high pass (low cut) filter both channels
Phase reverse switch on all outputs
Individual level controls on all outputs
24dB per octave Linkwitz-Riley filters (the professional standard)
Stereo/Mono status LEDs indicate the selected mode
dbx® 2 year parts and labor as standard
CSA NRTL/C approved
CE compliant
| Input Connectors |
XLR |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
| Max Input |
>+22dBu balanced or unbalanced |
| CMRR |
>40dB, typically >55dB at 1kHz |
| Output Connectors |
XLR |
| Output Type |
Impedance-balanaced/unbalanced, RF filtered |
| Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
| Bandwidth |
20Hz to 20kHz, +/-0.5dB |
| Frequency Response |
90 kHz, +0/-3 dB |
| Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
| Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >93dB (Mid Output), >90dB (High Output) |
| Signal-to-Noise (Mono Mode) |
>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output) |
| Dynamic Range |
> 106 dB, unweighted, any output |
| THD+Noise |
| Interchannel Crosstalk |
| Crossover Frequencies (Stereo Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting) |
| Crossover Frequencies (Mono Mode) |
Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz |
| Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
| Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
| Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
| x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
| Mode Switch |
Selects stereo/mono and 2/3/4-way operation |
| LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
| Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
| Operating Voltage |
100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz |
| Operating Temperature |
32°F to 113°F (0°C to 45°C) |
| Power Consumption |
15W |
| Power Connector |
IEC receptacle |
| Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
| Unit Weight |
4.0 lbs. (1.8 kg) |
| Shipping Weight |
5.8 lbs. (2.6 kg) |
|
Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.
A/D Conversion 24-Bit Delta-Sigma
A/D Conversion 24-bit/sigma-delta (linear phase) 128 times oversampling
Analog Inputs 2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced)
Analog Outputs 6 XLR (Electronically Balanced)
Control Protocol Front Panel USB Connector
D/A Conversion 24-bit/sigma-delta 128 times oversampling
D/A Conversion 24-Bit Delta-Sigma
Data Format 24-Bit
Digital Inputs 1 XLR AES/EBU (2 Ch)
Dynamic Range 111 dB (unweighted, band limited 22 Hz - 22 kHz)
Electronics Type Processor
FIR-Drive No
Frequency Response 10 Hz - 22 kHz (±0.5 dB)
Input Impedance (Balanced) 10 kΩ
Internal Processing 32-Bit Floating Point
Mains Voltage 100-240 VAC
Maximum Input Voltage 8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged)
Maximum Output Voltage 8.7 V / +21 dBu
Nominal Input Voltage 1.23 V / +4 dBu
Nominal Output Voltage 1.23 V / +4 dBu
Output Impedance (Balanced) 50 Ω
Power Consumption 25 W
Sample Rate 48 kHz
THD+N < 0.01% (band limited 22 Hz - 22 kHz)
Height 1RU 44.45 mm (1.75“)
Width 482.6 mm (19“)
Depth 355.6 mm (14“)
Weight Net 4.6 kg (10.14 lbs) |
- 2 analog inputs and 6 analog outputs for maximum flexibility
- High-end 96 kHz converters for ultimate signal integrity and wide dynamic range (120 dB)
- Precise Dynamic EQs for level-dependent equalization and extremely musical Parametric EQs, selectable for all inputs and outputs
- Several types of EQs (LP/BP/HP) for each input and output
- “Zero“-attack Limiters on all output channels for optimal speaker protection
- Four different mono and stereo output operating modes
- Individual crossover filter types (Butterworth, Bessel and Linkwitz-Riley) with selectable roll-off characteristics from 6 to 48 dB/octave
- Adjustable Delays for all inputs and outputs—allow manual or automatic correction for room temperature, phase and arrival time differences
- 60 user-defined internal presets storable
- Servo-balanced, gold-plated XLR connectors for all inputs and outputs
- Internal switch-mode power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
| Crossover 2-Way stereo or 3-way mono mode Additional subwoofer output Linkwitz-Riley filter with 24 dB / octave Sub-woofer frequency range separately adjustable Individual output gain controls and output mute switch for all bands 2 Balanced XLR inputs with gold-plated contacts 5 Balanced XLR outputs with gold-plated contacts Switchable 25 Hz low-cut filter to protect loudspeakers from infrasound Easy-to-read status LEDs Built-in power supply 100-240V, 50-60 Hz Dimensions (H x W x D): 44 x 483 x 147 mm Weight: 1.6 kg |
With 6 inputs and 4 outputs the dbx ZonePro? 640 and 641 provide flexible signal routing,
powerful DSP processing and multiple control interfaces for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 640/641 deliver the
highest quality tools available. Even the input and outputs connectors were chosen for their
standard usage and reliability. The ZonePro products offer Euroblock connectors for balanced
signals and RCA connectors for interfacing with consumer equipment often used in commercial
applications; there is also a simple analog input buss that allows inputs to be sent from one
unit to the next for unit and job scalability. The 640 and 641 provide every necessary processing
tool, from the input processing like gain control and EQ available on all inputs to highly sophisticated
and specific functions such as selectable paging microphone processing including Gating,
De-Essing, Auto Gain Control, Compression and Feedback Suppression. The heart of the
ZonePro products is the Routing module that provides of course Primary Source Selection
but also Source Ducking for Paging and Priority Override. The outputs also offer a wealth of
processing designed for commercial applications like our patent-pending AutoWarmth? function
that was co-developed with JBL to provide natural low frequency extension at any signal level.
Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay for system
optimization. With the ZonePro? every tool is at your disposal to maximize the response of
your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters.
The ZonePro? 640 and 641 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? Windows? 2000 and XP GUI
? IEC, UL and CSA Approvals
|
Reviews
There are no reviews yet.