Content |
Info
The PA-6336 is Inter-M's best-selling commercial PA amplifiers. The 6300 Series are recognized for their ruggedness, reliability and performance. They are the installerʼs choice for sound reinforcement, background music, paging, and public address systems. Featuring low-distortion, low-noise amplifier electronics circuits which provides a high-output and a high S / N ratio. PA 6300 series amps provide a wide dynamic range with excellent headroom. An onboard High Pass Filter protects both amplifier and speakers from damaging transients. A comprehensive thermal/electrical protection circuit ensures long-haul dependability. Thermister protected output helps ensure overall stability and provides input overload protection. Internal airflow and exceptionally quiet multi-stage fans ensures amplifier cooling. Phoenix-style terminals provides for quick, easy hookup. Models are available in a variety of output power, 120, 240, 360 and 480 watts power output in 8/4 ohm low impedance and in 70/100V high impedances output using low-distortion transformers. The PA 6300 series offers outstanding versatility, long term reliability, and a remarkable value for any installation application.
|
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier. |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) | - Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
Specification |
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | Power Consumption | 2.2A or less at rated power output. | Output Power | Rated 15W, max. 35W | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | Distortion | Less than 5% (at 1kHz rated output) | Frequency Response | 100 ~ 10,000Hz | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | Dimensions | (W x H x D): 178 x 50 x 132mm (mounting device excluded) | Weight | 900g | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (4A) ... 1
Connection cord ... 1 set | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
Reviews
There are no reviews yet.