D&R HYBRID-1 mk2 Telephone Hybrid Passive Broadcasting

310.00 incl. GR VAT

In stock (can be backordered)

EAN: 7436917139152
Installments calculation
CompareAdd to wishlist Submit Better Price
D&R’s newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way. Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a […]

 

Read more

D&R’s newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way.

Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs.

Telephone hybrids provide the interface between professional audio equipment and the public telephone network.

They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line.

Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source.

A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines.

Specification

Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to  more than 30dB.

C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation.

R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation.

TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection.

ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line

Weight 0.50 kg

Reviews

There are no reviews yet.

Be the first to review “D&R HYBRID-1 mk2 Telephone Hybrid Passive Broadcasting”

Your email address will not be published. Required fields are marked *

Quick Comparison

D&R HYBRID-1 mk2 Telephone Hybrid Passive Broadcasting removeARX QUADCOMP 4CHANNEL COMPRESSOR-LIMITER removeBEHRINGER FBQ100 DIGITAL FEEDBACK SUPPRESOR removeShure DP11EQE with Gate, Expander removeBEHRINGER MDX2600 COMPOSER PRO XL PROCESSOR removeALPHATON FC-100 FEEDBACK CONTROLLER remove
NameD&R HYBRID-1 mk2 Telephone Hybrid Passive Broadcasting removeARX QUADCOMP 4CHANNEL COMPRESSOR-LIMITER removeBEHRINGER FBQ100 DIGITAL FEEDBACK SUPPRESOR removeShure DP11EQE with Gate, Expander removeBEHRINGER MDX2600 COMPOSER PRO XL PROCESSOR removeALPHATON FC-100 FEEDBACK CONTROLLER remove
Image
SKUHYBRID-1 mk2QUADCOMPE005280DP11EQEE005313FC-100
Rating
Price 310.00 incl. GR VAT 446.39 incl. GR VAT 95.00 incl. GR VAT 422.00 incl. GR VAT 174.00 incl. GR VAT 166.65 incl. GR VAT
Stock

In stock (can be backordered)

Only 1 left in stock (can be backordered)

In stock

In stock

Available on backorder

In stock

AvailabilityIn stock (can be backordered)Only 1 left in stock (can be backordered)In stockIn stockAvailable on backorderIn stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentD&R's newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way. Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs. Telephone hybrids provide the interface between professional audio equipment and the public telephone network. They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line. Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source. A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines. Specification Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to  more than 30dB. C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation. R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation. TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection. ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line

Features
Four Independent Compressor Channels
Channels 1 and 2, 3 and 4 are stereo linkable
7 LED Gain Reduction metering
Balanced XLR Inputs and Outputs
Sidechain Insert points
Intuitive, user friendly layout
Flawless performance
 
The sheer amount of effects and signal processors necessary for today's standards
of audio production puts a great strain on the available space in equipment racks,
both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp.
An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four
channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our
original design concept. The Quadcomp  is still four variable ratio Compressor/ Limiters
neatly housed in a compact all steel 1 RU package. However, all new low noise/low
distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp
in a class of its own.
More Control, Less Space
On the front panel, each channel has the 'industry standard' individual controls for Threshold,
Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual
indication of the amount of gain reduction being applied to the program, and an IN/OUT
hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write
on for easy confirmation of compressor assigns.
Precision Circuitry
Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters
for low distortion and accuracy, plus program dependent attack and release time, which
automatically determines optimum compressor response.
Balanced Inputs and Outputs
The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor.
Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive
compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260).
Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate
stereo tracking. When switched IN, the first channel becomes the master and controls all the functions
of the second except Output gain.
Universal AC Power
AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via
a standard IEC connector, with built-in fuse and voltage switch.
Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs,
Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry
and clean uncluttered layout make it a truly useful audio tool for all applications.

T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 20dB
CMRR >50dB, 20 Hz?20 KHz
Output Impedance
Balanced 300 ohms Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz-20KHz ±0.5dB
Signal to Noise ratio
-93 dB Unweighted, -98 dB ?A? weighted
Distortion .015% THD @ 0dB,1KHz
Dynamic Range 108 dB
Attack and Release Times Program dependent
Metering
7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB
Sidechain Insert Impedance 10 Kohm
Power Requirements
100/120 V AC or 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input Connector type Balanced XLR
Output Connector type Balanced XLR
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
7 LED Gain Reduction display
Marker panel for labelling compressor assigns
Stereo link status LEDs
Rear Panel Connectors
Input and Output balanced XLR connectors
TipRingSleeve Sidechain insert connectors
Channels 1 and 2, 3 and 4 Stereo link switches
IEC AC mains connector with inbuilt fuse and
voltage change

SHARK FBQ100 Automatic Feedback Destroyer with Integrated Microphone Preamp, Delay Line, Noise Gate and Compressor High performance single channel Feedback Destroyer with integrated microphone preamp, delay line, noise gate and compressor Automatically and "intelligently" locates and destroys up to 8 feedback frequencies Narrow FBQ filters for extremely effective feedback suppression, while keeping highest sonic quality Ultra-low noise Mic/Line input with Gain control and +48 V phantom power Delay line with up to 2.5 seconds of delay, adjustable in meters, feet and msec Noise gate with automatic and manual parameter settings Automatic compressor with variable density Subsonic filter with adjustable cut-off frequency Balanced inputs and servo-balanced outputs with ¼'' TRS and gold-plated XLR connectors High-quality components and exceptionally rugged construction ensure long life Conceived and designed by BEHRINGER Germany

Shure DP11EQE Dynamics Processor Specification:

    GENERAL:
        Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
        Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
        Sampling Rate: 48 kHz
        Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
    Voltage Gain:
        1 dB +/- 1dB (power off)
        12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
        12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
        0 dB +/- 2 dB (equal input and output sensitivities)
    Impedance:
        Input: 47 kilohms +/- 20% actual
        Output: 120 ohms +/- 20% actual
    Input Clipping Level
        +18 dBu minimum (at +4 dBu setting)
        +6 dBV minimum (at 10 dBV setting)
    Output Clipping Level
        +18 dBu minimum (at +4 dBu setting)
        +6 dBV minimum (at 10 dBV setting)
    Total Harmonic Distortion
            LED Signal Indicators
        Signal: 40 dB
        Clip: 6 dB down from input clipping
    Propagation Delay from Input to Ouput
        0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
    Polarity
        Input to output: inverting optional (default: non-inverting)
        XLR: pin 2 positive with respect to pin 3
        1/4-inch TRS: tip positive with respect to ring
    Operating Voltage
        DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
        DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
        DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
    Temperature Range
        Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
    Fuse
        DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
        DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
        DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
    Dimensions
        219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
        Weight: 930 g (2.05 lbs)
    DYNAMICS PROCESSOR
        Gate and Expander:
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 1.0 to 200 ms
        Decay: 0.05 to 1 second
        Gate Hold Time: 0 to 0.5 seconds
    AGC Leveler
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 0.2 to 3 seconds
        Decay: 0.5 to 5 seconds
        Hinge: Threshold to 1 dB, 0.5 dB resolution
    Compressor and Limiter
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 1.0 to 200 ms
        Decay: 0.05 to 1 second
        Knee: Hard or Soft selectable
    No Overshoot Peak Limiter
        Propagation delay: 1 ms
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 0 msDecay: 100 ms
    PARAMETRIC EQUALIZER
        Parametric Filter Frequency Bands
        Up to 9 bands, variable frequency, variable Q
    Boost/Cut Range
        +6 dB to 18 dB per band
        Q Range
        1/40-octave to 2 octave
    High and Low Shelf/Cut Filters
        Shelf, +6 to 18 dB per filter
        Cut, 12 dB per octave nominal
    DELAY
        Up to 1.3 seconds, 21 microsecond resolution

Interactive Reference-Class 2-Channel Expander/Gate/Compressor/ Peak Limiter with
Integrated De-Esser, Dynamic Enhancer, Tube Simulation and Low Contour Filter 

Whether you?re recording, mixing or mastering, the COMPOSER PRO-XL MDX2600
gives you total dynamic control. It includes all of the features you would expect from
a reference class compressor?plus a voice-adaptive de-esser, a new dynamic
enhancer, authentic tube emulation and much more. These are some of the indispensable
tools for producing clean, consistent audio with virtually no loss in signal quality.

Features:
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression circuitry
combines the advantages of hard-knee and soft-knee characteristics
Integrated de-esser with switchable male/female voice recognition removes excessive
sibilance from your vocal tracks
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible
noise suppression
Switchable tube simulation for the extra warmth and transparency of classic
tube circuitry
Automatically or manually adjustable attack and release times
Switchable low contour filter prevents "pumping" due to low-frequency
dominated compression
Stereo couple function with independent output level settings
Switchable side chain input with side chain monitor function
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 12-segment LED meters for input/output levels and gain reduction
Dedicated "traffic light" threshold and de-esser level displays
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Relay-controlled hard bypass switch with auto bypass function in case
of power failure
Manufactured under ISO9000 certified management system
 

Description

The alphaton Feedback-Controller FC-100 is a revolutionary product for every microphone
application including wireless types. It can provide effective feedback control to any sound
reinforcement situation. It can also eliminated string feedback in guitars and bass instruments
which are equipped with piezo or condenser pickups.
The FC-100 provides 6 to 10 dB of feedback protection by analysing the incoming signal,
detecting the presence of feedback and then notching out the feedback frequency.
The FC-100 relieves the sound engineer automatically. It works dynamically and eliminates a
feedback signal before it can grow into a peak. Internally a discriminator circuit detects the
presence of regenerative feedback and triggers the automatic equaliser to insert a notch where
the feedback peak is coming up. This normally prevents other peaks from developing but if they
do, the process is repeated at high speed, thus keeping feedback under control.

Technical Data
In- and Outputs transformer balanced
max. Inputlevel + 3 dB
Gain (RS=200 Ohm, RL=2kOhm) 0 dB
Frequency Response 20 Hz ... 20 kHz, +/- 1,5 dB
Feeback Cancellation  6 ... 10 dB
Power Requirement  30 ... 48 V Phantom
Current drain ca. 8 mA
External Power Supply 9 ... 20 V DC, 3,5 mm jack, tip +
Housing Aluminium Diecast
Weight  285 grams
Dimensions  112 x 60 x 32 mm

Weight0.50 kg5.20 kg0.38 kg3.00 kg3.30 kg0.30 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0.50 kg
Weight 5.20 kg
Weight 0.38 kg
Weight 3.00 kg
Weight 3.30 kg
Weight 0.30 kg