INTER-M A-500 30W MODULAR DIGITAL AMPLIFIER

Model    CT475
Product Type    Amplifier
Channels    4
Sensitivity    1.4V
Rated Power Output    75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted    110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)    Intermodular Distortion (from 0dB down to -40dB)    Frequency Response (at 1W into 4/8 ohms)    ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz)    > 70dB
Common Mode Rejection (20Hz to 1kHz)    > 55dB, typically > 70dB
Dimension (H x W x D)    1.75" x 19" x 14.25“
Weight    10 lbs (4.5 kg)

  

Model    CT475
Product Type    Amplifier
Channels    4
Sensitivity    1.4V
Rated Power Output    75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted    110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)    Intermodular Distortion (from 0dB down to -40dB)    Frequency Response (at 1W into 4/8 ohms)    ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz)    > 70dB
Common Mode Rejection (20Hz to 1kHz)    > 55dB, typically > 70dB
Dimension (H x W x D)    1.75" x 19" x 14.25“
Weight    10 lbs (4.5 kg)

• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis

Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz

Phase Response (@1W 20Hz-20kHz): ±15deg

Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB

Voltage Gain (selectable): 26/32/38 dB

Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V

Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB

Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A

Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches

Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs

Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™

High-tech in professional amplification!

The fP 2400Q is a lightweight and space-saving four-channel power amplifier, ideal for
use in high quality touring sound systems as well as in demanding permanent installations.
The fP 2400Q offers a diverse choice of applications, such as: multi-channel monitor
systems, four-channel reproduction, and compact amplification in active 2-, 3-, and 4-way
systems.
The fP 2400Q makes possibile the bridge connection of one or two of the two pairs of
channels (channel A and B and/or channel C and D). It also features Lab.gruppen?s unique
power matching solution, the MLS switch, which offers endless combinations for solving
most of the problems related to varying impedances and maximum power capacities of
loudspeakers. The latest semiconductor technology is utilized in the new ferrite Power (fP)
amplifiers.
This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances
the 2 ohms capacity. Two easily accessible dust filters on the front ensure a clean front-to-rear
airflow. Additionally, a new Bi-phase wiring scheme also increases the capacity of the switch
mode power supply. This extends the power bandwidth in the low end.

Key Features:
4 x 370 watts @ 8 ?
4 x 380 watts @ 4 ?
4 x 500 watts @ 2 ?
(Measured just below clip level, with all 4 channels driven)
Light weight and compact: only 8.6 kg (19lbs), 2U high
MLS? Switch: Lab.gruppen?s unique power matching for different loads

New Features:
Replaces the LAB 1200C
Easily accessible dust filters
Improved low-end power bandwidth
Extruded front panel for increased stability

Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features
to make the fP family functional in all situations from installation to high performance live
sound systems:

Regulated switch mode power supply
Today there are many lightweight, switch-mode amplifiers in the market. However, the unique
Lab.gruppen switch-mode power supply technology offers a number of essential advantages
that make it superior to other and seemingly similar power supply designs. The most important
features are the regulated power supply and the extreme power efficiency. The regulated power
supply easily deals with a very high variation in the AC mains voltage: it can drop by up to 20%
below its nominal level - e.g. to 180 V instead of 230 V ? without any problem. Perhaps even
greater benefits result from the extreme efficiency of Lab.gruppen amplifiers: only a fraction of the
energy from the AC mains is turned into heat.
A regulated power supply also presents some other sonic advantages, such as better cone control
and the same fast response as a conventional power supply.

Sophisticated protection circuitry, combining:
ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but
keeps the amplifier within the Safe Operation Area
DC protection; protects against infrasonic signals
VHF protection; protects the loudspeakers against strong very high frequency non-musical signals
above the audible range
Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front
panel are switched on, as a warning, before the protection process is initiated
AC protection; shuts down the power supply if the line voltage is outside the operating voltage
Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining
full peak power.

Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4
Sensitivity, RL=8. Att.max +4dB
S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB
Idle Power Consumption 40W
1/8 Power Consumption (4Ω) 500W
Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, 0dB
Residual Noise, 20Hz-20kHz(DIN AUDIO) -70dB
Voltage Gain, 8Ω, f=1kHz 100
Sensitivity, ATT. max 26dB
Maximum Input Voltage 22dB
Input Impedance 30kΩ (balance) 15kΩ (unbalance)
Controls, Front panel POWER switch (push on/push off), attenuator (31position) x 4
Controls, Rear panel MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (OFF/20Hz/55Hz 12dB/oct) x 2
Connectors, Output 5–way binding post/ch
Connectors, DATA PORT D-sub15P, Monitor:Output Level/ch,Active/ch, Model Detect Control:Mute/ch
Connectors, Power AC inlet x 1
Indicators, POWER x 1 (Green)
Indicators, SIGNAL x 4(Green)
Indicators, CLIP/LIMIT x 4 (Red)
Indicators, PROTECT/MUTE x 4 (Red)
Load Protection POWER switch on/off mute, DC-fault output relay off
Power Requirements UC: 120V / 60Hz,
Weight 10kg (22 lbs.)
Dimensions (W x H x D) 480 x 88 x 412.2 mm (18-7/8" x 3-7/16" x 16-1/4“)