Content |
Genelec 7060B Active Subwoofer is powerful and precise bass monitoring tool for modern 6.1 or 5.1 channel Surround Sound or traditional stereo systems.
With its 19 Hz lower cut-off frequency, high sound pressure output capability and versatile bass management systems, it can be adapted to all low frequency monitoring situations.
The amplifier unit integrated into the cabinet contains active crossover filters, driver overload protection circuits and power amplifiers.
The in-built bass management unit has six signal input and output channels, summed signal output connectors and LFE input equipped with a selectable 85/120 Hz lowpass filter and a 0 / +10dB LFE sensitivity switch.
| 108 dB | | Main 19 - 85 Hz (± 3 dB)
LFE 19 - 120 Hz (± 3 dB) | | 0 to -270° (90° steps) | | 10" Active | | 120 W | | H x W x D 527 x 462 x 363 mm | | 26 Kg (57 lb) | | 6.1 XLR analog in
6 x XLR analog out
1 x XLR Link out |
|
Genelec 7070A Active Subwoofer is powerful and precise bass monitoring tool for modern 6.1 or 5.1 channel Surround Sound or traditional stereo systems. With its 19 Hz lower cut-off frequency, high sound pressure output capability and versatile bass management systems, it can be adapted to all low frequency monitoring situations.
The amplifier unit integrated into the cabinet contains active crossover filters, driver overload protection circuits and power amplifiers.
The in-built bass management unit has six signal input and output channels, summed signal output connectors and LFE input equipped with a selectable 85/120 Hz lowpass filter and a 0 / +10dB LFE sensitivity switch.
| 112 dB | | Main 19 - 85 Hz (± 3 dB)
LFE 19 - 120 Hz (± 3 dB) | | 0 to -270° (90° steps) | | 12" Active | | 250 W | | H x W x D 625 x 555 x 490 mm | | 50 Kg (110 lb) | | 6.1 XLR analog in
6 x XLR analog out
1 x XLR Link out |
|
The Sub6 is a large volume cabinet design, equipped with an 11" woofer and a rear laminar port. This configuration guarantees bass linearity whatever the intended SPL. The control board is extremely versatile, with connectivity which allows a 2.1, 2.2 and multichannel use via the L/R inputs and outputs and the LFE. The numerous settings such as the high-pass crossover dedicated to monitors, the adjustable phase and level control provide optimum coupling with the Solo6 Be and the Twin6 Be monitors. And finally, a small, but important point: the footswitch input. It enables one to connect a pedal to deactivate the subwoofer and the high-pass crossovers on the outputs that supply the monitors. This simplifies and greatly improves control during the different stages in monitoring.
Specifications Frequency response : | 30Hz - 250Hz | Maximum SPL : | 116dB SPL (peak @ 1m) |
Input :
|
Right, left, LFE
Electronically balanced, 10 kOhms
XLR 3 points socket
Adjustable
| Outputs (towards speakers) : | Type/Impedance: Electronically balanced / 50 Ohms - Connector: XLR 3 points plug |
Amplification :
|
350W rms, BASH® technology
|
Signal internal treatment :
|
Subwoofer section: Mono right/left summation
LFE + mono low-pass
24dB/octave
Phase adjustment
Polarity selection switch
Switch high-pass filter, cut-off frequency selection
Speaker section : 24 dB / octave
|
Electric supply :
|
Local supply wire: 230V (1.6A fuse)
or 115V (3.5A fuse)
Connection: removable IEC supply wire
|
Visualization and control :
|
Adjustable subwoofer level
Low-pass cut-off frequency setting
Phase adjustment
Polarity adjustment
Subwoofer switch (mute)
2.1 "Bypass" (external remote contol)
High-pass frequency selection
Releasable high-pass
| warning light : | Power on LED, Subwoofer switch (mute), Released high-pass |
Electric supply :
|
Local supply wire: 230V (1.6A fuse)
or 115V (3.5A fuse)
Connection: removable IEC supply wire
| Subwoofer : | 11W7670, 10-5/8" (27cm) Focal "W" composite sandwich cone driver | Box : | 7-1/2" (19mm) MDF panels |
Finish :
|
Dark red natural veneering side panels, black body.
| Dimensions (HxWxD) : | 14-15/16 x 13-9/16 x 17-5/16 " (380 x 344 x 440mm) | Weight : | 50.7lb (23kg) |
|
The Temblor T8 features an 8“, down-firing, glass-composite woofer which is powered by a Class AB amplifier that delivers 200 watts of power. It has a round, front-firing acoustic port, 1/4" TRS and RCA main inputs, and 1/4" TRS and RCA pass-through outputs to connect your top speakers.
The speaker also includes a continuously variable low-pass filter that can be set between 50 Hz to 130 Hz, and also has a switchable high-pass filter that removes content below 80 Hz from the full-range signal sent to your satellite speakers, allowing you to create a seamless crossover transition.
8-inch, downward-firing, glass-composite low-frequency transducer Round, rear-firing, bass-reflex acoustic port Polarity invert assures the sub is phase aligned with top speakers Internal damping and heat sink Integrated rubber feet for stable placement Technical SpecificationsInputs | 2x Balanced 1/4" TRS
2x Unbalanced RCA | Outputs | 2x Balanced ¼" TRS (full range with 80 Hz HPF option) 2x Unbalanced RCA (full range with 80 Hz HPF option) | Frequency Response | 30 Hz - 200 Hz | Low Pass Filter | 50 - 130 Hz (variable) | Signal to Noise Ratio | >98 dB (A weighted) | THD | 0.05% | Amplifier Power | 200 W peak, 100 W RMS | Power Consumption | 120 W | Amplifier Type | Class AB | Max Peak SPL | 104 dB at 1 m | Woofer | 8" glass-composite, downward-firing | Port | Rear-firing bass reflex (round) | Input Gain Adjustment | -30 to +6 dB | Polarity Reverse | 0 or 180° | Low Pass Filter | 50 Hz to 130 Hz | High Pass Filter | On/off | Protection | RF interference
Output-current limiting
Over-temperature
Turn-on/off transient
Subsonic filter
External mains fuse
| Power | 100-120 V ~50/60 Hz or 220-240 V ~50/60 Hz | Cabinet | Vinyl-laminated MDF | Dimensions | 10.2 x 12.6 x 11.0" (260 x 320 280 mm) | Weight |
21.2 lb (9.6 kg)
|
| To hear what's really going on at the bottom of your mixes, you need a subwoofer that speaks the truth. The TemblorTM T10 lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls not normally available in this price range.
Main components - 10-inch glass-composite low-frequency transducer
- Front-firing, bass-reflex acoustic port
Controls and filters - Input gain control (-30 dB to +6 dB, continuously variable)
- Continuously variable lowpass filter (50 Hz to 130 Hz)
- Built-in crossover
- Switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the T10 outputs to the main monitors
- Momentary footswitch (included) bypasses the subwoofer, highpass filter, and Sub Out
- Polarity invert and ground-lift switch
Power and safety - 250 watt, Class AB amplification
- Internal damping and heat sink
- Integrated, gravity-calibrated rubber feet for stable placement
Inputs and outputs - Left and right, balanced XLR and ¼" TRS and unbalanced RCA main inputs
- Left and right balanced XLR and ¼" TRS outputs
- XLR subwoofer output for connecting a second T10
Inputs |
| 2- Balanced XLR |
| 2- Balanced ¼" TRS |
| 2- Unbalanced RCA | | | Outputs |
| 2- Balanced XLR (full range with 80 Hz HPF option) |
| 2- Balanced ¼" TRS (full range with 80 Hz HPF option) |
| 1- Balanced XLR (Sub Out) | Performance | Frequency Response | 20 Hz - 200 Hz | Low Pass Filter Frequency | 50 - 130 Hz (variable) | Signal-to-Noise Ratio | >98 dB | THD | 0.019% @ power | |
Product details
Woofer: | 10-inch black Glass-Composite Cone | Frequency response: | 20Hz - 200Hz | Crossover frequency: | 50Hz - 130Hz adjustable | Amplifier Power: | 300W | S/N Ratio (A weighted): | >95dB | THD + N @ Rated Power: | 0.08% | Inputs: | 2x XLR, 2x TRS, 2x RCA Connectors | Outputs: | 2x XLR, 2x TRS, 1x XLR balanced (Sub out) Connectors | Input Impedance: | 20 kOhm balanced, 10 kOhm unbalanced | Phase reverse: | 0 / 180° switch | Ground Lift switch: | On / Off | Bypass Footswitch: | On / Off | Available colors: | Red, Black | Net weight: | 17.6kg / 38.7lb | Net Dimensions: | L385 x W340 x H390 mm
L15.16 x W13.39 x H15.35 in |
|
Reviews
There are no reviews yet.