Content |
Furman M10Lx E Power Conditioner form the Merit Series Power Conditioners is the perfect low cost AC power solution for any rack mount system. Install an Furman M10LxE in to the top slot of your rack, and the 10 switched outlets in the rear panel will power up and protect all your equipment up to a 10 amp load. It not only protects anything plugged into it from spikes and surges, but also has a built in AC noise filter to rid the system of RFI / EMI interference.
TheFurman M-10Lx E also features two slide out, swivelling light fixtures to provide discreet illumination of your equipment. A dimmer knob allows the user to adjust the level of illumination. Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.
Features
- AC Noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI)
- Spike & surge protection ensures equipment stays safe and your power stays clean
- 10 rear panel outlets, with front panel convenience outlet
- 10 amp rating, with circuit breaker
- Two retractable LED light fixtures with dimmer control for convenient rack illumination
- Three year warranty
Specification
- Maximum Output Current: 10 amps
- Lamps: LED
- Operating Voltage: 230VAC 50Hz
- Spike Protection Mode: Line to neutral
- Peak Impulse Current: 12,000 amps
- Maximum Continuous Operating Voltage: 650 Volts
- Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
- Dimensions (inches, HxWxD): 1.75 x 19 x 7.5
- Weight: 2.3 kg
|
AC Current Capactiy:
Input - 10 Amp capacity required
Output - 10 Amps RMS (both outlets combined)
Linear Noise Attenuation:
> 40 dB @ 100 kHz.
>50 dB @ 500kHz
(Linear attenuation curve from 0.05 to 100 ohms line impedance)
Transient Voltage Surge Suppression:
230 VAC - Series Multi-Stage Protection
Non-Sacrificial with Zero Ground Contamination.
376V peak clamping @ 6000V 3000A input
Extreme Voltage Shutdown (>135 VAC)
Extreme Voltage Shutdown: 275 VAC (Auto-Reset)
Dimensions: 1.75ʼ H x 5ʼ W x 8.5ʼ D
Weight: 3 lbs.
Safety Agency Listing: CE
|
The most widely recognized and trusted name in AC power conditioning is proud to introduce the PS-8R E II power conditioner / sequencer, featuring Furman's revolutionary SMP technology. Furman's Series Multi-Stage Protection (SMP) circuit also features our exclusive Linear Filter Technology (LiFT) with Extreme Voltage Shutdown (EVS) and a high current TVZ-MOV. Together, these technologies comprise what is, without question, the world's most advanced and comprehensive transient voltage surge suppressor SMP (Series Multi-Stage Protection Plus) Furmanʼs SMP surge suppression virtually eliminates service calls. Traditional surge suppression circuits sacrifice themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. Not so with SMP. With Furmanʼs SMP, damaging transient voltages are safely absorbed, clamped and dissipated - no sacrificed parts, no service calls, no down time. Unique to Furmanʼs SMP is its unparalleled clamping voltage, even when tested beyond the grueling specifications of - USA/CIDAʼs A-1-1 test. While other designs offer clamping voltages that are well above 300VAC peak (far beyond long accepted professional standards), Furmanʼs SMP clamps at 376VAC peak, 266 VAC RMS even when tested with multiple 6000VAC - 3000 Amp surges! This unprecedented level of protection is only available with Furmanʼs SMP technology. LiFT (Linear Filtering Technology) Unfortunately, traditional AC filter/conditioners have been designed for unrealistic laboratory conditions. Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs. Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line! Worse still, lost digital data, the need to reboot digital presets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground. Furmanʼs SMP with LiFT takes another approach, ensuring optimal performance through linear filtering and no leakage to ground. E.V.S. (Extreme Voltage Shutdown) Furmanʼs trusted overvoltage circuitry protects against all too frequent accidental connections to high voltages by shutting off the incoming power until the overvoltage condition is corrected. Rear Panel BNC Connector For rear panel illumination, a BNC connector is provided for connection of any standard gooseneck lamp, such as the Furman GN-LED or GN-I (sold seperately). Sequencing The PS-8R E II Power Conditioner/Sequencers is capable of powering up a rack full of equipment in a 3-step delayed sequence. The sequence is reversed for power-down. The sequence can be initiated with either momentary or maintained switches, locally or remotely. A duplex outlet is provided for each delay step. One or more Furman PS-8R E IIʼs may be installed in remote locations and operated via low-voltage wiring. Features - SMP provides the highest level of protection available
- LiFT significantly reduces AC line noise
- E.V.S. protects equipment from dangerous overvoltage conditions
- Zero ground contamination circuitry assures delivery of pure AC
- Six sequenced rear panel outlets (in 3 groups), two switched rear panel outlets, and one front panel switched outlet
- Momentary and Maintained sequencing via rear panel terminal block or front panel switch
- 10 amp rating with circuit breaker
- BNC connector on the rear panel allows connection of any standard gooseneck lamp
- Three year limited warranty
SPECIFICATIONS: Current rating: | 10 amps | Operating Voltage: | 180 to 280 VAC | Over Voltage Shutdown: | 280 VAC typically | Spike Protection Modes: | Line to neutral, zero ground leakage | Spike Clamping Voltage | 376 VAC peak @ 3,000 Amps, 266 VAC RMS (tested to UL-1449 and USA / CIDA A-1-1, 6,000 VAC @ 3,000 Amps) | Response time: | 1 nanosecond | Maximum surge current: | 6,500 amps | Noise attenuation: | 10 dB @ 10 kHz, 40 dB @ 100 kHz, 100 dB @ 10 MHz Linear attenuation curve from 0.05 - 100 Ohms line impedance | Dimensions: | 44.445mm H x 482.6mm W x 266.7mm D. | Weight: | 5 kg. | Construction: | Steel chassis, 3.175mm brushed and black anodized aluminum front panel; glass epoxy printed circuit boards | Power consumption: | 6 watts | Safety Agency Listings: | CE, NRTL-C |
|
Rack lighting panel with two gooseneck. Dimmer. 12 V. lamps. I
ncludes power supply.
Dimensions: (W x H x D) 482 x 43 x 43 mm.
Weight: 2,5 kgs. | Adam Hall Cables 87471 X7
19" Power Strip 1U 7-way with switch & protection cap
- Mountable Power Strip from our 19" PDU range
- With recessed, illuminated switch and protective cap
- 7 Schuko sockets rotated 45°
- With 8-way adjustable mounting brackets
- 1.4 m PVC cable with angled Schuko plug
The practical solution for your 19" rack. Our 87471 X7 with 8-way adjustable stable mounting ears and 7 Schuko sockets comes with a protective cap for the switch. This prevents the power distributor from being switched off accidentally. The cable routing on the side is supplied with a PVC cable (H05VV-F) with 3 x 1.5 mm² inner conductor and an angled Schuko plug.
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
7, Rotated 45°
Cable connector
angled, Earthing contact (CEE 7/7)
Cabinet material
Aluminium, Plastic
Other features
Illuminated on / off switch with protective cap, Mounting brackets can be inserted in 8 positions
| A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.
SPECIFICATIONS:
Maximum Output Current: |
10 amps |
Line Cord: |
1.5 meter, removable, IEC C-13 female to Schuko male |
Operating Voltage: |
230VAC 50Hz |
Spike Protection Mode: |
Line to neutral |
Energy Dissipation: |
305 joules |
Peak Impulse Current: |
12,000 amps |
Maximum Continuous Opterating Voltage: |
650 Volts |
Noise Attenuation: |
Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz |
Dimensions: |
1.75” H x 19” W x 7.5” D |
Weight: |
2.3 kg. |
Safety Agency Listing: |
CE |
Warranty: |
Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
|
Reviews
There are no reviews yet.