| Content |
This versatile amplifier is one of two mixer amplifiers, giving outputs of 60W (JPA 1060) and 120W (JPA 1120), each with five balanced inputs and 100/70 volt line or low impedance output. 240 volt ac or 24 volt dc powered.
The amplifier is designed to accommodate any of the tuner, cassette, CD or message store modules in the associated range (JTP 10, JCP 10, JCR 10, JCDR 10A, JCDP 10A and JDM 10A)
| Technical Specification |
|---|
| Model: | JPA 1120 | | Order Code: | 10-0402-C07 | | Power Output (RMS): | 120W | | Loudspeaker Outputs: | 100V, 70V / 4ohm, 8ohm | | AC Power: | 50Hz 240V 50Hz | | DC Power: | 24V | | THD at rated power: | 60dB | | Signal/Noise ratio, Aux: | >70dB | | Treble Control: | ±10dB at 10kHz | | Bass Control: | ±10dB at 100Hz | | Dimensions: | H110 x W420 x D320 mm | | Weight: | 12kg |
|
XV Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile,
dynamic and extremely rugged according to IEC286-3. For the
highest requirements in safety and quality.
Sequential power on, alive contacts and incorporated ground fault
detection - the XV is the solution under all conditions. Without the
need for additional equipment. For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers
in the XV series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 1600: 2x 800 W / 100 V
Class: AB
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans(temp. reg. variable speed)
Weight: 39 kg
Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
- Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 4.4A or less at rated power output. | | Output Power | Rated 30W, max. 60W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency | Response 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 144mm (mounting device excluded) | | Weight | 1.1 kg | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (8A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
| | - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-120A/340A/480Aʼs audio capabilities. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - SPEAKER SELECT Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for Channels 1 and 2, Chime and Telephone input over other input sources. - REMOTE CONTROL INPUT (only PAM-340A/480A) Individual speaker zones can be selected and chime can be operated by wired remote control. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - EM(EMERGENCY) - OPTIONAL EMERGENCY VOICE IC (only PAM-340A/480A) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. | | | | | | | | | Rated Output Power | PAM-120A(THD 1%) : 120W (RMS) PAM-340A(THD 3%) : 340W (RMS) PAM-480A(THD 3%) : 480W (RMS) | | Frequency Response | | Amp In | 80Hz~20kHz | | Link In | 80Hz~15kHz | | CH1~CH6 | 120Hz~8kHz | | Remote In | 120Hz~8kHz(PAM-340A, PAM-480A) | | T.H.D.(at 1kHz Rated Output) | Less than 1%(PAM-120A) | | T.H.D.(at 1kHz Half Power Output) | Less than 0.5%(PAM-340A, PAM-480A) | | S/N | | Amp In | Better than 90dB(PAM-120A) Better than 88dB(PAM-340A/480A) | | Link In | Better than 65dB | | CH1~CH6 | Better than 50dB | | Remote In | Better than 50dB(PAM-340A/480A) | | Input Sensitivity/Impedance | | CH1~CH6 | | TRIM VR -60dB Position | 1mV/10kΩ | | TRIM VR -16dB Position | 158mV/10kΩ | | Link In | 100mV/10kΩ | | Amp In | 1V/47kΩ(PAM-120A) 1V/20kΩ(PAM-340A/480A) | | Remote In | 1V/10KΩ(PAM-340A/480A) | | Speaker Output/Impedance | PAM-120A : 120W/4Ω, 70V/42Ω, 100V/83Ω PAM-340A : 340W, 100V/29.4Ω PAM-480A : 480W, 100V/20.8Ω | | Preamp Output/Impedance | 1V/600Ω | | Tone Control (100Hz, 10kHz) | ±12dB | | CH1~CH6 EQ Control (100Hz, 1kHz, 10kHz) | ±12dB | | | | | | | | Power Source | 100–120VAC or 220V–240VAC; 50/60Hz, 24V DC(only PAM-120A) | | | (Supplied AC mains transformer depends on country requirements) | | Power Consumption | PAM-120A : 135W(1/8 POWER), 200W(1/3 POWER), 300W(FULL POWER) PAM-340A : 260W(1/8 POWER), 400W(1/3 POWER), 620W(FULL POWER) PAM-480A : 360W(1/8 POWER), 550W(1/3 POWER), 880W(FULL POWER) | | Weight | PAM-120A : 13kg/28.7lb PAM-340A : 13.5kg/29.7lb PAM-480A : 15.5kg/34.2lb | | Dimensions | 420(W) x 132(H) x 360(D)mm/16.5(W) x 5.2(H) x 14.2(D)in | | Operation Temperature | 14F~104F (-10°C~+40°C) | | ※ Specifications and design subject to change without notice. | | | |
|
- HIGH POWER, LOW DISTORTION
120W of RMS power with less than 1% THD.
- ADVANCED PROTECTION CIRCUITRY
Thermal and current overload protection, power-on delay and automatic idling circuitry for component and loudspeaker protection.
- BATTERY BACKUP
Can be powered by 24VDC battery for emergency backup and true portability.
- SLIM DESIGN, COMPACT SIZE
Streamlined design fits in a compact 3RU space.
|
PA- 2312
|
|
Rated Output (RMS, THD 1%, 1kHz)
|
120W
|
|
Input Sensitivity/Impedance
|
1V/10kΩ, Balanced
|
|
T.H.D
|
Less than 1%
|
|
S/N
|
Better than 95dB
|
|
High Pass Filter
|
-3dB at 400Hz
|
|
Channel Separation
|
Less than –70dB
|
|
Output Voltage/Impedance
|
EC, JAPAN: 4Ω/22V, 41Ω/70V, 83Ω/100V
|
USA/CANADA: 4Ω/22V, 5.2Ω/25V, 41Ω/70V
|
|
Power Source
|
100–120VAC or 220–240VAC; 50/60Hz, 24VDC
|
|
Power Consumption(1/8 Power)
|
290W
|
|
Weight
|
20Kg/44.1Ib
|
|
Dimensions
|
482(W) x 132(H) x 280(D)mm/19(W) x 5.2(H) x 11(H)in
|
|
Reviews
There are no reviews yet.