Content |
HeadAMP - Four Output Stereo Headphone Amp Overview
Most home recordings involve from one to four people, any or all of whom are
going to need headphone monitoring. The monitor amp would be connected
to the tape deck?s headphone output or a mixer output so that the performers
can hear themselves and each other. Of course the same application can apply
to band rehearsals and even home entertainment. HeadAMP provides amplification
and individual volume control for up to 4 headsets. It can be driven by either line-
level or headphone amplifier signals (mono or stereo).
HeadAMP - Four Output Stereo Headphone Amp Specifications:
Signal To Noise Ratio >90dB
IMD (SMPTE) 0.01%
Maximum Input Level +14dBV
Maximum Output Level 20dB per channel
Output Impedance 51 Ohms per channel
Output Connectors Four stereo 1/4? headphone outputs
Power Requirements 12V DC (Adapter included)
Total Harmonic Distortion |
Specifications
General
Frequency response
20 Hz - 20 kHz (+0 dB, -1.5 dB)
Signal-to-noise ratio
100 dB (IHF A-weighted, input level control min.)
Channel separation
80 dB between adjacent channels
Line input
Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced
Input impedance
40 kOhm
Nominal level
-10 dBV (0.3 V)
Headphone outputs
four 6.3 mm stereo jacks
Maximum output power
2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)
Power supply
230 V AC, 50 Hz
Power consumption
10 W
Dimensions (W x H x D)
482 mm x 44 mm x 196 mm
Weight
4 kg |
INPUT: 1 audio stereo, 1Vpp/50kΩ on a 6.5mm stereo phone socket.
OUTPUTS: 5 audio stereo, 500mW/8Ω on 6.5mm stereo phone sockets.
AUDIO BANDWIDTH (-3dB): 25kHz.
CONTROL: 5 stereo output level controls (front), 1 mono switch (rear).
GAIN RANGE: -60dB to +10dB.
S/N RATIO: 78dB.
THD: 0.08% @100mW.
POWER SOURCE: 12V DC, 370mA nom, 1A max.
DIMENSIONS: 16.5cm x 12cm x 4.5cm (6.5” x 4.72” x 1.77”) W, D, H.
WEIGHT: 0.68kg (1.5lbs) approx.
ACCESSORIES: 12V DC power supply.
OPTIONS: RK-1 19" rack adapter.
|
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
| The new HP4 from PreSonus answers the need for a headphone distribution
amplifier with professional specifications in a small package at an affordable
price. The HP4 features four discrete headphone outputs on the front panel
each with its own volume potentiometer and 150mW of amplification per channel.
The HP4 also features adjustment over control room monitors with a separate
volume control, monitor mute switch and mono switch giving you an extremely
powerful monitoring solution at an amazingly low price.
Features
? Four High Power Headphone Outputs
? Ultra loud (150mW per channel)
? Ultra quiet operation
? Musical Wide Dynamic Range
? Control Room Monitor Outputs with Level Control
? Mono or Stereo Operation
? Monitor Mute Switch
? Daisy Chain an Infinite Number of Units
? Compact package
Technical Specifications
Input
TRS Impedance 10K Ohms
Panel Controls
Headphone Level 1 to 12
Monitor / Feed Output -80dB to +10dB
Mono Switch
Monitor / Feed Mute
Power Supply
Type Linear
Input 16VAC/1000mA
Output
TRS Balanced 51 Ohms Impedance
Performance
THD+Noise (Unweighted) 0.002%
Noise Floor -98dB
Signal To Noise >95dB
Power Supply Rejection >98dB
Power 16 Watts
Physical
Weight 5lbs./ 2.3 kg.
Dimensions 5.5 x 5.5 x 1.75
Mounting Max Rack and Universal Rack Tray
Chassis Steel
Panel Brushed Aluminum
Sides Cast Aluminum | Behringer HA-400 Ultra-Compact 4-Channel Stereo Headphone Amplifier
Mini to the max! You can use this super-compact stereo headphone amplifier with practically all headphones?four of them at the same time, to be exact! For example, you can let up to 4 different people in your studio listen to the main mix while the recording is being made, and each listener can determine his own volume level using the dedicated output level controls. The HA400 contains 4 high-power stereo amplifiers that maintain the highest sonic quality even at maximum volume levels. Ultra low-noise 4580 operational amplifiers are included for outstanding audio performance?these are the same op amps found in ?full-size? audio equipment?plus, a DC 12-Volt adapter is included.
If you are one of those musicians who like to deck out their equipment with lots of bells and whistles, the HA400 definitely makes a great addition to the functionality of your studio.
The Behringer HA400 offers flexible amplification for up to 4 headphones. Whether you're tracking a full band, playing to a backing track, or just listening to your mix, this compact amp gives every performer diverse volume control.
Hear everything with clarity. The HA400 promises high audio quality with zero interference, no matter what headphones you use. Behringer are relied upon by professional musicians everywhere. With the HA400 headphone amplifier, you'll become a part of 50+ years of innovation and expertise.
The Highest Quality Monitoring Possible
Great monitoring is at the heart of a tight performance. Whether you're on stage or in the studio, the HA4000 delivers ultimate control for everyone playing. Discover the highest quality audio from 4 high power, stereo amplifiers. Even at maximum volume, this tidy headphone amp provides clear sound without muddiness or unwanted noise.
Industry Leading Standard
There's a reason why Behringer are leaders in their field. With 50+ years of industry experience, they've built a legacy around exceptional build quality and innovative design. The HA4000 is no exception. Every channel preserves the original sonic qualities of your input signal. That's performance you can trust.
Features
- Ultra-compact headphone amplifier
- Ideal for stage or studio use
- Full control for every channel with 4 independent stereo high-power amplifier sections
- Extremely high audio quality with virtually all types of headphones, even at maximum volume
- 12V DC power adapter included
- Designed and engineered by Behringer in Germany
Specifications
Line Inputs
-
-
- Type: 1/4'' TS Jack, Stereo
- Impedance: 100kohms
- Max. input level: +15dBu
Headphone Outputs
-
-
- Type: 1/4'' TRS Jacks, Stereo
- Impedance: Approx. 80ohms
- Max. output level: Approx. 40mW in 100ohms
Power Supply
-
-
- Power supply: External power supply 12V
Dimensions/Weight
-
- Dimensions: 47mm (H) x 57mm (W) x 104mm (D)
- Weight: 0.32kg
|
Reviews
There are no reviews yet.