Content |
Furman M10Lx E Power Conditioner form the Merit Series Power Conditioners is the perfect low cost AC power solution for any rack mount system. Install an Furman M10LxE in to the top slot of your rack, and the 10 switched outlets in the rear panel will power up and protect all your equipment up to a 10 amp load. It not only protects anything plugged into it from spikes and surges, but also has a built in AC noise filter to rid the system of RFI / EMI interference.
TheFurman M-10Lx E also features two slide out, swivelling light fixtures to provide discreet illumination of your equipment. A dimmer knob allows the user to adjust the level of illumination. Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.
Features
- AC Noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI)
- Spike & surge protection ensures equipment stays safe and your power stays clean
- 10 rear panel outlets, with front panel convenience outlet
- 10 amp rating, with circuit breaker
- Two retractable LED light fixtures with dimmer control for convenient rack illumination
- Three year warranty
Specification
- Maximum Output Current: 10 amps
- Lamps: LED
- Operating Voltage: 230VAC 50Hz
- Spike Protection Mode: Line to neutral
- Peak Impulse Current: 12,000 amps
- Maximum Continuous Operating Voltage: 650 Volts
- Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
- Dimensions (inches, HxWxD): 1.75 x 19 x 7.5
- Weight: 2.3 kg
|
- Rated @ 250 V, 16 A
- 16 x 45° angled outlets
- 8 front and 8 rear outlets with individual on/off switches
- Overload protection
The 874716 provides 16 type F grounded outlets in a 19" aluminum enclosure with permanently attached 2 m cord and angled CEE 7/7 power plug. The 1 U rackmount power strip features individual illuminating on/off switches for the 8 front and rear outlets each plus overload protection with individual circuit breakers and reset buttons.
Product type
19" rack mains socket strips
Type
19" / 1 U
Number of outlets (Earthing contact / IEC 7/4)
2 x 8
Power input
cables
Cable length
2 m
Cable connector
angled , Earthing contact (CEE 7/7)
Cross section
1.5 mm²
Operating voltage
250 V
Max. current
16 A
Cabinet material
Aluminium
Colour
Black
Width
485 mm
Height
44 mm
Depth
126 mm
Special feature
8 x Sockets back side , 8 x Sockets front side , Overload protection for front and rear side , Separate front and rear switches
Weight
1,7 kg
|
The most widely recognized and trusted name in AC power conditioning is proud to introduce the PS-PRO E II power conditioner / sequencer, featuring Furman's revolutionary SMP technology. Furman's Series Multi-Stage Protection (SMP) circuit also features our exclusive Linear Filter Technology (LiFT) coupled with Extreme Voltage Shutdown (EVS) and a high current TVZ-MOVs. Together, these technologies comprise what is, without question, the world's most advanced and comprehensive transient voltage surge suppressor. SMP (Series Multi-Stage Protection Plus) Furmanʼs SMP surge suppression virtually eliminates service calls. Traditional surge suppression circuits sacrifice themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. Not so with SMP. With Furmanʼs SMP, damaging transient voltages are safely absorbed, clamped and dissipated - no sacrificed parts, no service calls, no down time. Unique to Furmanʼs SMP is its unparalleled clamping voltage, even when tested beyond the grueling specifications of - USA/CIDAʼs A-1-1 test. While other designs offer clamping voltages that are well above 300VAC peak (far beyond long accepted professional standards), Furmanʼs SMP clamps at 376VAC peak, 266 VAC RMS even when tested with multiple 6000VAC - 3000 Amp surges! This unprecedented level of protection is only available with Furmanʼs SMP technology. LiFT (Linear Filtering Technology) Unfortunately, traditional AC filter/conditioners have been designed for unrealistic laboratory conditions. Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs. Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line! Worse still, lost digital data, the need to reboot digital presets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground. Furmanʼs SMP with LiFT takes another approach, ensuring optimal performance through linear filtering and no leakage to ground. E.V.S. (Extreme Voltage Shutdown) Furmanʼs trusted overvoltage circuitry protects against all too frequent accidental connections to high voltages by shutting off the incoming power until the overvoltage condition is corrected. Rear Panel BNC Connector For rear panel illumination, a BNC connector is provided for connection of any standard gooseneck lamp, such as the Furman GN-LED or GN-I (sold seperately). Sequencing The PS-PRO E II Power Conditioner/Sequencers is capable of powering up a rack full of equipment in a 3- step delayed sequence. The sequence is reversed for power-down. The sequence can be initiated with either momentary or maintained switches, locally or remotely. A duplex outlet is provided for each delay step. A front panel screwdriver adjustment sets the delay time for the PS-PRO E II. The PS-PRO E II also features a locking switch with a removable key for maximum security. One or more Furman PS-PRO II's may be installed in remote locations and operated via low-voltage wiring. Features - SMP provides the highest level of protection available
- LiFT significantly reduces AC line noise
- E.V.S. protects equipment from dangerous overvoltage conditions
- Zero ground contamination circuitry assures delivery of pure AC
- Six sequenced rear panel outlets (in 3 groups), two switched rear panel outlets, and one front panel switched outlet
- Momentary and Maintained sequencing via rear panel terminal block or front panel switch
- 16 amp rating with circuit breaker
- BNC connector on the rear panel allows you to attach any standard 12V gooseneck lamp to illuminate the rear of your rack
- Three year limited warranty
SPECIFICATIONS: Current rating: | 16 amps | Operating Voltage: | 180 to 280 VAC | Over Voltage Shutdown: | 280 VAC typically | Spike Protection Modes: | Line to neutral, zero ground leakage | Spike Clamping Voltage | 376 VAC peak @ 3,000 Amps, 266 VAC RMS (tested to UL-1449 and USA / CIDA A-1-1, 6,000 VAC @ 3,000 Amps) | Response time: | 1 nanosecond | Maximum surge current: | 6,500 amps | Noise attenuation: | 10 dB @ 10 kHz, 40 dB @ 100 kHz, 100 dB @ 10 MHz Linear attenuation curve from 0.05 - 100 Ohms line impedance | Dimensions: | 44.45mm H x 482.6mm W x 266.7mm D. | Weight: | 5 kg. | Construction: | Steel chassis, 3.175mm brushed and black anodized aluminum front panel; glass epoxy printed circuit boards | Power consumption: | 6 watts | Safety Agency Listings: | CE, NRTL-C |
| A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.
SPECIFICATIONS:
Maximum Output Current: |
10 amps |
Line Cord: |
1.5 meter, removable, IEC C-13 female to Schuko male |
Operating Voltage: |
230VAC 50Hz |
Spike Protection Mode: |
Line to neutral |
Energy Dissipation: |
305 joules |
Peak Impulse Current: |
12,000 amps |
Maximum Continuous Opterating Voltage: |
650 Volts |
Noise Attenuation: |
Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz |
Dimensions: |
1.75” H x 19” W x 7.5” D |
Weight: |
2.3 kg. |
Safety Agency Listing: |
CE |
Warranty: |
Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
|
AC Current Capactiy:
Input - 10 Amp capacity required
Output - 10 Amps RMS (both outlets combined)
Linear Noise Attenuation:
> 40 dB @ 100 kHz.
>50 dB @ 500kHz
(Linear attenuation curve from 0.05 to 100 ohms line impedance)
Transient Voltage Surge Suppression:
230 VAC - Series Multi-Stage Protection
Non-Sacrificial with Zero Ground Contamination.
376V peak clamping @ 6000V 3000A input
Extreme Voltage Shutdown (>135 VAC)
Extreme Voltage Shutdown: 275 VAC (Auto-Reset)
Dimensions: 1.75ʼ H x 5ʼ W x 8.5ʼ D
Weight: 3 lbs.
Safety Agency Listing: CE
| The Classic Series from Furman brings together superior protection and outstanding performance in a sturdy, rack-mountable design. The Classic Series features Furmanʼs revolutionary Series Multi-Stage Protection (SMP), Linear Filtering Technology (LiFT), and Extreme Voltage Shutdown (EVS). Together, these technologies comprise what is, without question, one of the world's most advanced and comprehensive transient voltage surge supressors.
SPECIFICATIONS:
Maximum Output Current: |
10 amps |
Line Cord: |
3/1.0MM AWG, 2.5M cord w/IEC female to 10A Schuko plug |
Pull-out Lights: |
Two multi-LED, dimmable lamps |
BNC Socket w/Switch: |
Rear rack lamp, 12VAC 500MA maxx (lamp not included) |
Operating Voltage: |
180 to 274 VAC |
Spike Protection Mode: |
Line to neutral, zero ground leakage |
Spike Clamping Voltage: |
375 VAC peak @ 3,000 Amps |
Response Time: |
1 nanosecond |
Maximum Surge Current: |
6,500 Amps |
Noise Attenuation: |
10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz |
Dimensions: |
482.6mm W x 266.7mm D x 4.45mm H |
Weight: |
6 kg. |
Power Consumption: |
12 watts |
Safety Listing: |
CE |
|
Reviews
There are no reviews yet.