Content |
- Frequency range (-3 dB): 40 Hz to 35 kHz
- Maximum sound pressure level (music): 110.5 dB SPL (Peak @ 1 m)
- Electronics inputs/impedance type: XLR: Balanced, 10 kΩ
- RCA connectors: Unbalanced, 10 kΩ with input sensitivity compensation
- Amplifier for middle and bass range: 80 W, class AB
- Power amplifier for the height range: 50 W, class AB
- Automatic Standby mode
- Shutdown: After approx. 30 minutes without input signal
- End standby mode: By applied signal > 3 mV
- Power supply voltage: 220 to 240 V (fuse: T2AL/250 V) or 100 to 120 V (fuse T3.15AL/250 V)
- Connections: IEC socket and separate power cable
- High-pass filter: Variable, range 45/60/90 Hz
- Level Bass (0 - 250 Hz): Variable, +/- 6 dB
- Middle/Bass (160 Hz, Q = 1): Variable, +/- 3 dB
- Level Heights (4.5 - 35 kHz): Variable, +/- 3 dB
- Power on/off: Switch On/Off on the rear
- Power consumption in standby mode: 0.5 W
- LED for power On/Off and standby
- Woofer: 2 x 5“(13 cm) Flax Cone woofer
- Tweeter: 1“(25 mm) aluminium/magnesium with M-profile
- Cabinet construction: 15 mm MDF
- Finish: Vinyl, walnut veneer, black lacquer
- Dimensions with four rubber feet (H x W x D): 478 x 211 x 279 mm
- Weight: 11 kg
|
PRICE PER UNIT The most powerful AX monitor With its power and radiation characteristics, the brand new A8X is suitable for both nearfield and midfield monitoring. With a price/performance ratio that could hardly be better, this monitor is a perfect entry into these monitoring fields. The A8X is equipped with the X-ART tweeter and a large (8.5”) midwoofer, a combination that adds both a very deep and yet very tight bass response to the unsurpassed reproduction qualities of the ADAM proprietary tweeter: a licence to thrill. Cabinet- and bass reflex-construction Like the other AX-Series models, the upper corners of the A8X are slanted to minimize reflections. The very large, double bass reflex tubes on the front have been specifically designed to perfectly match the midwoofer with its large voice coil. Amplification and controls With a 50W A/B amplifier for the tweeter and a 150W PWM amplifier for the midwoofer, the A8X has power in abundance and is the brawny monitor of the AX-Series. On the rear panel are several controls: a gain for the high frequencies (± 4dB) and two shelf filters for the high and low frequencies. There are both XLR (balanced) and RCA (unbalanced) connectors on the rear panel of the speaker, which allow the A8X to be used in almost any application. Review: A8X: a "powerful link" between near- and midfield monitors! "The A8X is a powerful link between ADAM´s AX Series and the formidable and more expensive SX Series. Its all-in-all homogenous tuning, the deep and precise bass as well as the brilliant mid- and high-frequency reproduction make this speaker a huge recommendation for ambitious people without deep pockets." (Professional Audio 10/2010) Mid-Woofer | | Number | 1 | Basket Ø | 8.5" (220 mm) | Voice coil Ø | 1.5" (38 mm) | Cone material | Carbon/Rohacell/Glass Fiber | Tweeter | | Number | 1 | Type | X-ART | Diaphragm area | 4 inch² (2420 mm²) | Equiv. Diaphragm Ø | 2" (56 mm) | Velocity transform ratio | 4:1 | Diaphragm weight | 0.17 g | Built-in Amplifiers | | Mid-Woofer | 1 | Type | PWM | Amp. power RMS / music | 150 W / 225 W | Tweeter | 1 | Type | A/B | Amp. power RMS / music | 50 W / 75 W | Control panel | | Input Sensitivity | -∞ to +14 dB | High Shelf EQ > 5 kHz | ±6 dB | Low Shelf EQ | ±6 dB | Tweeter gain | ±4 dB | Input connectors | | Analog | XLR / RCA | General data | | Frequency response | 38 Hz - 50 kHz | THD 90dB/1m > 100 Hz | ≤0.5 % | Long term output | ≥112 dB | Max. peak | ≥120 dB | Crossover frequencies | 2300 Hz | Input impedance | 30 KOhm | Weight | 28.7 lb (13 kg) | Magnetically shielded | No | Height x Width x Depth | 15.5" (400 mm) x 10" (255 mm) x 12.5" (320 mm) | Warranty | 5 Years | Delivery contents | Power cord, Manual |
|
PRICE PER UNIT ADAMs A7 & A7X: the evolution of a legend The predecessor to the A7X, the A7, became the most famous of all ADAM monitors in a very short time. Not only has it been reviewed over three dozen times with outstanding results, it has also received numerous awards. The A7 quickly gained mass appeal, praised in many of the worldʼs largest internet forums. Still today, the A7 are the reference monitors in many smaller studios. With the A7X, ADAM Audio proudly presents the evolution of a legend. It takes everything that made the A7 such an outstanding speaker to a new level. Driver technology The first aspect that distinguishes the old from the new model is the X-ART tweeter. The ʽXʼ stands for ʽeXtended frequency responseʼ and thus for one of the features of the Accelerating Ribbon Technology that has been drastically improved: the frequency response. It now extends all the way up to 50kHz. In addition, the X-ART tweeter has a higher efficiency and higher maximum sound pressure levels. The perfect integration with the lower frequencies has been achieved with a newly designed 7” midwoofer. It has been redesigned with a much bigger voice coil (1.5”) and is driven by an amplifier with twice the power compared to its predecessor. This combination produces an amazing sound and pressure levels with an almost distortion-free musical reproduction. Amplifiers / controls Each driver has its own dedicated amplifier. A 50W A/B amp is responsible for the X-ART tweeter, while the midwoofer is being driven by a 100W PWM amp. The front panel includes a power switch and a control for the volume that retains the volume setting independently from the on/off switch. On the rear panel are several additional controls: a gain for the high frequencies (± 4dB) and two shelf filters for high and low frequencies. To ensure greater compatibility, there are both XLR (balanced) and RCA (unbalanced) connectors. Mid-Woofer | | Number | 1 | Basket Ø | 7" (175 mm) | Voice coil Ø | 1.5" (38 mm) | Cone material | Carbon/Rohacell/Glass Fiber | Tweeter | | Number | 1 | Type | X-ART | Diaphragm area | 4 inch² (2420 mm²) | Equiv. Diaphragm Ø | 2" (56 mm) | Velocity transform ratio | 4:1 | Diaphragm weight | 0.17 g | Built-in Amplifiers | | Mid-Woofer | 1 | Type | PWM | Amp. power RMS / music | 100 W / 150 W | Tweeter | 1 | Type | A/B | Amp. power RMS / music | 50 W / 75 W | Control panel | | Input Sensitivity | -∞ to +14 dB | High Shelf EQ > 5 kHz | ±6 dB | Low Shelf EQ | ±6 dB | Tweeter gain | ±4 dB | Input connectors | | Analog | XLR / RCA | General data | | Frequency response | 42 Hz - 50 kHz | THD 90dB/1m > 100 Hz | ≤0.5 % | Long term output | ≥106 dB | Max. peak | ≥114 dB | Crossover frequencies | 2500 Hz | Input impedance | 30 KOhm | Weight | 20.3 lb (9,2 kg) | Magnetically shielded | No | Height x Width x Depth | 13.5" (337 mm) x 8" (201 mm) x 11" (280 mm) | Warranty | 5 Years | Delivery contents | Power cord, Manual |
|
MYTHO 6 is a two-way reference studio monitor that features a high quality large metal dome tweeter for the best vocal reproduction and a 6” neodymium vented woofer with a large sized 51 mm voice coil that guarantees very high energy for tight and controlled bass reproduction and perfect thermal stability with minimum power compression.
The magnetic circuit features a special air ventilation to reduce air compression, air noises and minimize distortion in large excursion situations. The MYTHO 6 is equipped with two separate amplifiers: 200 W for the low frequencies and 100 W for the high. The design is a classic AB circuit, unparalleled for low distortion and natural sound. The signal processing is executed from a dedicated high quality DSP processing. It features a solid aluminium cabinet internally braced and reinforced to improve low frequencies behaviour and reduce resonances.
Acoustical Specifications |
---|
Frequency Response -3 dB: | 40 Hz | ÷ 20 kHz | Max SPL: | 114 dB | | Horizontal coverage angle: | 110° | | Vertical coverage angle: | 70° | | Compression Driver: | 1" neo, metal dome | | Woofer: | 6.5" neo, ICC technology | |
INPUT/OUTPUT SECTION |
---|
Input connectors: | combo XLR/Jack | | Input sensitivity: | -6/+6 dBu | |
PROCESSOR SECTION |
---|
Crossover frequencies: | 1900 Hz | | Protections: | thermal, excurs., rms | | Limiter: | soft limiter | | Controls: | bass tilt, roll-off, treeble tilt, desktop, DSP controlled | |
AMPLIFIER SPECIFICATIONS |
---|
High frequencies: | 100 Watts | | Low frequencies: | 200 Watts | | Cooling: | convection | | Connections: | vde | |
CABINET |
---|
Cabinet Material: | die cast aluminum | | Hardware: | orientation adjustable stand | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 370/14.5 mm/inch | | Width: | 265/10.4 mm/inch | | Depth: | 250/9.8 mm/inch | | Net Weight: | 10.5/23 Kg/Lbs |
|
The Solo6 Be monitor will surprise you in the very first minutes you spend with it, partly due to its size/extended bass response (40Hz at -3dB). The 6.5" "W” composite sandwich mid-woofer combines neutrality in the midrange, fullness in the midbass register and bass control. Its compactness and the choice of a large front laminar port guarantee easy integration in studios that need a near field monitor without any acoustic compromise. The user settings on the back of the Solo6 Be, combined with its compactness, make it easy to carry and to adjust according to the acoustics of each studio.
Specifications Frequency response : | 40Hz - 40kHz | Maximum SPL : | 113dB SPL (peak @ 1m) |
Input :
|
Type/Impedance: symmetrical/10 kOhms
Connector: XLR
Sensitivity: Adjustable, +4dBu or -10dBV
| Bass/mid-range : | 150W rms, BASH® technology | Treble : | 100W rms, AB class |
Electric supply :
|
Local supply power: 230V (1.6A fuse)
115V (3.5A fuse)
Connection: removable IEC supply wire
|
Visualization and control :
|
Input sensitivity selector
Adjustable tweeter and woofer levels with potentiometers
Power On/off switch
Voltage selector
| warning light : | Power on LED |
Electric supply :
|
Local supply power: 230V (1.6A fuse)
115V (3.5A fuse)
Connection: removable IEC supply wire
| Woofer : | 6W4370B, 6-1/2" (16.5cm) Focal "W" composite sandwich cone speaker | Tweeter : | Focal TB871 Beryllium inverted dome tweeter | transducer shielding : | Integral through cancellation magnets or by magnet design | Box : | 7-1/2" (19mm) MDF panels |
Finish :
|
Dark red natural veneering side panels, black body
| Dimensions (HxWxD) : | 13 x 9-7/16 x 11-7/16 " (330x240x290mm) | Weight : | 24.2lb (11kg) |
|
PRICE PER UNIT S1X The S1X nearfield monitor delivers high quality sound in a very small cabinet. The S1X has all the critical features of the new SX-Series: the X-ART tweeter in combination with the ADAM designed class A/B amplifier and the HexaCone woofer with optimized magnet/voice-coil systems, driven by premium PWM amplifiers. The smallest reference speaker The combined features of crystal clear resolution, tight and precise low-frequency reproduction and the effortless musical reproduction sets this speaker apart from all conventional designs. The S1X is the first choice in all environments that require high quality within a small space, whether it is a smaller studio, an OB vehicle, or a 5.1 installation. Woofer | | Number | 1 | Basket Ø | 6" (156 mm) | Voice coil Ø | 1.5" (37 mm) | Cone material | HexaCone | Tweeter | | Number | 1 | Type | X-ART | Diaphragm area | 4 inch² (2420 mm²) | Equiv. Diaphragm Ø | 2" (56 mm) | Velocity transform ratio | 4:1 | Diaphragm weight | 0.17 g | Built-in Amplifiers | | Woofer | 1 | Type | PWM | Amp. power RMS / music | 200 W / 280 W | Tweeter | 1 | Type | A/B | Amp. power RMS / music | 50 W / 100 W | Control panel | | Input Sensitivity (coarse) | ±10 dB | High Shelf EQ > 6 kHz | ±6 dB | Low Shelf EQ | ±6 dB | Tweeter gain | ±4 dB | Input connectors | | Analog | XLR | General data | | Panel | Rear | Frequency response | 40 Hz - 50 kHz | THD > 80 Hz | ≤1.5 % | Long term output | ≥103 dB | Max. peak | ≥113 dB | Crossover frequencies | 2200 Hz | Input impedance | 10 KOhm | Weight | 13.2 lb (6 kg) | Magnetically shielded | Optional | Height x Width x Depth | 11.5" (295 mm) x 7" (175 mm) x 10" (260 mm) | Warranty | 5 Years | Delivery contents | Power cord, Manual |
|
Reviews
There are no reviews yet.