Content | A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.
SPECIFICATIONS:
Maximum Output Current: |
10 amps |
Line Cord: |
1.5 meter, removable, IEC C-13 female to Schuko male |
Operating Voltage: |
230VAC 50Hz |
Spike Protection Mode: |
Line to neutral |
Energy Dissipation: |
305 joules |
Peak Impulse Current: |
12,000 amps |
Maximum Continuous Opterating Voltage: |
650 Volts |
Noise Attenuation: |
Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz |
Dimensions: |
1.75” H x 19” W x 7.5” D |
Weight: |
2.3 kg. |
Safety Agency Listing: |
CE |
Warranty: |
Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
|
AC Current Capactiy:
Input - 10 Amp capacity required
Output - 10 Amps RMS (both outlets combined)
Linear Noise Attenuation:
> 40 dB @ 100 kHz.
>50 dB @ 500kHz
(Linear attenuation curve from 0.05 to 100 ohms line impedance)
Transient Voltage Surge Suppression:
230 VAC - Series Multi-Stage Protection
Non-Sacrificial with Zero Ground Contamination.
376V peak clamping @ 6000V 3000A input
Extreme Voltage Shutdown (>135 VAC)
Extreme Voltage Shutdown: 275 VAC (Auto-Reset)
Dimensions: 1.75ʼ H x 5ʼ W x 8.5ʼ D
Weight: 3 lbs.
Safety Agency Listing: CE
|
Furman M10Lx E Power Conditioner form the Merit Series Power Conditioners is the perfect low cost AC power solution for any rack mount system. Install an Furman M10LxE in to the top slot of your rack, and the 10 switched outlets in the rear panel will power up and protect all your equipment up to a 10 amp load. It not only protects anything plugged into it from spikes and surges, but also has a built in AC noise filter to rid the system of RFI / EMI interference.
TheFurman M-10Lx E also features two slide out, swivelling light fixtures to provide discreet illumination of your equipment. A dimmer knob allows the user to adjust the level of illumination. Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.
Features
- AC Noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI)
- Spike & surge protection ensures equipment stays safe and your power stays clean
- 10 rear panel outlets, with front panel convenience outlet
- 10 amp rating, with circuit breaker
- Two retractable LED light fixtures with dimmer control for convenient rack illumination
- Three year warranty
Specification
- Maximum Output Current: 10 amps
- Lamps: LED
- Operating Voltage: 230VAC 50Hz
- Spike Protection Mode: Line to neutral
- Peak Impulse Current: 12,000 amps
- Maximum Continuous Operating Voltage: 650 Volts
- Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
- Dimensions (inches, HxWxD): 1.75 x 19 x 7.5
- Weight: 2.3 kg
| Adam Hall Cables 87471 C20
19" Power Strip 1U 8-way with C20 cold device socket
- Power distributor with IEC C20 socket and detachable supply cable included
- Max. current 16 A
- 8 45° rotated Schuko sockets
- Illuminated mains switch
- 250 V operating voltage
Description
Professional and stable 8-way socket strip in 19" format with 1 U. Perfectly suited for installation in racks and the associated power distribution of devices. For a maximum current of 16 A in connection with an IEC cable, there is the IEC C20 connection, which is installed here. The mains cable with IEC C19 on angled Schuko connection and 2 m length is included. The power distributor has an on/off switch at the front and the sockets at the rear are rotated by 45°.
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
8
Cable connector
angled, Earthing contact (CEE 7/7)
Cross section
3 x 1.5 mm² mm²
Cabinet material
Aluminium
Other features
19" rack mains socket strips, Illuminated on / off switch
|
- Rated @ 250 V, 16 A
- 16 x 45° angled outlets
- 8 front and 8 rear outlets with individual on/off switches
- Overload protection
The 874716 provides 16 type F grounded outlets in a 19" aluminum enclosure with permanently attached 2 m cord and angled CEE 7/7 power plug. The 1 U rackmount power strip features individual illuminating on/off switches for the 8 front and rear outlets each plus overload protection with individual circuit breakers and reset buttons.
Product type
19" rack mains socket strips
Type
19" / 1 U
Number of outlets (Earthing contact / IEC 7/4)
2 x 8
Power input
cables
Cable length
2 m
Cable connector
angled , Earthing contact (CEE 7/7)
Cross section
1.5 mm²
Operating voltage
250 V
Max. current
16 A
Cabinet material
Aluminium
Colour
Black
Width
485 mm
Height
44 mm
Depth
126 mm
Special feature
8 x Sockets back side , 8 x Sockets front side , Overload protection for front and rear side , Separate front and rear switches
Weight
1,7 kg
|
Lighting unit for rack 19?. Eight mains outputs (IEC connector) with independent switch and
individual filter. Adjustable lighting level. |
Reviews
There are no reviews yet.