FURMAN M-10x E Power Conditioner

160.00 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load. SPECIFICATIONS: Maximum Output Current: […]

 

Read more

A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.

SPECIFICATIONS:

Maximum Output Current: 10 amps
Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male
Operating Voltage: 230VAC 50Hz
Spike Protection Mode: Line to neutral
Energy Dissipation: 305 joules
Peak Impulse Current: 12,000 amps
Maximum Continuous Opterating Voltage: 650 Volts
Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
Dimensions: 1.75” H x 19” W x 7.5” D
Weight: 2.3 kg.
Safety Agency Listing: CE
Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.
Weight 2.30 kg

Reviews

There are no reviews yet.

Be the first to review “FURMAN M-10x E Power Conditioner”

Your email address will not be published. Required fields are marked *

Quick Comparison

FURMAN M-10x E Power Conditioner removeWORK D-9-P-1U LIGHTING UNIT removeWORK D-2 RACK LIGHTING PANEL w-DIMMER removeFURMAN P2300IT-E SYMMETRICALLY BALANCED POWER CONDITIONER removeAdam Hall 87471 C20 19" Power Strip 8-way With Cold Device Socket 1U removeAdam Hall 87471 X7-way Out Power Strip 1U Switch Protection Cap remove
NameFURMAN M-10x E Power Conditioner removeWORK D-9-P-1U LIGHTING UNIT removeWORK D-2 RACK LIGHTING PANEL w-DIMMER removeFURMAN P2300IT-E SYMMETRICALLY BALANCED POWER CONDITIONER removeAdam Hall 87471 C20 19" Power Strip 8-way With Cold Device Socket 1U removeAdam Hall 87471 X7-way Out Power Strip 1U Switch Protection Cap remove
Image87471C20_power distributor c20 cold socket 8way out87471x7_power distributor 7way out switch quard-2
SKUM10xED-9D-2P2300ITE87471C2087471X7
Rating
Price160.00 incl. GR VAT 84.00 incl. GR VAT 82.00 incl. GR VAT3,222.38 incl. GR VAT 59.52 incl. GR VAT 43.39 incl. GR VAT
Stock

Available on backorder

In stock

Available on backorder

Available on backorder

Available on backorder

Available on backorder

AvailabilityAvailable on backorderIn stockAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentA Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load. SPECIFICATIONS:
Maximum Output Current: 10 amps
Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male
Operating Voltage: 230VAC 50Hz
Spike Protection Mode: Line to neutral
Energy Dissipation: 305 joules
Peak Impulse Current: 12,000 amps
Maximum Continuous Opterating Voltage: 650 Volts
Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
Dimensions: 1.75” H x 19” W x 7.5” D
Weight: 2.3 kg.
Safety Agency Listing: CE
Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.

Lighting unit for rack 19?. Eight mains outputs (IEC connector) with independent switch and
individual filter. Adjustable lighting level.

Rack lighting panel with two gooseneck. Dimmer. 12 V. lamps. I
ncludes power supply.
Dimensions: (W x H x D) 482 x 43 x 43 mm.
Weight: 2,5 kgs.

Designed for the most critical, ultra-low noise installations, the P-2300 IT E supplies up to 10 amps of balanced AC power ideal for recording studios, broadcast stations, video production facilities, or any environment requiring a pristine, studio-quality signal-to-noise ratio.

The P-2300 IT E features a specially wound and shielded toroidal balanced isolation transformer specifically designed to reduce hum pickup by sensitive equipment when ultra-low-noise is a must. Additionally, Furmanʼs revolutionary Series Multi-Stage Protection (SMP), Extreme Voltage Shutdown (EVS), and Linear Filtering Technology (LiFT) are combined to ensure what our customers have grown to expect from Furman — uncompromised protection and purification.

Symmetrically Balanced Power
Furmanʼs Symmetrically Balanced Power provides a virtually invisible noise floor by reworking incoming AC into a balanced power output. Similar to a balanced audio signal, balanced power splits a single voltage path into two separate voltage paths which are in opposite polarity, cancelling out noise and distortion on the incoming line. This noise reduction is extraordinarily efficient and linear across a huge frequency range, unveiling harmonics, overtones and low-level signals commonly masked by AC line noise.

Unmatched Protection
Furmanʼs SMP and EVS circuitry safeguards equipment from transient voltage events (such as surges and spikes), as well as sustained overvoltage conditions (commonly caused by wiring faults), for complete and comprehensive protection of sensitive equipment.

Innovative Convenience and Monitoring Features
The P-2300 IT Eʼs front panel LED window displays incoming voltage or output current, with ”Protection OK”, ”Extreme Voltage” and color-coded ”Voltage Range” indicators for comprehensive power monitoring. A front panel USB outlet charges most personal media devices and cell phones right at your equipment rack. Universal IEC C-13 receptacles (12 rear panel, 2 front panel) and a removable power cord ensure compatibility with regional power requirements.

SPECIFICATIONS:

Maximum Current:10 amps
Line Cord:Detachable cord, 1mm² x 3, 2.5M long, Schuko plug to IEC C13
Operating Voltage:180 to 244 VAC, 50 Hz
Over-Voltage Shutdown:275 VAC Nominal
Spike Protection Mode:Line to neutral, zero ground leakage
Spike Clamping Voltage:375 VAC peak @ 3,000 Amps
Response Time:1 nanosecond
Maximum Surge Current:6,500 Amps
Noise Attenuation:10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz
Dimensions:483mm W x 356mm D x 133mm H (19” W x 14” D x 5.25” H)
Weight:43 kg. (95lbs.)
Power Consumption:18 watts (for display and control circuits)
Receptacles:Fourteen IEC C-13 (two front panel, twelve rear panel)

 

Adam Hall Cables 87471 C20

19" Power Strip 1U 8-way with C20 cold device socket

  • Power distributor with IEC C20 socket and detachable supply cable included
  • Max. current 16 A
  • 8 45° rotated Schuko sockets
  • Illuminated mains switch
  • 250 V operating voltage

Description

Professional and stable 8-way socket strip in 19" format with 1 U. Perfectly suited for installation in racks and the associated power distribution of devices. For a maximum current of 16 A in connection with an IEC cable, there is the IEC C20 connection, which is installed here. The mains cable with IEC C19 on angled Schuko connection and 2 m length is included. The power distributor has an on/off switch at the front and the sockets at the rear are rotated by 45°.

Product type
19" rack mains socket strips
Type
19" / 1 U
Number of outlets (Earthing contact / IEC 7/4)
8
Power input
cables
Cable length
2 m
Cable connector
angled, Earthing contact (CEE 7/7)
Cross section
3 x 1.5 mm² mm²
cable type
H05VV-F
Operating voltage
250 V
Max. current
16 A A
Cabinet material
Aluminium
Color
Black
Width
485 mm
Height
44 mm
Depth
44 mm
Other features
19" rack mains socket strips, Illuminated on / off switch
Weight
0,73 kg

Adam Hall Cables 87471 X7

19" Power Strip 1U 7-way with switch & protection cap

  • Mountable Power Strip from our 19" PDU range
  • With recessed, illuminated switch and protective cap
  • 7 Schuko sockets rotated 45°
  • With 8-way adjustable mounting brackets
  • 1.4 m PVC cable with angled Schuko plug

The practical solution for your 19" rack. Our 87471 X7 with 8-way adjustable stable mounting ears and 7 Schuko sockets comes with a protective cap for the switch. This prevents the power distributor from being switched off accidentally. The cable routing on the side is supplied with a PVC cable (H05VV-F) with 3 x 1.5 mm² inner conductor and an angled Schuko plug.

Product type
19" rack mains socket strips
Type
19" / 1 U
Number of outlets (Earthing contact / IEC 7/4)
7, Rotated 45°
Power input
cables
Cable length
2 m
Cable connector
angled, Earthing contact (CEE 7/7)
Cross section
1.5 mm²
Operating voltage
250 V
Max. current
16 A
Cabinet material
Aluminium, Plastic
Color
Black
Width
482.6 mm
Height
45 mm
Depth
44.6 mm
Other features
Illuminated on / off switch with protective cap, Mounting brackets can be inserted in 8 positions
Weight
0,9 kg
Weight2.30 kg3.00 kg2.50 kg43.00 kg1 kg1 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 2.30 kg
Weight 3.00 kg
Weight 2.50 kg
Weight 43.00 kg
Weight 1 kg
Weight 1 kg