Content |
- Unidirectional Dynamic Microphone
- Remote Chime Switch
- Mic ON/OFF Switch
- 2 Push Buttons for Easy Operation
| |
|
RM-01
| Input Sensitivity / Impedance |
75dB±3dB (0dB=1V/µber at 1,000Hz), 600ohm
| Frequency Response |
100Hz~18kHz
| Type |
Moving Coil Dynamic
| Directional Characteristic |
Unidirectional
| Weight |
3lbs.
1.4kg
| Dimensions |
3.5(W) X 1.8(H) X 5.2(D) inches
90(W) x 45(H) x 133(D) mm
|
*Specifications and design subject to change without notice for improvements.
| |
| Optimized for low-frequency bass punch/high-power SPL handling. Designed for kick drum.
The Shure BETA®52A is a high output dynamic microphone with a tailored frequency response designed specifically for kick drums and other bass instruments. It provides superb attack and "punch“, and delivers studio quality sound even at extremely high sound pressure levels.
The Beta 52A features a modified supercardioid pattern throughout its frequency range to insure high gain-before-feedback and excellent rejection of unwanted sound. A built in dynamic locking stand adapter with an integral XLR connector simplifies installation, particularly if the microphone is to be placed inside a kick drum. The stand adapter keeps the microphone position fixed and resists slipping, even when subjected to sharp blows and strong vibrations. A hardened steel mesh grille protects the Beta 52A from the abuse and wear associated with touring.
Features
- Frequency response shaped specifically for kick drums and bass instruments
- Built–in dynamic locking stand adapter with integral XLR connector simplifies setup, especially inside a kick drum
- Studio quality performance, even at extremely high sound pressure levels
- Supercardioid pattern for high gain before feedback and superior rejection of unwanted noise
- Hardened steel mesh grille that resists wear and abuse
- Advanced pneumatic shock mount system that minimizes transmission of mechanical noise and vibration
- Neodymium magnet for high signal–to–noise ratio output
- Low sensitivity to varying load impedance
- Legendary Shure quality and reliability
Type |
Dynamic (moving coil) |
Frequency Response |
20 to 10,000 Hz |
Polar Pattern |
Supercardioid, rotationally symmetrical about microphone axis |
Output Level |
Open Circuit Voltage: -64 dBV/Pa* (0.6 mV), *1 Pa = 94 dB SPL |
| The Shure KSM141 is an end-addressed condenser microphone with mechanically switching dual polar patterns (cardioid and omnidirectional). Designed for studio use, yet rugged enough for live applications, the KSM141 can withstand extremely high sound pressure levels (SPL). Its low self-noise and extended frequency response make it ideal for recording musical instruments.
Features
- A mechanical polar pattern switch for highly consistent cardioid and true omnidirectional polar patterns. Provides flexibility in a wide variety of recording applications
- Ultra-thin, 2.5 micron, 24 karat gold-layered, low mass Mylar? diaphragm for superior transient response
- Class A, discrete, transformerless preamplifier for transparency, extremely fast transient response, no crossover distortion, and minimal harmonic and intermodulation distortion
- Premium electronic components, including gold-plated internal and external connectors
- Subsonic filter eliminates low frequency rumble (less than 17 Hz) caused by mechanical vibration
- Three-position switchable pad (0 dB, 15 dB, and 25 dB) for handling extremely high sound pressure levels (SPLs)
- Three-position switchable pad (0 dB, 15 dB, and 25 dB) for handling extremely high sound pressure levels (SPLs)
- Three-position switchable low-frequency filter to reduce background noise and counteract proximity effect
Performance Characteristics
- Extended frequency response
- Low self noise
- Exceptional reproduction of low-frequency sounds
- Can withstand high sound pressure levels (SPL)
- High output level
- No crossover distortion
- Uniform polar response
- Superior common mode rejection and suppression of radio frequency interference
APPLICATIONS
Some typical applications for the KSM141 are listed below. Microphone use, however, is a matter of personal taste. The KSM141 may be used for a variety of applications other than those listed.
- Acoustic instruments -- such as piano, guitar, drums, percussion, strings
- Wind instruments -- brass and woodwind
- Low frequency instruments -- such as double bass, electric bass, kick drum
- Overhead miking -- drums or percussion
- Ensembles -- choral or orchestral
- Room ambiance pick-up -- guitar amplifier or drums
Both the acoustic environment and microphone placement strongly affect the sound obtained from miking a source. You may need to experiment with microphone placement and room treatments to achieve the best overall sound for each application.
Suggested Applications
Acoustic Guitar
Acoustic Bass
Cymbals
Brass/Woodwinds
Orchestra
Ensemble Vocals
Piano
Strings
Room Ambience
Live Recording | MASTER AUDIO – CM238
Pen-type microphone
- Directivity: condenser – ultra cardioid
- Frequency response.: 100Hz – 16Khz
- Sensitivity: -44db +/- 2db for short distance – -23db +/- 2db for long distance
- Output impedance: 1K Ohm for short distance – 2.3K Ohm for long distance
- Power supply: 1.5V / phanthom 48V
- Dimensions: Ø 23 x 360 mm.
- Windscreen, microphone holder and cable (4,5 m.) included
|
Designed to operate exclusively with the PAM-340A the RM-05A will allow either individual selection of any combination of paging zones or the all-all facility. A flexible gooseneck microphone is supplied together with a three metre lead, complete with multiway connectors to connect the RM-05A to the host amplifier. Power: Supplied by the host PAM-340A. Dimensions: 195mm(w) x 60mm(h) x 205mm(d). Weight: 1.2 kg including microphone. | The Shure SM58S Vocal Microphone features a cardioid dynamic vocal design well suited for professional vocal use in live performances, sound reinforcement, and studio recording. A built-in spherical filter minimizes wind and breath "pop" noise, while the cardioid pickup pattern isolates the main sound source while minimizing unwanted background noise. The microphone offers durable construction, a high-quality internal shockmount system, and a steel mesh grille for withstanding rough handling. The SM58S is designed to perform consistently both outdoors and indoors and when used for singing or speech applications. The microphone features an integrated on/off switch and includes a microphone clip and a zippered pouch.
- Pneumatic shockmount system cuts down handling noise
- Effective, built-in spherical wind and pop filter
- Supplied with break-resistant microphone clip that rotates 180 degrees
- High quality, rugged, and reliable
- Cardioid dynamic
- Frequency response: 50 Hz to 15 kHz
Suggested Applications
Lead Vocals
Backup Vocals
Harmonica
Frequency Range |
50 Hz to 15 kHz |
Impedance |
150 Ohms |
Sensitivity |
-57.5 dBV/Pa at 1 kHz |
|
Reviews
There are no reviews yet.