| Content |
The FC 3 is a high quality dual capsule condenser microphone, inspired by classical microphone models.
The FC 3 is a very versatile microphone with a wide frequency response and a large dynamic range. It will perform great in the studio or in live sound and broadcast applications.
It´s sound character is similair to vintage microphones and it is well suited to be used with most instruments and voices. Use it on vocals and choirs, acoustic and electric guitars and other fretted instruments, as a drum overhead or room mic and in any other application where you would use a big capsule condenser mic.
The FC 3 is, in spite of it´s low cost, suitable for critical recording applications.
The FC 3 comes with a spider style shock mount. |
- Polar pattern: Cardioid
- Switchable -10dB PAD
- Frequency response: 20 - 20,000 Hz
- Max. SPL: 140/150 dB (THD = 0.5%)
- Electrical impedance: 200 Ohm
- Requires phantom power
- Diameter: 53 mm
- Length: 162 mm
- Net weight: 320 g
- Colour: Black
- Incl. shock mount
- Highly affordable AKG large-diaphragm microphone technology
- Cardioid polar pattern for multiplicity of vocal and instrument applications
The earlier model C 3000 has had a large fan club in the project studio and home recording worlds for years. For the new C 3000 B, AKG designed a special 1-inch large-diaphragm transducer that closely approximates the vibration performance of top-class studio microphones, but can be made at much lower cost.
Due to its surface area and special capsule tuning, the C 3000 B large-diaphragm transducer produces an exceptionally pleasing, smooth sound. Unlike in the C 3000, the switchable 10-dB preattenuation pad immediately follows the transducer in the signal path, thus increasing the C 3000 B\'s SPL capability by a true 10 dB. Loud sound sources are therefore no problem.
An acoustically optimized cardioid polar pattern makes the C 3000 B an excellent choice for both recording and live sound applications where high gain before feedback is paramount.
| Polar pattern |
cardioid |
| Frequency range |
20 to 20,000 Hz |
| Sensitivity |
25 mV/Pa (-32 dBV) |
| Max. SPL |
140/150 dB (k=0,5%) |
| Equivalent noise level (CCIR 468-3) |
25 dB |
| Equivalent noise level |
14 dB-A |
| Signal/noise ratio (A-weighted) |
80 dB |
| Preattenuation pad |
10 dB, switchable |
| Bass filter |
6 dB/octave below 500 Hz |
| Impedance |
200 ohms |
| Recommended load impedance |
>1000 ohms |
| Supply voltage |
9 to 52 V phantom power to DIN 45596 |
| Current consumption |
|
| Connector |
3-pin XLR |
| Finish |
silver gray |
| Net weight |
320 g / 11.3 oz. |
| Shipping weight |
950 g / 2.1 lbs. |
| Patent(s) |
Electrostatic transducer (Patent no. AT 395.225, DE 4.103.784, JP 2.815.488) |
|
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm | Behringer C-3 Dual-Diaphragm Studio Condenser Microphone
Introducing the Professional Condenser Microphone C-3 from BEHRINGER
Our latest dual-diaphragm condenser microphone C-3 is ideal for high-quality studio recording and live applications.
The selectable omnidirectional, cardioid, and figure-eight pickup patterns offer ultimate versatility needed to professionally record vocals and acoustic instruments. The C-3 holds a pressure-gradient transducer with a shock-mounted dual-diaphragm capsule. Its ultra-high sound resolution and flat frequency response rival those of microphones with much higher price tags. It also includes an LED that indicates phantom power operation and a gold-plated XLR output connector to ensure highest signal integrity. The C-3 comes with extensive accessories such as swivel stand and transport case.
The C-3 represents state-of-the-art technology at a price that is simply unheard of. |
NT2000 - ?Explore, Control, Create?? Seamlessly Variable Dual 1? Condenser Microphone.
The world's first large diaphragm condenser studio microphone with seamlessly variable Polar
Patterns, Filter and Pad located conveniently on the microphone body. The NT2000?s state of
the art surface-mount electronics combined with the new Australian designed and manufactured
HF1 Capsule, provide extremely low self-noise (7 dBA) and a maximum SPL of 147 dB (157 dB
with pad fully engaged) ensuring exceptional results and the ultimate in recording creativity.
The NT2000 is supplied with the SM2 Shock Mount, together in a durable custom carry case.
SPECIFICATIONS:
Acoustic principle:
Externally polarised 25 mm (1?) dual diaphragm condenser
Directional pattern: Multipattern
Frequency range: 20Hz - 20KHz
Output impedance: 200 ohms
Signal noise ratio din iec 651: 87 dB (1kHz rel 1Pa)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1K ohm) 157dB (@ 1% THD into 1K ohm) with pad set to maximum
Sensitivity:
-36 db re 1 Volt/Pasca (16 mv @94db SPL) +/- 2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: Phantom P48
Weight without battery: 831 gm
Weight with battery: 2.6 kg
| AKG C214 – large 1” diaphragm microphone with cardioid polar pattern, frequency response: 20Hz-20kHz, 20dB pad, requires phantom power (12-52V), XLR connector. Includes clip, case and windshield. Dimensions: 160 x 55mm. Weight: 280g, optional microphone holder SA61
The C214 professional large-diaphragm condenser microphone has been designed as a cost-effective alternative to the high-end C414 family. Like the C414, the C214 offers a supreme one-inch capsule on an integrated suspension to reduce mechanical noise. A switchable 20dB attenuation pad allows recording of loud sources of up to 156dB SPL. A switchable bass-cut filter allows close-up recording with almost no proximity effect.
The C214 captures sound by combining one capsule of the legendary C414 dual-capsule system and the patented AKG Back-Plate Technology, resulting in an outstanding performance close to the famous C414 XLII.
Sonic character of the C414 XLII
for beautifully detailed recording of lead vocals and solo instruments
Outstanding dynamic range and ultralow noise
for close-up recording of high-output sources of up to 156dB SPL
Switchable 20dB attenuator and bass-cut filter
for close-up recording and reduction of proximity effect
Integrated suspension
to reduce mechanical noise and vibration from stage
Roadworthy design
all-metal die-cast body with shock- and scratch-resistant finish |
Reviews
There are no reviews yet.