KLARK TEKNIK DN200 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, -5, 30 dB Groundlift

Discontinued

162.00 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of […]

 

Read more

The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch.

In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation.

Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design

Weight 1.00 kg

Reviews

There are no reviews yet.

Be the first to review “KLARK TEKNIK DN200 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, -5, 30 dB Groundlift”

Your email address will not be published. Required fields are marked *

Quick Comparison

KLARK TEKNIK DN200 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, -5, 30 dB Groundlift removeOMNITRONIC LH-065 ACTIVE D.I BOX removePALMER AUDIO PAN01 Passive DI-box removeALPHATON SM-60 ACTIVE D.I BOX removeDBX DB-12 ACTIVE DI BOX WITH GROUND LIFT removeOMNITRONIC LH-055 PASSIVE DI BOX remove
NameKLARK TEKNIK DN200 ACTIVE DI-BOX, plug in/out, XLR in/out, changeable chassis, only use with phantom power, -5, 30 dB Groundlift removeOMNITRONIC LH-065 ACTIVE D.I BOX removePALMER AUDIO PAN01 Passive DI-box removeALPHATON SM-60 ACTIVE D.I BOX removeDBX DB-12 ACTIVE DI BOX WITH GROUND LIFT removeOMNITRONIC LH-055 PASSIVE DI BOX remove
Image
SKUE006290LH065PAN01SM-60DBX DB-12LH055
Rating
Price 162.00 incl. GR VAT 77.67 incl. GR VAT 52.07 incl. GR VAT 113.09 incl. GR VAT 140.00 incl. GR VAT 43.00 incl. GR VAT
Stock

Out of stock

In stock

Only 5 left in stock (can be backordered)

In stock

Available on backorder

In stock

AvailabilityOut of stockIn stockOnly 5 left in stock (can be backordered)In stockAvailable on backorderIn stock
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentThe DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch. In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation. Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design

Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.

Product type DI Boxes
Type passive
Channels 1
Inputs 1
Input connectors 6.3 mm Jack
Max. input level + 54 dBu
Input impedance (@ 60 Hz) 60k Ohm(s)
Input pad 0 / -30 dB
Outputs 1
THRU outputs/channel 1
Output connectors 6.3 mm Jack , XLR
Max. output level + 4 dBu
Output impedance 600 Ohm(s)
Frequency response 20 - 20000 Hz
Transformer balanced yes
Ratio 10 : 1
Controls attenuator , ground lift
Cabinet material sheet steel
Cabinet surface powder coated
Width 110 mm
Depth 73 mm
Height 42 mm
Weight 0,34 kg

 

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.

Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.

As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB12 is for you.

Features
  • Parallel 1/4" Thru Jack
  • Transformer Isolated
  • Premium Shielded Custom dbx Transformer
  • Balanced XLR Lo-Z Output
  • 3-Way 0/20/40 dB Pad Switch
  • Flat/High-Cut Filter Switch
  • Output Polarity Invert Switch
  • Ground Lift Switch
  • 4 Year Warranty!
  • Additional dB12 Features
    • Phantom Powered
    • Green LED Phantom Power Indicator
    • +48V Phantom Operation
    • Low-Noise Active Circuitr

    dB12 Specifications INPUT SECTION

    Input: 1 instrument/line/speaker level

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Impedance: 150k Ohm typical

    Max Input Level: +20dBu (0dB pad)
    +40dBu (20dB pad)
    +60dBu (40dB pad)

    OUTPUT SECTION

    Thru Output: 1 parallel connection from input jack

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Main Output: 1 line level

    Connector: XLR male jack

    Type: Balanced

    Impedance: 150 Ohm typical

    Max Output Level: 0dBu

    PERFORMANCE

    Transformer: Custom dbx mu-metal-shielded

    Frequency Response: 20Hz to 20kHz, +/-2.5dB

    Noise:

    THD:

    GENERAL

    Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)

    Weight: 1.4 lbs / 0.65 kg

    Note: Specifications subject to change without notice.

     1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing

    Weight1.00 kg0.80 kg0.34 kg0.24 kg1.00 kg0.70 kg
    DimensionsN/AN/AN/AN/AN/AN/A
    Additional information
    Weight 1.00 kg
    Weight 0.80 kg
    Weight 0.34 kg
    Weight 0.24 kg
    Weight 1.00 kg
    Weight 0.70 kg