FURMAN M-10x E Power Conditioner

160.00 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load. SPECIFICATIONS: Maximum Output Current: […]

 

Read more

A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.

SPECIFICATIONS:

Maximum Output Current: 10 amps
Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male
Operating Voltage: 230VAC 50Hz
Spike Protection Mode: Line to neutral
Energy Dissipation: 305 joules
Peak Impulse Current: 12,000 amps
Maximum Continuous Opterating Voltage: 650 Volts
Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
Dimensions: 1.75” H x 19” W x 7.5” D
Weight: 2.3 kg.
Safety Agency Listing: CE
Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.
Weight 2.30 kg

Reviews

There are no reviews yet.

Be the first to review “FURMAN M-10x E Power Conditioner”

Your email address will not be published. Required fields are marked *

Quick Comparison

FURMAN M-10x E Power Conditioner removeFURMAN PS-PRO E II POWER CONDITIONER/SEQUENCER removeWORK D-2 RACK LIGHTING PANEL w-DIMMER removeFURMAN P1400AR-E VOLTAGE REGULATOR / POWER CONDITIONER removeWORK D-9-P-1U LIGHTING UNIT removeFURMAN PL-8 C E POWER CONDITIONER remove
NameFURMAN M-10x E Power Conditioner removeFURMAN PS-PRO E II POWER CONDITIONER/SEQUENCER removeWORK D-2 RACK LIGHTING PANEL w-DIMMER removeFURMAN P1400AR-E VOLTAGE REGULATOR / POWER CONDITIONER removeWORK D-9-P-1U LIGHTING UNIT removeFURMAN PL-8 C E POWER CONDITIONER remove
Image
SKUM10xEPSPROEIID-2P1400ARED-9PL8CE
Rating
Price160.00 incl. GR VAT564.20 incl. GR VAT 81.93 incl. GR VAT1,331.50 incl. GR VAT 84.00 incl. GR VAT439.00 incl. GR VAT
Stock

Available on backorder

Available on backorder

Available on backorder

Available on backorder

In stock

Available on backorder

AvailabilityAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderIn stockAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentA Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load. SPECIFICATIONS:
Maximum Output Current: 10 amps
Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male
Operating Voltage: 230VAC 50Hz
Spike Protection Mode: Line to neutral
Energy Dissipation: 305 joules
Peak Impulse Current: 12,000 amps
Maximum Continuous Opterating Voltage: 650 Volts
Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
Dimensions: 1.75” H x 19” W x 7.5” D
Weight: 2.3 kg.
Safety Agency Listing: CE
Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.

The most widely recognized and trusted name in AC power conditioning is proud to introduce the PS-PRO E II power conditioner / sequencer, featuring Furman's revolutionary SMP technology. Furman's Series Multi-Stage Protection (SMP) circuit also features our exclusive Linear Filter Technology (LiFT) coupled with Extreme Voltage Shutdown (EVS) and a high current TVZ-MOVs. Together, these technologies comprise what is, without question, the world's most advanced and comprehensive transient voltage surge suppressor.

SMP (Series Multi-Stage Protection Plus)
Furmanʼs SMP surge suppression virtually eliminates service calls. Traditional surge suppression circuits sacrifice themselves when exposed to multiple transient voltage spikes, requiring the dismantling of your system, and repair of your surge suppressor. Not so with SMP. With Furmanʼs SMP, damaging transient voltages are safely absorbed, clamped and dissipated - no sacrificed parts, no service calls, no down time.

Unique to Furmanʼs SMP is its unparalleled clamping voltage, even when tested beyond the grueling specifications of - USA/CIDAʼs A-1-1 test. While other designs offer clamping voltages that are well above 300VAC peak (far beyond long accepted professional standards), Furmanʼs SMP clamps at 376VAC peak, 266 VAC RMS even when tested with multiple 6000VAC - 3000 Amp surges! This unprecedented level of protection is only available with Furmanʼs SMP technology.

LiFT (Linear Filtering Technology)
Unfortunately, traditional AC filter/conditioners have been designed for unrealistic laboratory conditions. Prior technologies could actually harm audio and video performance more than they help, due to the resonant peaking of their antiquated, non-linear designs. Under certain conditions, these designs can actually add more than 10 dB of noise to the incoming AC line! Worse still, lost digital data, the need to reboot digital presets, or destroyed digital converters are frequently caused by excessive voltage spikes and AC noise contaminating the equipment ground. Furmanʼs SMP with LiFT takes another approach, ensuring optimal performance through linear filtering and no leakage to ground.

E.V.S. (Extreme Voltage Shutdown)
Furmanʼs trusted overvoltage circuitry protects against all too frequent accidental connections to high voltages by shutting off the incoming power until the overvoltage condition is corrected.

Rear Panel BNC Connector
For rear panel illumination, a BNC connector is provided for connection of any standard gooseneck lamp, such as the Furman GN-LED or GN-I (sold seperately).

Sequencing
The PS-PRO E II Power Conditioner/Sequencers is capable of powering up a rack full of equipment in a 3- step delayed sequence. The sequence is reversed for power-down. The sequence can be initiated with either momentary or maintained switches, locally or remotely. A duplex outlet is provided for each delay step. A front panel screwdriver adjustment sets the delay time for the PS-PRO E II. The PS-PRO E II also features a locking switch with a removable key for maximum security. One or more Furman PS-PRO II's may be installed in remote locations and operated via low-voltage wiring.

Features
  • SMP provides the highest level of protection available
  • LiFT significantly reduces AC line noise
  • E.V.S. protects equipment from dangerous overvoltage conditions
  • Zero ground contamination circuitry assures delivery of pure AC
  • Six sequenced rear panel outlets (in 3 groups), two switched rear panel outlets, and one front panel switched outlet
  • Momentary and Maintained sequencing via rear panel terminal block or front panel switch
  • 16 amp rating with circuit breaker
  • BNC connector on the rear panel allows you to attach any standard 12V gooseneck lamp to illuminate the rear of your rack
  • Three year limited warranty

SPECIFICATIONS:

Current rating:16 amps
Operating Voltage:180 to 280 VAC
Over Voltage Shutdown:280 VAC typically
Spike Protection Modes:Line to neutral, zero ground leakage
Spike Clamping Voltage376 VAC peak @ 3,000 Amps, 266 VAC RMS
(tested to UL-1449 and USA / CIDA A-1-1, 6,000 VAC @ 3,000 Amps)
Response time:1 nanosecond
Maximum surge current:6,500 amps
Noise attenuation:10 dB @ 10 kHz, 40 dB @ 100 kHz, 100 dB @ 10 MHz
Linear attenuation curve from 0.05 - 100 Ohms line impedance
Dimensions:44.45mm H x 482.6mm W x 266.7mm D.
Weight:5 kg.
Construction:Steel chassis, 3.175mm brushed and black anodized aluminum front panel; glass epoxy printed circuit boards
Power consumption:6 watts
Safety Agency Listings:CE, NRTL-C

Rack lighting panel with two gooseneck. Dimmer. 12 V. lamps. I
ncludes power supply.
Dimensions: (W x H x D) 482 x 43 x 43 mm.
Weight: 2,5 kgs.

The 6 Amp P-1400 AR E delivers a stable 230 volts of AC power to protect equipment from problems caused by AC line voltage irregularities such as sags, brownouts, or overvoltages - all of which can cause sensitive electronic equipment to malfunction or sustain damage. The P-1400 AR E accepts any input voltage from 188V to 270V and transforms it to a constant output of 230V or 240V (switchable), ±10V. Voltages beyond that range may also be converted to usable levels, depending on the range variance.

Additionally, the P-1400 AR E is a full-featured power conditioner that filters and purifies AC power, reducing line noise and ensuring optimum performance. Not only will your equipment perform better with Furmanʼs Linear Filtering Technology (LiFT), but it will also be fully protected by our exclusive Series Multi-Stage Protection (SMP), and Extreme Voltage Shutdown (EVS). This circuitry provides the highest level of power protection available.

Maximum Current: 6 amps
Line Cord: Captive AWG, 2.5M black cord with IEC Female to Schuko plug
BNC Socket w/Switch: 12VAC 500MA maxx (lamp not included)
Operating Voltage: 170 to 274 VAC
Over-Voltage Shutdown: 275 VAC Nominal
Approximate Input Voltage Capture Range: 174 to 264 VAC
Spike Protection Mode: Line to neutral, zero ground leakage
Spike Clamping Voltage: 375 VAC peak @ 3,000 Amps
Response Time: 1 nanosecond
Maximum Surge Current: 6,500 Amps
Noise Attenuation: 10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz
Dimensions: 19” W x 12” D x 1.75” H (483mm W x 305mm D x 45mm H)
Weight: 7 kg.
Power Consumption: 5 watts

SPECIFICATIONS:

Maximum Current: 6 amps
Line Cord: Captive AWG, 2.5M black cord with IEC Female to Schuko plug
BNC Socket w/Switch: 12VAC 500MA maxx (lamp not included)
Operating Voltage: 170 to 274 VAC
Over-Voltage Shutdown: 275 VAC Nominal
Approximate Input Voltage Capture Range: 174 to 264 VAC
Spike Protection Mode: Line to neutral, zero ground leakage
Spike Clamping Voltage: 375 VAC peak @ 3,000 Amps
Response Time: 1 nanosecond
Maximum Surge Current: 6,500 Amps
Noise Attenuation: 10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz
Dimensions: 19” W x 12” D x 1.75” H (483mm W x 305mm D x 45mm H)
Weight: 7 kg.
Power Consumption: 5 watts

Lighting unit for rack 19?. Eight mains outputs (IEC connector) with independent switch and
individual filter. Adjustable lighting level.

The Classic Series from Furman brings together superior protection and outstanding performance in a sturdy, rack-mountable design. The Classic Series features Furmanʼs revolutionary Series Multi-Stage Protection (SMP), Linear Filtering Technology (LiFT), and Extreme Voltage Shutdown (EVS). Together, these technologies comprise what is, without question, one of the world's most advanced and comprehensive transient voltage surge supressors. SPECIFICATIONS:
Maximum Output Current: 10 amps
Line Cord: 3/1.0MM AWG, 2.5M cord w/IEC female to 10A Schuko plug
Pull-out Lights: Two multi-LED, dimmable lamps
BNC Socket w/Switch: Rear rack lamp, 12VAC 500MA maxx (lamp not included)
Operating Voltage: 180 to 274 VAC
Spike Protection Mode: Line to neutral, zero ground leakage
Spike Clamping Voltage: 375 VAC peak @ 3,000 Amps
Response Time: 1 nanosecond
Maximum Surge Current: 6,500 Amps
Noise Attenuation: 10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz
Dimensions: 482.6mm W x 266.7mm D x 4.45mm H
Weight: 6 kg.
Power Consumption: 12 watts
Safety Listing: CE
Weight2.30 kg5.00 kg2.50 kg7.00 kg3.00 kg6.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 2.30 kg
Weight 5.00 kg
Weight 2.50 kg
Weight 7.00 kg
Weight 3.00 kg
Weight 6.00 kg