INTER-M PA-360 MIXER-AMP 6 INPUT 360W 4Ω/100V 5 ZONE

Overview

The Inter-M PA Series is an mixing amplifier. They are complete and economical multi-purpose

desktop mixing amplifiers providing a cost-effective solution to public address and other similar

applications.

It is a successor model of PA-2000A / 4000A / 6000A which are the best-selling models of

Inter-M. While retaining most of the features of the existing system, it is designed to make higher

amplifier output and more compact design than conventional systems by using the technology of

Class-D amplifier.

Six versions are available with outputs of 60, 120, 240, 360, 480 and 600 watts respectively

into Low-Impedance(4 Ω) or High-Voltage(70 V/100 V line) speaker systems. Especially

from PA-240 to PA-600 has designed a High-Voltage output without the output transformer(OPT)

by using the Inter-M digital amplifier technology.

The PA Series amplifier is designed for reliable service for voice reproduction and BGM applications.

It is an ideal solution for medical offices, restaurants, schools, etc.

- 2U Size

- 360W output power

- SMPS delivers high power output with low power consumption and weight reduction

- 5 Microphone/Line Inputs, EXT IN and TELL IN with individual volume control

- Input Level LED Monitor per channel

- Separate BASS/TREBLE Tone Controls

- 5 zone selection switches

- Independent built-in Attenuator over Zone 5.(Maximum 50W, more than 200Ω)

- PRIORITY

- Remote MUTE and CHIME terminal

- VCA Remote volume controll

Power Output Level:  QD4480                       

8ohm (Quad Ch)       80W    
4ohm (Quad Ch)       120W    
8ohm bridged mono   240W 

Input Sensitivity (8ohm, 1kHz)  0.775Vrms
Input Impedance 20kohm Balanced 
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz 
T.H.D. (f=20Hz~20kHz, Half Power) 0.03% 
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz)  100
Rasidual Noise  -85dB
Channel Separation (8ohm, 1kHz)  80dB
Voltage Gain (4ohm)  26dB 29dB 32dB
Power Source  100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption  300W 420W 770W
Weight  11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions  482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
 

mplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V)
Analog Inputs 4, electronically balanced, Phoenix-type
Audio Network No
CAN Bus Interface Yes (With Optional RCM-810 Card)
Continuous Rated Power
(1 kHz, THD 1%) 100v 500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 70v 500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 250 Watts
Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans
DIM 30 0.02 %
Electronics Type Amplifier
Frequency Response 15 Hz-30 kHz
Input Impedance (Balanced) 20 kΩ
Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V
Intermodulation Distortion (SMPTE) 0.05 %
Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz
Maximum Bridged Output 4Ω 1000 Watts
Maximum Bridged Output 8Ω 1000 Watts
Network Control (IRIS-Net) Optional
Slew Rate 28 V/µs
Total Harmonic Distortion 0.05 %
Variable Load Drive (VLD) Yes
Height 2RU 88.1 mm (3.47“)
Width 481 mm (18.94“)
Depth 421.5 mm (16.59“)
Weight Net 11.1 kg (24.47 lbs)

    * Weight: 18 kg / 39.65 lbs

• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis

Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz

Phase Response (@1W 20Hz-20kHz): ±15deg

Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB

Voltage Gain (selectable): 26/32/38 dB

Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V

Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB

Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A

Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches

Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs

Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™