Content |
AC Current Capactiy:
Input - 10 Amp capacity required
Output - 10 Amps RMS (both outlets combined)
Linear Noise Attenuation:
> 40 dB @ 100 kHz.
>50 dB @ 500kHz
(Linear attenuation curve from 0.05 to 100 ohms line impedance)
Transient Voltage Surge Suppression:
230 VAC - Series Multi-Stage Protection
Non-Sacrificial with Zero Ground Contamination.
376V peak clamping @ 6000V 3000A input
Extreme Voltage Shutdown (>135 VAC)
Extreme Voltage Shutdown: 275 VAC (Auto-Reset)
Dimensions: 1.75ʼ H x 5ʼ W x 8.5ʼ D
Weight: 3 lbs.
Safety Agency Listing: CE
| A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.
SPECIFICATIONS:
Maximum Output Current: |
10 amps |
Line Cord: |
1.5 meter, removable, IEC C-13 female to Schuko male |
Operating Voltage: |
230VAC 50Hz |
Spike Protection Mode: |
Line to neutral |
Energy Dissipation: |
305 joules |
Peak Impulse Current: |
12,000 amps |
Maximum Continuous Opterating Voltage: |
650 Volts |
Noise Attenuation: |
Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz |
Dimensions: |
1.75” H x 19” W x 7.5” D |
Weight: |
2.3 kg. |
Safety Agency Listing: |
CE |
Warranty: |
Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
| Adam Hall Cables 87471
19" Power Strip 1U 8-way with switch
Mains Distribution Unit 19"/1 U
- Illuminated 2-pole switch on the front panel
- 8 mains outlets on the rear panel
- Black aluminium housing
- 54 mm deep
- 19 "angle can be mounted in four positions
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
8, Rotated 45°
Cable connector
angled, Earthing contact (CEE 7/7)
Cabinet material
Aluminium, Plastic
Other features
Illuminated on / off switch, Mounting brackets can be used in 4 positions
| Adam Hall Cables 87471 X7
19" Power Strip 1U 7-way with switch & protection cap
- Mountable Power Strip from our 19" PDU range
- With recessed, illuminated switch and protective cap
- 7 Schuko sockets rotated 45°
- With 8-way adjustable mounting brackets
- 1.4 m PVC cable with angled Schuko plug
The practical solution for your 19" rack. Our 87471 X7 with 8-way adjustable stable mounting ears and 7 Schuko sockets comes with a protective cap for the switch. This prevents the power distributor from being switched off accidentally. The cable routing on the side is supplied with a PVC cable (H05VV-F) with 3 x 1.5 mm² inner conductor and an angled Schuko plug.
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
7, Rotated 45°
Cable connector
angled, Earthing contact (CEE 7/7)
Cabinet material
Aluminium, Plastic
Other features
Illuminated on / off switch with protective cap, Mounting brackets can be inserted in 8 positions
|
The Furman PL-PRO DMC is the latest generation of Furman's 16 amp power conditioners, featuring 8 rear-panel mains outlets and one front-panel mains outlet, Furman's exclusive Series Multi-Stage Protection Plus SMP+ with Linear Filtering Technology LiFT and Extreme Voltage Shutdown EVS for ultra-reliable protection of your gear. The PL-PRO DMC also incorporates a USB port on the front panel to allow for the charging of MP3 players and other such devices that can be recharged via USB.
The Furman PL-Pro DMC power conditioner features dimmable LED rack lights that produce virtually no heat and provide an extremely long lifespan. A rear-mounted BNC jack accepts any standard 12VAC, 0.5A gooseneck lamp for rear rack illumination, as well as a front-panel switch which controls the gooseneck's operation. A front-panel mounted master power switch is protected by a hinged cover, preventing accidental disconnection of AC power to the unit's outlets.
The Furman PL-Pro DMC power conditioner has a front-panel digital voltmeter, and the circuit breaker power switch can be easily reset should the unit be overloaded. Portable music players are becoming a staple on live sound gigs and the PL-PRO DMC includes a front-panel USB port for charging and powering of these devices.
Traditional surge suppression circuits "sacrifice" themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. Not so with SMP+. With the Furman PL-PRO DMC's SMP+, damaging transient voltages are safely absorbed, clamped and dissipated. No sacrificed parts, no service calls, no down time.
FURMAN PL-PRO DMC E CLASSIC SERIES POWER CONDITIONER FEATURES
Retractable LED rack lights with on/off/dimmer control.
Isolated outlet banks to minimize inter-component interference and noise contamination.
BNC back panel connector for gooseneck lamp with front-panel switch.
Maintenance-free surge suppression thanks to Series Multi-Stage Protection Plus (SMP+) circuit with extreme voltage shutdown.
8 rear-panel outlets and one front-panel outlet.
LED status indicators warn you when voltage is outside of nominal range or when protection has been compromised.
Front panel USB charger for small USB devices.
Three widely spaced outlets accommodate bulky AC power transformers.
LiFT Linear Filtering Technology with zero ground contamination.
Advanced EVS circuitry detects dangerous voltage irregularities and safely powers down itself and connected equipment in unsafe conditions.
Segmented LED Voltmeter monitors and displays incoming line voltage.
16 amp rating, with high-inrush thermal circuit breaker for added protection.
Two, pull out multi-LED, dimmable lamps.
One rack unit space.
FURMAN PL-PRO DMC E CLASSIC SERIES POWER CONDITIONER SPECIFICATIONS
Maximum Output Current: 16 amps.
Pull-out Lights: Two multi-LED, dimmable lamps.
BNC Socket w/Switch: Rear rack lamp, 12VAC 500mA maxx. Lamp not included.
Operating Voltage: 180 to 274 VAC.
Spike Protection Mode: Line to neutral, zero ground leakage.
Spike Clamping Voltage: 375 VAC peak @ 3,000 Amps.
Maximum Surge Current: 6,500 Amps.
Noise Attenuation: 10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz.
Dimensions (mm, WxHxD): 482.6 x 266.7 x 4.45.
Weight: 6 kg.
Power Consumption: 12 watts.
| Adam Hall Cables 87471 C20
19" Power Strip 1U 8-way with C20 cold device socket
- Power distributor with IEC C20 socket and detachable supply cable included
- Max. current 16 A
- 8 45° rotated Schuko sockets
- Illuminated mains switch
- 250 V operating voltage
Description
Professional and stable 8-way socket strip in 19" format with 1 U. Perfectly suited for installation in racks and the associated power distribution of devices. For a maximum current of 16 A in connection with an IEC cable, there is the IEC C20 connection, which is installed here. The mains cable with IEC C19 on angled Schuko connection and 2 m length is included. The power distributor has an on/off switch at the front and the sockets at the rear are rotated by 45°.
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
8
Cable connector
angled, Earthing contact (CEE 7/7)
Cross section
3 x 1.5 mm² mm²
Cabinet material
Aluminium
Other features
19" rack mains socket strips, Illuminated on / off switch
|
Reviews
There are no reviews yet.