INTERM QD-4480 AMPLIFIER 4X120W

Power Output Level:  QD4480                       

8ohm (Quad Ch)       80W    
4ohm (Quad Ch)       120W    
8ohm bridged mono   240W 

Input Sensitivity (8ohm, 1kHz)  0.775Vrms
Input Impedance 20kohm Balanced 
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz 
T.H.D. (f=20Hz~20kHz, Half Power) 0.03% 
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz)  100
Rasidual Noise  -85dB
Channel Separation (8ohm, 1kHz)  80dB
Voltage Gain (4ohm)  26dB 29dB 32dB
Power Source  100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption  300W 420W 770W
Weight  11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions  482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
 

The C 16:4 is one of two mid-power, four-channel amplifiers in the C Series family. Attractively packaged in a 2U chassis, it provides 4 × 400 W output into 4 ohm loads.

C Series amplifiers are uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL™), which allows the output to be optimized for any loudspeaker load – whether a single large subwoofer or a series of small 100/70 V loudspeakers. VPL works in combination with adjustable input gain to achieve maximum headroom regardless of input levels or output impedances.

Every C Series is ready for the NomadLink® network right out of the box. With NomadLink, key amplifier parameters are displayed via DeviceControl software, and remote control of channel mutes and power on/off is under network control.

Specifications C 16:4

General
Number of channels 4
Peak total output all channels driven 1600 W
Peak output voltage per channel 141 V
Max. output current per channel 8.5 Arms
Max. Output Power 16 ohms 8 ohms 4 ohms 2 ohms Hi-Z
Per ch. (all ch.’s driven) 400 W 400 W 300 W n.r. 400 W (70 Vrms / 100 V peak)
Bridged per ch. 800 W 600 W n.r. n.r. 800 W (140 Vrms / 200 V peak)
Performance with Gain: 35 dB and VPL: 100 V
THD 20 Hz - 20 kHz for 1 W 70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB 6.8 Hz - 34.2 kHz
Input impedance 20 kOhm
Input Common Mode Rejection, CMR 50 dB
Output impedance @ 100 Hz 30 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 3) 141, 118, 100, 85, 71, 59, 50, 42 V
VPL, selectable when bridged 3) 1) 282, 236, 200, 170, 142, 118, 100, 84 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1)
– rear-panel switches
23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain 35 dB
Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB, hidden behind security panel/dust filter grille
Connectors and switches
Input connectors (per ch.) 3-pin Phoenix, electronically balanced
Output connectors (per ch.) Barrier strip 2-pole screw terminals
Output bridge mode A+B and/or C+D, inputs A and C are input source
NomadLink® network On board, 2 x RJ45 connectors
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off Individual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators
Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on
Per channel
Signal present / High-impedance; -10 dB and -4 dB output signal; Voltage Peak Limiter (VPL); Current Peak Limiter (CPL);
Very High Frequency (VHF); High Temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 130 -265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush current draw Yes / max. 5 A
Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20P
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”)
Weight 12 kg (26.4 lbs.)
Finish Black painted steel chassis with gray painted steel front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
Note 1): Automatic -6 dB gain compensation when bridging channels. Ch.’s A+B and/or C+D, can be bridged individually.
Note 2): PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker.
Refer to Operation Manual.
Note 3): For sine waves, peak voltage output values translate to Vrms with the formula V/1.41 = Vrms. E.g. 100 V peak equals app. 70 Vrms.
Hence, outputs can be set for high-impedance loads without requiring a transformer.
All specifications are subject to change without notice.

• 4 x 75 Watts into 4 Ohms; 4 x 50 Watts into 8 Ohms
• ATR (Accelerated Transient Response) technology for ultimate punch and clarity
• Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption
• Independent limiters for each channel offer maximum output level with reliable overload protection
• Detented gain controls for precise setting and matching of sensitivity
• Precise Power, Signal and Clip LEDs to monitor performance
• Servo-balanced XLR and 1/4" TRS inputs plus professional speaker connectors
• Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
• “Back-to-front" ventilation system including air filter for reliable operation
• “Built-like-a-tank“, impact-resistant and all-steel 1U rackmount chassis
• Minimum depth chassis (10.1" / 257 mm) and ultra-light weight design (8.8 lbs / 4.0 kg) fits into compact, inexpensive effects racks
• High-quality components and exceptionally rugged construction ensure long life

• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis

Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz

Phase Response (@1W 20Hz-20kHz): ±15deg

Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB

Voltage Gain (selectable): 26/32/38 dB

Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V

Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB

Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A

Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches

Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs

Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™

Electro Voice PA 4150L features:

    * 100 Watts / 8 Ohms
    * 160 Watts / 4 Ohms
    * The amplifier channels can be bridged for more flexibility
    * Frequency response (-1dB): 10 Hz - 40 kHz
    * Signal-to-Noise Ratio: 100 dB
    * Provides excellent headroom for a wide dynamic range on music signals
    * Protection: audio limiters, high temperature, peak current limiters, turn-on delay
    * Marked level controls on the rear panel provide hidden reliable level adjustments for each channel
    * Front panel LEDs indicate signal present, 0 dB, and limit
    * Phoenix type connectors for inputs and outputs provide an easy rack wiring
    * Cooling: front-to-rear
    * Power requirements: 120V or 230V, 50 Hz - 60 Hz
    * Dimensions (WxHxD): 483 x 88 x 406 mm / 19" x 3.5" x 16"
    * Weight: 18 kg / 39.65 lbs

The DPA series amplifiers are digital power amplifiers designed to meet the specialized needs of sound contractors for Multi-Zone distributed speaker systems. They are designed in six different models of Class D power amplifiers, divided in three different architectures to meet the requirements for all kinds of applications.

They combine the best of all features in one single series of amplifiers, providing an outstanding sound quality with all the known advantages of Class D Amplifiers. Such as the excellent efficiency and very low heat dissipation. And due to the complete passively cooled entity only a minimal of maintenance is needed, while ensuring maximum reliability.

The small size of a single rack space make them very interesting for fixed rack mount as well as mobile applications.

The DPA74 is built as multi channel power amplifier with four individual controllable channels containing various specific features and advanced protection circuitry which protects against DC malfunctioning, short circuit, overheating and overload.

The signal input connections are accommodated with balanced XLR connectors. The operation mode can be selected between Stereo mode, Bridge mode and Parallel mode. The output connections are accommodated with Euro-Terminal blocks.

• Model Name / Type: DPA74 / Digital Amplifier
• 8 ohms: 4 x 50 W
• 4 ohms: 4 x 75 W
• 8 ohms Bridge: 2 x 150 W
• THD+N:
• Signal / Noise: > 100 dB
• Frequency Response: 20 Hz - 20kHz
• Power Supply: 240 V AC / 50 - 60 Hz
• Dimensions (W x H x D): 483 x 44 x 300 mm