Content | The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch.
In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation.
Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design |
Tube-buffered DI-Box DI-1000
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box. Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur - but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz - 20 kHz (-0,1 dB) 5 Hz - 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A - military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak |
You're serious about getting rid of all that excess noise on stage, but you've got so many line instruments you don't know where to start. The ADB-4 from Stewart can take care of all your high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a lot of DI power.
? Requires phantom power or 9v battery ? Ground lift switch ? Instrument or speaker level switch ? Transformerless ? Can be used with amp up to 400w ? RF shielding |
Palmer PAN 03 19" DI Box 4-Channel active
Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.
Product type
DI Boxes
Type
active
Channels
4
Inputs
4
Input connectors
6.3 mm jack
Max. input level
+ 45 dBu
Input impedance
(@ 60 Hz) 1 M Ohm(s)
Input pad
0 / -30 dB
Outputs
4 (+ 4 parallel XLR outs)
THRU outputs/channel
1
Output connectors
6.3 mm jack , XLR
Max. output level
+ 10 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 20000 Hz
Transformer balanced
Yes
Ratio
10 : 1
Indicators
Power
Controls
attenuator , ground lift
Operating voltage
external
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
480 mm
Width
19 "
Depth
90 mm
Height
45 mm
Height
1 U
Weight
1,6 kg
|
Inline Transformer IA-2
The model IA-2 line matching transformers !S designed to properly match a low impedance signal to a low impedance source. The advantage of "ground lift" switching allows to optmize hum problems. Technical Data Frequency response 20 Hz - 20 KHz + 1 dB Impedance 600 : 600 Ohm THD K3 50 Hz = 0.5 % Level < + 6 dBm Weight 100 g Dimensions diameter 17 mm, lenght 115 mm |
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
Reviews
There are no reviews yet.