Content | The DN200 Active Stereo Direct Injection Box from Klark Teknik is a dual-channel and multi-mode stereo DI box that delivers superior connectivity and audio performance. Housed in a robust alloy case with the same form factor as the DN100 Single-Channel DI, and further protected by a replaceable silicon sleeve, the DN200 features inputs on pairs of XLR, TRS, and RCA sockets, plus a switchable 20 dB pad and a ground lift switch.
In addition, the DN200 can operate in Sum mode, where left and right input signals are merged and routed to both left and right outputs, or Split mode, routing the left input signal to both the left and right outputs. The DN200 supports 24 to 48V phantom-power operation.
Dual-channel active direct injection boxRugged Neutrik Combo XLR connectors featuring high-impedance DI jack inputsRCA Phono inputsIndependent phantom power for each channel for maximum reliabilitySum switch optionally routes both inputs to both outputsSplit switch optionally routes left input to both outputsGlobal 20 dB Input Pad and Earth Lift switches24 to 48V phantom-powerStackable, protective silicone rubber sleeveCompact and rugged design |
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm |
Phantom or battery powered in a rugged steel chassis, with separate Speaker Level input connector The ARX DI-PLUS represents another major step forward in active direct boxes. Packaged in a single channel stand-alone format, the DI-PLUS represents a fresh look at active D.I. concepts. Precision engineered Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade components, plus an all-steel chassis gives excellent hum and noise specifications and superb audio quality in a tough, roadworthy package. Level control The DI-PLUS features a Normal gain high impedance unbalanced input on the front panel, running to a balanced XLR output on the rear. There is also a separate -40dB Speaker Level input for signal coming from the External (auxiliary) speaker output of an amplifier. A a global Pad switch drops both the normal input and the speaker input by a further 20dB, making it suitable for all applications, from the softest keyboard to the hottest broadcast levels. Battery compartment The revolutionary simple 'clamshell' action of the DI-PLUS battery compartment makes battery changing extremely easy, even on the darkest stages. A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip leads to break, no tools required, no screws to lose. Production crew heaven! Automatic Phantom switching The DI-PLUS will automatically switch itself to the console's own Phantom Power, if available, and an LED will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode. Rugged all-steel case A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer chassis of the DI-PLUS provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that is hard to dislodge, and hard to leave behind. Rear panel showing XLR connector, ground lift switch, and captive screw for opening up the unit for battery changing Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all the dynamics and clarity of the original sound source transferred to the mixing console. The ARX DI-PLUS provides a rugged, no-compromise solution to all direct injection and signal balancing requirements. T E C H N I C A L S P E C I F I C A T I O N S: Max Input Level +13 dB Phantom powered +6 dB Battery powered Input Impedance 1 Meg Ohm Max Output Level +17 dB 10K Ohm load Phantom powered +12 dB 10K Ohm load Battery powered +11 dB 600 Ohm load Phantom powered +12 dB 600 Ohm load Battery powered Output Impedance 680 Ohms Balanced Output Signal to Noise -100 dB unweighted -104 dB A weighted Dynamic Range 117 dB 10K Ohm load Phantom powered 112 dB 10K Ohm load Battery powered 111 dB 600 Ohm load Phantom powered 107.5 dB 600 Ohm load Battery powered Distortion 100 Hz .0027%, 1KHz .0028%, 10KHz .0037% Frequency Response 20Hz to 20KHz, ± 0.2 dB Gain through Unit: 6dB (Normal input, Pad switch out) Pad Switch: -20 dB attenuation Speaker Input -40 dB attenuation, equivalent to 100:1 decrease in input level -60 dB attenuation available with Pad switch Input Connectors Insulated jacks (!!!Note that the Input connector switches the unit on when a plug is inserted. Remove plug when storing to avoid battery drain!!!) Output Connector 3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold. With Audio Ground (Pin 1) lift switch Construction All-steel chassis, fibreglass PCB Battery Access Twist connector opens chassis, snap-in battery holder inside. No tools required |
Palmer PAN 03 19" DI Box 4-Channel active
Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.
Product type
DI Boxes
Type
active
Channels
4
Inputs
4
Input connectors
6.3 mm jack
Max. input level
+ 45 dBu
Input impedance
(@ 60 Hz) 1 M Ohm(s)
Input pad
0 / -30 dB
Outputs
4 (+ 4 parallel XLR outs)
THRU outputs/channel
1
Output connectors
6.3 mm jack , XLR
Max. output level
+ 10 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 20000 Hz
Transformer balanced
Yes
Ratio
10 : 1
Indicators
Power
Controls
attenuator , ground lift
Operating voltage
external
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
480 mm
Width
19 "
Depth
90 mm
Height
45 mm
Height
1 U
Weight
1,6 kg
|
You're serious about getting rid of all that excess noise on stage, but you've got so many line instruments you don't know where to start. The ADB-4 from Stewart can take care of all your high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a lot of DI power.
? Requires phantom power or 9v battery ? Ground lift switch ? Instrument or speaker level switch ? Transformerless ? Can be used with amp up to 400w ? RF shielding | Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
|
Reviews
There are no reviews yet.