Content |
Power Output Level: QD4240
8ohm (Quad Ch) 40W
4ohm (Quad Ch) 60W
8ohm bridged mono 120W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ | POWER AMPLIFIER 4 X 2100 WATT / 4Ω
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start |
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
|
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuit. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 4 Ohms)
4 x 810 W
Rated ouput power (1kHz @ 8 Ohms)
4 x 490 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
2 x 1600 W
Frequency response
20 - 20000 Hz
Total Harmonic Distortion (THD)
< 0.1 %
Signal-to-noise ratio
105 dB
Input sensitivity
0.775 V
Protection circuits
DC protection , short circuit , thermal overload
Controls
4 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
|
Reviews
There are no reviews yet.