Content |
The R 2 MkII is quite different from the R 1 series of mics. It features a ribbon transducer with a shorter and more narrow ribbon. It is darker sounding than the R 1 series since the higher frequencies roll off earlier.
The R 2 MkII will do wonders with both clean and distorted electrical guitar, with brass instruments and more. It is delivered with a metal shock mount.
|
Variable large diaphragm microphone | Pressure-gradient transducer with double membrane capsule | The studio microphone classic | Three directional characteristics: omni, cardioid, figure-8 | Switchable low frequency roll-off | Switchable 10 dB pre-attenuation |
Ideal as main and as support microphone in the most differing recording situations
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Omnidirectional, cardioid, figure-8 plus | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 20/28/22 mV/Pa1) | Rated impedance | 200 ohms | Rated load impedance | 1 kohms | Equivalent noise level, CCIR2) | 26/23/25 dB1) | Equivalent noise level, A-weighted2) | 15/12/14 dB-A1) | Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) | 68/71/69 dB1) | Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) | 79/82/80 dB1) | Maximum SPL for THD 0.5%3) | 117 dB (cardioid) | Maximum SPL for THD 0.5% with preattenuation3) | 127 dB | Maximum output voltage | 390 mV | Dynamic range of the microphone amplifier (A-weighted) | 105 dB | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | Current consumption (P48, IEC 61938) | 0.8 mA | Matching connectors | XLR3F | Weight | 500 g | Diameter | 56 mm | Length | 200 mm |
| |
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm | Behringer C-2 2 Matched Studio Condenser Microphones
2 Matched Studio Condenser Microphones
- 2 matched condenser microphones for stereo studio recording and live applications
- Ideal as main and support microphones for studio and live applications
- Cardioid pickup pattern for effective feedback elimination
- Low-mass diaphragm for ultra-wide frequency response and ultimate sound reproduction
- Switchable low-frequency roll-off and input attenuation
- Ultra low-noise transformerless FET input eliminates low-frequency distortion
Excellent Source Isolation
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Sound That Astounds
Every stitch of these mics is designed to deliver beautiful sound. Beginning with the gold-plated 3-pin XLR connector, you get the highest signal integrity.
Once connected to your system, youʼll notice these twin pro-caliber microphones have a 4 dB boost in the 1 kHz - 8 kHz range. For those of you new to condenser mics, this basically means youʼll get a slightly brighter sound that will give the perfect shape to cymbals and overhead miking. Acoustic pianos and choirs also benefit greatly from this type of frequency response.
Excellent Source Isolation
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
You Are Covered
We always strive to provide the best possible Customer Experience. Our products are made in our own MUSIC Group factory using state-of-the-art automation, enhanced production workflows and quality assurance labs with the most sophisticated test equipment available in the world.
As a result, we have one of the lowest product failure rates in the industry, and we confidently back it up with a generous 3-Year Warranty program. | The C 414 B/XLS has been carefully designed to maintain the legendary sonic character of the C 414 family while integrating new features and performance enhancements made possible by new technology. The C 414B/XLS is designed to deliver accurate pickup of all acoustic instruments and voices.
The microphone's 5 pickup patterns are easily selectable via an electronic switch with LED indication and offer the selection of omnidirectional, cardioid, wide cardioid, hypercardioid and figure-eight patterns.
The pickup pattern selector switch utilizes a dual-color LED indicator that provides visual indication of the pattern selected and also changes from green to red to indicate if the microphone's output electronics are being overloaded. The pattern selector can also be used to "lock" the microphone's switch settings by pressing and holding it for 3 seconds.
On the rear of the microphone, an electronic switch allows the selection of -6 dB, -12 dB and -18 dB pre-attenuation levels which are accomplished by changing the polarization voltage to the capsule. The C 414 B/XLS has switchable bass cut filters of 12 dB-per-octave at 40 Hz and 80 Hz, and a 6-dB-per-octave filter at 160 Hz for control of proximity effect. On-axis sensitivity for all patterns is 23 mV/Pa and its self-noise is an extremely low 6 dB-A.
The C 414 B/XLS has a transformerless output and all-metal chassis, making it immune to electrical interference and RF from digital equipment, video monitors and wireless systems. It comes complete in an all-metal road case with the AKG H-85 shock mount, a PF80 external two-stage pop filter, a W414X external windscreen and an individually-measured chart showing the response curve of the microphone. It is also available in factory-matched stereo pairs packaged with a H50 stereo bar instead of the external pop filter.
The C 414B/XLS is built in Vienna, Austria and comes with a three-year limited parts and labor warranty.
Features
High sensitivity and extremely low self noise
Five switchable polar patterns for placement and application flexibility
Two-color LEDs provide quick visual indication of selected polar pattern and output overload
Elastic capsule suspension greatly minimizes structurally-transmitted noise from chassis vibration
H 85 professional shock mount/stand adapter, PF 80 external pop filter and W 414 X external windscreen
High sound pressure level capability and wide dynamic range
Completely immune to electrostatic and electro-magnetic interference from digital gear, computer monitors, etc. thanks to solid metal housing and transformerless output stage
Three switchable bass cut filters and three pre-attenuation pads with LEDs for quick visual indication
All switchable components operate in low impedance circuits for ultra-high relability even in extremely humid conditions
Optional R 414 remote control unit (available by the end of 2004) offers full control of all switchable parameters via standard microphone cable and 3-pin XLR-type connectors
Specifications
Type: 1" large diaphragm pressure gradient microphone
Polar Patterns: Omnidirectional, wide cardioid, cardioid, hypercardioid, figure eight
Frequency Range: 20 to 20,000 Hz
Sensitivity: 23 mV/Pa (-33 dBV) +/-0.5 dB
Max. SPL: 140/146/152/158 dB SPL (at 0/-6/-12/-18 dB)
Preattenuation Pad: -6, -12,-18 dB, switchable
Bass Cut Filter Scope: 12 dB/octave at 40 Hz and 80 Hz; 6 dB/octave at 160 Hz
Power Requirements: 48 V phantom power to DIN/IEC
Connector: 3-pin XLR
Dimensions: 2" x 1.5" x 6.3“
Net Weight: 10.6 oz
Shipping Weight: 5 lbs (2.27 kg) | AKG C214 – large 1” diaphragm microphone with cardioid polar pattern, frequency response: 20Hz-20kHz, 20dB pad, requires phantom power (12-52V), XLR connector. Includes clip, case and windshield. Dimensions: 160 x 55mm. Weight: 280g, optional microphone holder SA61
The C214 professional large-diaphragm condenser microphone has been designed as a cost-effective alternative to the high-end C414 family. Like the C414, the C214 offers a supreme one-inch capsule on an integrated suspension to reduce mechanical noise. A switchable 20dB attenuation pad allows recording of loud sources of up to 156dB SPL. A switchable bass-cut filter allows close-up recording with almost no proximity effect.
The C214 captures sound by combining one capsule of the legendary C414 dual-capsule system and the patented AKG Back-Plate Technology, resulting in an outstanding performance close to the famous C414 XLII.
Sonic character of the C414 XLII
for beautifully detailed recording of lead vocals and solo instruments
Outstanding dynamic range and ultralow noise
for close-up recording of high-output sources of up to 156dB SPL
Switchable 20dB attenuator and bass-cut filter
for close-up recording and reduction of proximity effect
Integrated suspension
to reduce mechanical noise and vibration from stage
Roadworthy design
all-metal die-cast body with shock- and scratch-resistant finish |
Reviews
There are no reviews yet.