Content |
- Rack mount stereo powered monitor speaker system
- New AES/EBU digital input
- lndependent MUTE function
- Sophisticated control panel section
- Ideal where space is at a premium
RM-2 is the ideal solution for monitoring needs in various space-challenged environments such as machine rooms, VTR monitoring, surveillance, mobile and stationary control rooms, theme park applications where audio monitoring is needed and the room for installation is not enough. Adding these new feature sets, RM-2 is now more versatile to various applications. - Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
- AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
- Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
- Independent MUTE function by holding down CH SEL key for a while.
- Auto Mute when powering on*.
- D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
- Multi-voltage power supply.
Speaker Section
- Unit: 110 x 40mm cone type, magnetically shielded, x 2
- Impedance: 8 ohms
- Output SPL: 84 dB/W (1m)
- Frequency response: 200Hz to 20kHz
Amplifier Section
- Rated output power: 10W or more (8 ohms, 1kHz)
- Residual noise: -60 dBV or less (DIN AUDIO)
- Distortion: 0.5% or less (10W / 4 ohms, 1kHz)
Digital input
- Connector: XLR-3-31 type
- Digital input Format: IEC60958 (AES/EBU)
- Digital inputSampling frequency: 44.1kHz to 96 kHz
Analog input
- Connector: XLR / 1/4" combi-jack
- Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
- Analog input Input impedance 10k ohms or more
Phones
- Connector: 1/4" stereo jack
- Applicable load imp. 8 ohms or more
- Rated output power 20mW + 20mW (32 ohms, 1kHz)
General
- External dimensions: 430(W) x 44(H) x 282(D) mm
- Weight: Approx. 3.5kg
- Power requirement: 100 - 240V~, 50/60Hz
- Power consumption: 10W
|
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)
|
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
|
InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz
high pass filter 30Ηz & 50Ηz
|
Reviews
There are no reviews yet.