| Content | ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift.
| Brand |
KLARK TEKNIK |
| Model |
DN100 |
| DI Type |
Active |
| Channels |
Mono |
| Application |
Concert, Portable PA, Studio |
| Warranty |
3 Years |
The new Klark Teknik DN100 Direct Injection Box is the
natural successor to the long-established LBB100.
A ground-up redesign provides an extended dynamic range,
lower noise floor and all the world-class audio performance
you?d expect from Klark Teknik. DN100 is also designed to
handle the rigours of life on the road: a thick aluminium shell
protects the electronics, and this in turn is protected by a
tough silicone rubber casing, which is replaceable and available
as a spare part.
We?ve also fitted a Kensington security slot in one of the end
panels to allow the unit to be made secure using a Kensington
MicroSaver security cable.
Attention to detail ? it?s what makes a good unit into a great one.
DN100 Technical Data:
Input:
Type active electronic, balanced or unbalanced
Impedance 1M ohms nominal, balanced or unbalanced (jack connectors)
20K ohms (XLR input only)
Connectors 2 quarter inch jacks and 3-pin XLR linked in parallel
Max. Level 30dBu
Attenuator 30dB, switchable
Output:
Type Transformer Isolated, balanced
Impedance 300 ohms
Connector 3 pin XLR
Max. Level 10dBu with load >2k ohms
Min. load 600 ohms
Performance:
Noise -100dBu, 20Hz to 20kHz unweighted, with input terminated by 10k resistor
Frequency response +0.5/-1dB 20Hz to 20kHz
Distortion (THD+N) |
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
| Little brother of the LH-055 DI Box. Sturdy housing, solid workmanship at an unbeatable price.
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal (e.g. to a guitar amplifier) 1 low-impedance output (XLR) Black housing
Passive 1-channel DI box, black
- 1 high-impedance signal input, 6.3 mm jack
- 1 low-impedance XLR output
- 6.35 mm jack input, and output
- Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
- Switchable input attenuation: 0 dB, -20 dB, -40 dB
- Rugged black metal housing
Package contents
- 1 x device, 1 x user manual
| Frequency range: |
15 - 30000 Hz |
| S/N ratio: |
>95 dB |
| Impedance: |
Input: 50 kOhm
Output: 600 Ohm |
| Input attenuation: |
0 dB, -20 dB, -40 dB; switchable |
| Control elements: |
Groundlift selector |
| Connections: |
Input: 1 x 6.3 mm plug (unbal.)
Link: 1 x 6.3 mm plug (unbal.)
Output: line via 1 x 3-pin XLR |
| Dimensions: |
Width: 12,7 cm
Depth: 7,4 cm
Height: 4,5 cm |
| Weight: |
440 g |
| Behringer DI-400P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI400P lets you connect instruments or amplifier outputs. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage. | Product Features:
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Switchable input attenuation allows input levels of up to +50 dB
Ground Lift switch eliminates typical ground loop problems
¼" TRS and gold-plated XLR connectors
Ultra-rugged, road-suitable aluminum case
Stackable oversized rubber corners
High-quality components and exceptionally rugged construction ensure long life and durability
Conceived and designed by BEHRINGER Germany
With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners. |
2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing |
Reviews
There are no reviews yet.