Content |
The small Genelec 4020B shares same superior design with Genelec 8000-series active monitoring loudspeakers. 4020B has been designed for challenging commercial installations, particularly those compromised by lack of space.
Our Intelligent Signal Sensing (ISS) feature, reduces power consumption to less than 0.5 watts by automatically switching the active monitor to standby, when no audio signal has been detected for some time. When it receives an audio signal again, the loudspeaker turns back on.
ISS is fully compliant with the latest EU requirements and the ErP 2013 Directive for electronic devices.
| 95 dB | | 66 Hz - 20 kHz (± 2.5 dB)
65 Hz - 21 kHz (-3 dB) | | 3.0 kHz | | Bass 4" + Treble 3/4“
metal dome + DCWTM | | Bass 20 W + Treble 20 W | | H x W x D 226 x 151 x 142 mm | | 3.6 Kg (7.9 lb) | | 1 x balanced Phoenix connector |
|
The new J series is a technologically advanced range of products that improves on the performance of the previous Jolly line. The new J series is a competitive, value for money range of speakers. The range is based on the development of three new high efficiency class-D amplifiers with power specifications of 350 + 100W for the J 15A & J 12A, 200 + 50W for the J 8A and 80 + 40W for the J 5A.
These amplifiers have been designed 'from the ground up' in FBT’s R&D laboratories. The largest amplifier model that equips the J 15A and J 12A has a switch mode power supply as well as a digital signal processor with 4 pre-sets.
The J 8A and J 5A amplifiers have toroidal transformer power supplies. The J 8A has a digital signal processor with 2 pre-sets, whilst the J 5A has analog signal processing.
The speakers have been completely redesigned, introducing the technological developments of recent years to achieve a far superior efficiency and linearity.
Following from the new J series, FBT bring you the DJ 15A, designed with today’s modern DJ in mind. The DJ 15A has invaluable features allowing quality audio playback using our revolutionary DSP technology. This includes 4 presets enabling the DJ to change the sound of their music to suit the environment they play within.
These DSP presets will allow the DJs audience to enjoy improved sound quality and SPL, especially in bass reproduction at high volume.
The DJ 15A also has another useful feature for DJs, including a two channel input mixer allowing the DJ to plug a music source and microphone direct into the speaker, giving separate control over volume for both devices. You can also daisy chain these speaker together if required. Ideal for many application of today’s modern DJ.
Code: |
37687 / 37905 White |
Configuration: |
2 way |
Built-in amplifier LF/HF: |
80/40 W RMS |
Built-in amplifier peak LF/HF: |
160/80 W |
Frequency response: |
80Hz - 20KHz -6dB |
Low Frequency woofer: |
5 - 1 coil inch |
High Frequency driver: |
1 dome - 0.75 coil inch |
Maximum SPL cont/peak: |
113 / 117 dB |
Dispersion: |
90° x 90° HxV |
Input impedance: |
22 Kohm |
Crossover Frequency: |
3.5 KHz |
AC Power requirements: |
75 VA |
Input connector: |
XLR combo with loop |
Power cord: |
5 / 16.4 m/ft |
Net Dimension (WxHxD): |
170x275x180 - 6.69x10.82x7.08 mm/inch |
Net Weight: |
3.4 / 7.49 Kg/lb |
Transport Dimension (WxHxD): |
240x345x235 - 9.44x13.58x9.25 mm/inch |
Transport Weight: |
4.2 / 9.25 Kg/lb |
| The LD Systems SAT62AG2 is the active version of the SAT62G2. The compact 2-way speaker is not only suitable for installation, but also as a home studio monitor and for other sound reinforcement tasks.
The bass-reflex design is loaded with a 6.5" custom woofer and a 1" silk dome tweeter with wave guide, which are driven by a Class AB power amplifier with 50 W continuous power and overcurrent protection. The input is a XLR-jack combo socket, an XLR socket permits looping through of the signal. Reproduction is balanced and dynamic throughout the frequency range of 55 Hz - 20 kHz and attains a maximum sound-level pressure of 108 dB. The SAT62AG2 features a switchable power saving mode that automatically switches to standby if there is no signal for 3 minutes.
The 12 mm MDF cabinet with a durable textured coating is available in black and white and equipped with M6 rigging points. An included mounting bracket offers additional possibilities for mounting; a universal joint mount is available as an accessory.
Specifications 6,5" Installation Monitor Active:
- Model Name: LDSAT62AG2
- Type: Bass Reflex
- Components:
- Woofer: 6,5" Custom Made
- Compression Driver: 1" Custom Made
- Amplification: Class A / B
- Dispersion: 60° x 60°
- Power (RMS): 50 W
- Frequency Range: 55 Hz - 20 kHz
- SPL (1 W / 1 m): 89 dB
- Max SPL: 108 dB
- Protection: Over-current
- Controls: Volume, Switchable Auto / Power Mode
- Indicators: Power
- Connectors:
- Input: Line: XLR + Jack 6,3 mm Combo
- Output: Line: XLR
- Cabinet Material: 12 mm MDF
- Cabinet Surface: Painting
- Dimensions (W x H x D): 200 x 410 x 243 mm
- Additional features: M6 rigging / mounting points, mounting brackets
|
Comprising four versatile loudspeaker enclosures for either portable use or fixed installation, FBT is debuting the VENTIS range at Pro Light + Sound 2016. Available in either passive or bi-amplified versions, each of the models – the VENTIS 115, 112, 110, and 206 – has been designed to meet the highest standards in both performance and aesthetic appeal.
For the VENTIS range, quality and flexibility are the watchwords. Based on a powerful combination of B&C compression drivers and FBT’s own custom, long excursion woofers, the 115, 112 and 110 models are two-way, bass reflex designs housed in 15mm birch plywood. A full-grille design backed by specially treated acoustic cloth delivers the characteristic style for which FBT is known, while fully rotatable constant directivity horns ensure accurate coverage.
The three enclosures are as suitable for fixed installation as they are for use on the stage. M10 points are included as standard while an optional U-bracket can be used for wall-mounting. For use on the road, the VENTIS models include aluminum handles with rubber inserts, a 35mm polemount socket, and a 45° sloped profile for unobtrusive placement on-stage as a monitor.
Meanwhile the multi-purpose VENTIS 206 can be deployed as a front fill, an under-balcony fill, as a main providing pristine speech intelligibility or simply as the full-range companion of a subwoofer. Constructed in 12mm birch plywood, the 206 has an integrated rear handle, an optional mounting bracket and, most importantly, an astonishing size to SPL ratio.
Power for the active VENTIS models comes courtesy of a specially designed, Italian made switching mode amplifier module. Low frequencies are driven by a highly efficient 700W RMS (full bridge) Class-D topology, operating with extremely low THD. For the HF stage, a 200W RMS performance is delivered via a meticulously crafted Class-H / AB design.
Finally, DSP on-board the VENTIS enclosures is both user friendly and powerful. Located on the rear of each enclosure, a menu-driven system is navigated via a single rotary control with push-to-select functionality. A total of 6 pre-optimised settings are available (see below), plus 2 further slots for users to form their own designs, using 5 parametric equalizers per slot. Also available is a high-pass filter, a mic/line selector, low, mid and high tone settings and an optional delay of between 0 and 3.5 metres. Finally, users can exclusively choose between two limiter modes, MAX-SPL or MAX-QUALITY, to best suit their performance.
- 2-way, bi-amplified, bass reflex design
- Biamped: 700W RMS LF and 200W RMS HF power amplifiers in Class D for LF and in Class H/AB for HF
- Digital Signal Processor with graphic display
- 15 mm (0.59”) birch plywood scratch resistant enclosure and internal bracing
- High efficiency switch mode power supply
- Control Panel features balanced XLR/Jack input, XLR LINK OUT, 2 x Volume, RCA Stereo input, DSP display with rotative encoder and push
- 2x165mm (6.5”) LF woofer with 38mm (1.5”) voice coil, custom made for FBT
- 25mm (1”) exit throat B&C HF compression driver with 36mm (1.4”) voice coil
- Frequency response from 70Hz to 20 kHz
- 70°H x 50°V Constant Directivity Rotatable Horn
- 6 x M10 suspension points, wall bracket mount thread, 35mm (1 3/8”) top-hat
- One integrated handle
- 12mm (0.47”) birch plywood scratch resistant enclosure and internal bracing
Code: |
40639 |
Configuration: |
2 way |
Built-in amplifier LF/HF: |
700/200 W RMS |
Built-in amplifier peak LF/HF: |
1400/400 W |
Frequency response: |
70Hz - 20KHz -6dB |
Low Frequency woofer: |
2x6.5 - 1.5 coil inch |
High Frequency driver: |
1 - 1.4 coil inch |
Maximum SPL cont/peak: |
124/131 dB |
Dispersion: |
70° x 50° rotatable HxV |
Input impedance: |
640 Kohm |
AC Power requirements: |
640 VA |
Input connector: |
XLR with loop, RCA ST |
Power cord: |
5/16.4 m/ft |
Net Dimension (WxHxD): |
190x560x260 / 7.48x22.04x10.23 mm/inch |
Net Weight: |
12.3/27.11 Kg/lb |
Transport Dimension (WxHxD): |
290x660x360 / 11.41x25.98x14.17 mm/inch |
Transport Weight: |
14.3/31.52 Kg/lb |
|
The new J series is a technologically advanced range of products that improves on the performance of the previous Jolly line. The new J series is a competitive, value for money range of speakers. The range is based on the development of three new high efficiency class-D amplifiers with power specifications of 350 + 100W for the J 15A & J 12A, 200 + 50W for the J 8A and 80 + 40W for the J 5A.
These amplifiers have been designed 'from the ground up' in FBT’s R&D laboratories. The largest amplifier model that equips the J 15A and J 12A has a switch mode power supply as well as a digital signal processor with 4 pre-sets.
The J 8A and J 5A amplifiers have toroidal transformer power supplies. The J 8A has a digital signal processor with 2 pre-sets, whilst the J 5A has analog signal processing.
The speakers have been completely redesigned, introducing the technological developments of recent years to achieve a far superior efficiency and linearity.
Following from the new J series, FBT bring you the DJ 15A, designed with today’s modern DJ in mind. The DJ 15A has invaluable features allowing quality audio playback using our revolutionary DSP technology. This includes 4 presets enabling the DJ to change the sound of their music to suit the environment they play within.
These DSP presets will allow the DJs audience to enjoy improved sound quality and SPL, especially in bass reproduction at high volume.
The DJ 15A also has another useful feature for DJs, including a two channel input mixer allowing the DJ to plug a music source and microphone direct into the speaker, giving separate control over volume for both devices. You can also daisy chain these speaker together if required. Ideal for many application of today’s modern DJ.
Code: |
37687 / 37905 White |
Configuration: |
2 way |
Built-in amplifier LF/HF: |
80/40 W RMS |
Built-in amplifier peak LF/HF: |
160/80 W |
Frequency response: |
80Hz - 20KHz -6dB |
Low Frequency woofer: |
5 - 1 coil inch |
High Frequency driver: |
1 dome - 0.75 coil inch |
Maximum SPL cont/peak: |
113 / 117 dB |
Dispersion: |
90° x 90° HxV |
Input impedance: |
22 Kohm |
Crossover Frequency: |
3.5 KHz |
AC Power requirements: |
75 VA |
Input connector: |
XLR combo with loop |
Power cord: |
5 / 16.4 m/ft |
Net Dimension (WxHxD): |
170x275x180 - 6.69x10.82x7.08 mm/inch |
Net Weight: |
3.4 / 7.49 Kg/lb |
Transport Dimension (WxHxD): |
240x345x235 - 9.44x13.58x9.25 mm/inch |
Transport Weight: |
4.2 / 9.25 Kg/lb |
|
The very compact 4030B is a powerful bi-amplified speaker system ideal for small to mid-sized commercial installations such as clubs, bars, board rooms, museums, theaters, etc.
Our Intelligent Signal Sensing (ISS) feature, reduces power consumption to less than 0.5 watts by automatically switching the active monitor to standby, when no audio signal has been detected for some time. When it receives an audio signal again, the loudspeaker turns back on.
ISS is fully compliant with the latest EU requirements and the ErP 2013 Directive for electronic devices.
The MDETM (Minimum Diffraction EnclosureTM) enclosure has rounded edges and a gently curved front and sides to achieve a very smooth frequency response and superb imaging qualities with minimized cabinet edge diffraction.
The 4030B also features the advanced Genelec Directivity Control WaveguideTM (DCWTM), a revolutionary flow-optimized reflex port design, optimized die-cast aluminium structure with extremely durable semi-matt finish and acoustically optimized metal grilles.
| 100 dB | | 58 Hz - 20 kHz (± 2.5 dB)
55 Hz - 20 kHz (-3 dB) | | 3.0 kHz | | Bass 5" + Treble 3/4“
metal dome + DCWTM | | Bass 40 W + Treble 40 W | | H x W x D 285 x 189 x 178 mm | | 5.5 Kg (12.1 lb) | | 1 x balanced Phoenix connector |
|
Reviews
There are no reviews yet.