KLARK TEKNIK DN100 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift

No longer available!

120.00 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
Availability: No longer available! No longer available! SKU: E003228 Category:
ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift. Brand KLARK TEKNIK Model DN100 DI Type Active Channels Mono Application Concert, Portable PA, Studio Warranty 3 Years The new Klark Teknik DN100 Direct Injection Box is the natural successor to the long-established LBB100. A ground-up redesign provides an […]

 

Read more

ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift.
Brand KLARK TEKNIK
Model DN100
DI Type Active
Channels Mono
Application Concert, Portable PA, Studio
Warranty 3 Years

The new Klark Teknik DN100 Direct Injection Box is the
natural successor to the long-established LBB100.
A ground-up redesign provides an extended dynamic range,
lower noise floor and all the world-class audio performance
you?d expect from Klark Teknik. DN100 is also designed to
handle the rigours of life on the road: a thick aluminium shell
protects the electronics, and this in turn is protected by a
tough silicone rubber casing, which is replaceable and available
as a spare part.
We?ve also fitted a Kensington security slot in one of the end
panels to allow the unit to be made secure using a Kensington
MicroSaver security cable.
Attention to detail ? it?s what makes a good unit into a great one.

DN100 Technical Data:
Input:
Type active electronic, balanced or unbalanced
Impedance 1M ohms nominal, balanced or unbalanced (jack connectors)
20K ohms (XLR input only)
Connectors 2 quarter inch jacks and 3-pin XLR linked in parallel
Max. Level 30dBu
Attenuator 30dB, switchable
Output:
Type Transformer Isolated, balanced
Impedance 300 ohms
Connector 3 pin XLR
Max. Level 10dBu with load >2k ohms
Min. load 600 ohms
Performance:
Noise -100dBu, 20Hz to 20kHz unweighted, with input terminated by 10k resistor
Frequency response +0.5/-1dB 20Hz to 20kHz
Distortion (THD+N)

Weight 1.00 kg

Reviews

There are no reviews yet.

Be the first to review “KLARK TEKNIK DN100 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift”

Your email address will not be published. Required fields are marked *

Quick Comparison

KLARK TEKNIK DN100 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift removeDBX DB-10 PASSIVE DI-BOX WITH GROUND LIFT removeOMNITRONIC LH-055 PASSIVE DI BOX removeBEHRINGER DI-600P High-Performance Passive Direct Injection Box removePALMER AUDIO PAN01 Passive DI-box removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) remove
NameKLARK TEKNIK DN100 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift removeDBX DB-10 PASSIVE DI-BOX WITH GROUND LIFT removeOMNITRONIC LH-055 PASSIVE DI BOX removeBEHRINGER DI-600P High-Performance Passive Direct Injection Box removePALMER AUDIO PAN01 Passive DI-box removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) remove
Image
SKUE003228DBX DB-10LH055E005866PAN01AR-133
Rating
Price 120.00 incl. GR VAT 112.00 incl. GR VAT 43.00 incl. GR VAT 39.00 incl. GR VAT 52.07 incl. GR VAT 159.00 incl. GR VAT
Stock

Out of stock

Available on backorder

In stock

In stock

Only 5 left in stock (can be backordered)

Only 5 left in stock (can be backordered)

AvailabilityOut of stockAvailable on backorderIn stockIn stockOnly 5 left in stock (can be backordered)Only 5 left in stock (can be backordered)
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, 30 dB Groundlift.
Brand KLARK TEKNIK
Model DN100
DI Type Active
Channels Mono
Application Concert, Portable PA, Studio
Warranty 3 Years
The new Klark Teknik DN100 Direct Injection Box is the natural successor to the long-established LBB100. A ground-up redesign provides an extended dynamic range, lower noise floor and all the world-class audio performance you?d expect from Klark Teknik. DN100 is also designed to handle the rigours of life on the road: a thick aluminium shell protects the electronics, and this in turn is protected by a tough silicone rubber casing, which is replaceable and available as a spare part. We?ve also fitted a Kensington security slot in one of the end panels to allow the unit to be made secure using a Kensington MicroSaver security cable. Attention to detail ? it?s what makes a good unit into a great one. DN100 Technical Data: Input: Type active electronic, balanced or unbalanced Impedance 1M ohms nominal, balanced or unbalanced (jack connectors) 20K ohms (XLR input only) Connectors 2 quarter inch jacks and 3-pin XLR linked in parallel Max. Level 30dBu Attenuator 30dB, switchable Output: Type Transformer Isolated, balanced Impedance 300 ohms Connector 3 pin XLR Max. Level 10dBu with load >2k ohms Min. load 600 ohms Performance: Noise -100dBu, 20Hz to 20kHz unweighted, with input terminated by 10k resistor Frequency response +0.5/-1dB 20Hz to 20kHz Distortion (THD+N)

At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.

Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.

As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB10 dB12 is for you.

Features
  • Parallel 1/4" Thru Jack
  • Transformer Isolated
  • Premium Shielded Custom dbx Transformer
  • Balanced XLR Lo-Z Output
  • 3-Way 0/20/40 dB Pad Switch
  • Flat/High-Cut Filter Switch
  • Output Polarity Invert Switch
  • Ground Lift Switch
  • 4 Year Warranty!

  • dB10 Specifications INPUT SECTION

    Input: 1 instrument/line/speaker level

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Impedance: 150k Ohm typical

    Max Input Level: +20dBu (0dB pad)
    +40dBu (20dB pad)
    +60dBu (40dB pad)

    OUTPUT SECTION

    Thru Output: 1 parallel connection from input jack

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Main Output: 1 line level

    Connector: XLR male jack

    Type: Balanced

    Impedance: 150 Ohm typical

    Max Output Level: 0dBu

    PERFORMANCE

    Transformer: Custom dbx mu-metal-shielded

    Frequency Response: 20Hz to 20kHz, +/-2.5dB

    Noise:

    THD:

    GENERAL

    Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)

    Weight: 1.4 lbs / 0.65 kg

    Note: Specifications subject to change without notice.

     1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing

    Behringer DI-600P High-Performance Passive Direct Injection Box Introducing the Ultra-Compact DI-Boxes from BEHRINGER There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal. The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies. This is the sort of medicine that?ll cure headaches in your studio or on stage. It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal. Hook Your Guitar or Amp Up to the PA Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig! Behringer Ultra-DI DI600P Direct Box Features:
    • Compact, high-performance passive direct box
    • Jack input 1/4" TS in and parallel out
    • Gold-plated XLR output / impedance balanced
    • Super-flat frequency output for uncolored sound
    • Switchable filter that optimizes the DI for guitars
    • Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
    • Instruments or amplifier outputs with up to 3,000 watts can be connected directly
    • Offers impedance and signal matching of instruments to mixers
    • Perfect for stage and studio use
    • Ground lift switch eliminates typical ground loop problems
    • Rugged metal case can take the rigors of the road
    Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box! Tech Specs
    • Type: Passive DI Box
    • Channels: 1
    • Ground Lift: Yes
    • Inputs: 1 x 1/4"
    • Outputs: 1 x 1/4“, 1 x XLR
    • Height: 1.4"
    • Width: 3.75"
    • Depth: 5"
    • Weight: 0.66 lbs.
    • Manufacturer Part Number: DI600P

    Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.

    Product type DI Boxes
    Type passive
    Channels 1
    Inputs 1
    Input connectors 6.3 mm Jack
    Max. input level + 54 dBu
    Input impedance (@ 60 Hz) 60k Ohm(s)
    Input pad 0 / -30 dB
    Outputs 1
    THRU outputs/channel 1
    Output connectors 6.3 mm Jack , XLR
    Max. output level + 4 dBu
    Output impedance 600 Ohm(s)
    Frequency response 20 - 20000 Hz
    Transformer balanced yes
    Ratio 10 : 1
    Controls attenuator , ground lift
    Cabinet material sheet steel
    Cabinet surface powder coated
    Width 110 mm
    Depth 73 mm
    Height 42 mm
    Weight 0,34 kg

     

    With added functionality and enhanced audio performance, the AR-133 has been designed to be more affordable for musicians, studios and PA companies. The unit includes phantom power and battery supplies as standard. Should the phantom power from the console fail or be accidentally switched off, the AR-133 automatically switches over to the internal 9V battery providing uninterrupted use. The unit is housed in a rugged aluminium extrusion case, with robust polyurethane end-cheeks which give the AR-133 a very distinctive look. Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning that the AR-133 can be used to convert unbalanced signals to a balanced output on XLRs throughout. The arched case allows cables to run back underneath the unit from the end for neat cable management. Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick solutions to ground-loop problems. The AR-133 uses an enhanced version of the same audio path as the AR-116, now regarded by many people as a reference standard. The sound quality is legendary, particularly on acoustic and bass guitars. Numerous applications can be satisfied by the AR-133. For example, as well as the traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier outputs, and other electronic sources.An additional bonus is the ability to use the AR-133 as an active balancing device. Input Section Input Impedance  1M Ohm (pad at 0dB) 47k Ohm (pad at -20dB) 47k Ohm (pad at -40dB) Max Input Level +9dBu (pad at 0dB) +29dBu (pad at -20dB) +49dBu (pad at -40dB) Connectors  Two Parallel 1/4" jack connectors and a parallel XLR connector (unbalanced) Jack:  Tip Hot (+ve) Sleeve Ground XLR: Pin 2 Hot (+ve) Pin 1 & 3 Ground Output Section Output Transformer Balanced Max. Output Level  +8dBu into 600 Ohms or greater Connector  XLR3-32 or equivalent System Performance Distortion (THD)  < 0.005% at 1khz, 0dbu output Noise  < -105db unweighted, 22hz-22khz, rms* Frequency Response 30Hz to 20kHz, +0dB/-1dB General Main/Standby battery 9 volt PP3 type, preferably alkaline. Current drain  on phantom - less than 7.5mA on battery - less than 2mA. Phantom Power  +20 volts DC to +48 volts DC Weight 650 gms, excluding batteries. Overall Dimensions  59 mm x 124 mm x 143 mm (2.3" x 4.9" x 5.6“)
    Weight1.00 kg0.65 kg0.70 kg0.30 kg0.34 kg0.65 kg
    DimensionsN/AN/AN/AN/AN/AN/A
    Additional information
    Weight 1.00 kg
    Weight 0.65 kg
    Weight 0.70 kg
    Weight 0.30 kg
    Weight 0.34 kg
    Weight 0.65 kg