Content | Specifications
Keyboard
C – C: 37-notes (3 octaves), mini keyboard designed specifically for the MS-20 mini
Manual controller
Control wheel (center click), Momentary switch -->GND
Input and Output
Signal In: Amplifier Out,
Band pass filter Out,
CV Out (0 - +8.4V),
ENV Out (0 - +5V),
Trig Out (+5V-->GND),
Signal out: Signal output (mono 1/8" mini phone jack, 2Vp-p output impedance 3.5k Ω)
Head phones: Head phones output (Stereo 1/8" mini phone jack, 33 Ω 48mW),
USB: Type B, USB-MIDI Input/Output
*Only note messages (velocity is not used) can be transmitted and received.
MIDI: MIDI Input
*Only note messages (velocity is not used) can be transmitted and received.
Power Supply
DC9V
Dimensions:
(W x D x H)
493 ×257 ×208 mm / 19.41 x 10.12 x 8.19 inches
Weight
4.8 kg / 10.58 lbs.
Accessories
AC adaptor (9V/1.7A), Patch Cord x 10
Specifications
Control Section
1. Keyboard
C – C: 37-notes (3 octaves), mini keyboard designed specifically for the MS-20 mini
2. Voltage Controlled Oscillator 1 (VCO 1)
Scale (32', 16', 8', 4') (6 octaves, +cent, -cent)
Wave form (Triangle, Sawtooth, PW-Square, White Noise) (4 modes)
Pulse width adjust 1:1 - 1:infinity
3. Voltage Controlled Oscillator 2 (VCO 2)
Scale (16', 8', 4', 2') (6 octaves, +cent, -cent)
Wave form (Sawtooth, Square, Pulse, Ring modulator) (4 modes)
Pitch (± 1 octave)
4. VCO Master control
Master tune (± 100cent)
Portamento (max. 10sec)
FFrequency modulation intensity by MG/T.EXT (-5V - +5V)
Frequency modulation intensity by EG1/EXT (-5V - 0V)
5. VCO Mixer
VCO 1 Level
VCO 2 Level
6. Voltage Controlled High Pass Filter (VCF HPF)
Cutoff frequency (50Hz - 15,000Hz)
Peak (flat - self OSC)
Cutoff frequency modulation intensity by MG/T.EXT (-5V - +5V)
Cutoff frequency modulation intensity by EG2/EXT (-5V - +5V)
7. Voltage Controlled Low Pass Filter (VCF LPF)
Cutoff frequency (50Hz - 15,000Hz)
Peak (flat - self OSC)
Cutoff frequency modulation intensity by MG/T.EXT (-5V - +5V)
Cutoff frequency modulation intensity by EG2/EXT (-5V - +5V)
8. Envelope Generator 1
Delay time (10sec)
Attack time (10sec)
Release time (10sec)
9. Envelope Generator 2
Hold time (20sec)
Attack time (10sec)
Decay time (10sec)
Sustain level (0V - 5V)
Release time (10sec)
10. Modulation Generator (LFO)
Wave form (Positive Sawtooth - Triangle - Negative Sawtooth, Wide Pulse - Square - Narrow Pulse)
Frequency (0.1Hz ~ 20Hz)
11. Manual controller
Cntrol wheel (center click)
Momentary switch -->GND
12. Power switch and Volume
Volume
13. Indicator
LED (KBD trigger, Modulation Generator rate, Power ON)
External Signal Processor
1. Control section
Input signal level
Low cut frequency (50Hz - 2,500Hz)
High cut frequency (100Hz - 5,000Hz)
CV adjust
Threshold level
2. Input and Output
Signal In
Amplifier Out
Band pass filter Out
CV Out (0 - +8.4V)
ENV Out (0 - +5V)
Trig Out (+5V-->GND)
3. Indicator (LED)
Peak indicator
Trigger indicator
Patch Panel
1. Keyboard
Keyboard control voltage output (Exponential) (0 - +8V)
Keyboard trigger output (+5V-->GND)
VCO-1 + VCO-2 control voltage input (Linear response) (0 - +8V)
VCO-2 control voltage input (Linear response) (0 - +8V)
2. VCO
VCO-1 + VCO-2 external frequency control input (OCT/V) (-5V - +5V)
3. VCF
External signal input (3Vp-p max.)
External High pass filter cutoff frequency control input (2OCT/V) (-5V - +5V)
External Low pass filter cutoff frequency control input (2OCT/V) (-5V - +5V)
4. VCO + VCF
Total external modulation input (T.EXT) (-5V - +5V)
5. VCA
External initial gain control input (0 - +5V)
6. EG
EG 1 envelope signal normal output (-5V - 0V)
EG 1 envelope signal reverse output (+5V - 0V)
EG 1 + EG 2 trigger input (-->GND)
EG 1 trigger input (-->GND)
EG 2 envelope signal reverse output (+5V - 0V)
7. MG
Triangle output (Positive Sawtooth - Triangle - Negative Sawtooth) (5Vp-p)
Rectangle output (Wide Pulse - Square - Narrow Pulse)(0 - +5V)
8. Noise Generator
Pink noise output (5Vp-p)
White noise output (5Vp-p)
9. Sample and Hold
Clock trigger input (-->GND)
Sample signal input (5Vp-p max.)
S/H output (5Vp-p max.)
10. Modulation VCA
Control voltage input (0 - +5V)
Signal input (-5V - +5V)
Signal output (-5V - +5V)
11. Manual controller
Control wheel output (-5V+5V)
Momentary switch output (-->GND)
12. Signal out
Signal output (mono 1/8" mini phone jack, 2Vp-p output impedance 3.5k Ω)
13. Head phones
Head phones output (Stereo 1/8" mini phone jack, 33 Ω 48mW)
14. USB
Type B, USB-MIDI Input/Output
*Only note messages (velocity is not used) can be transmitted and received.
15. MIDI
MIDI Input
*Only note messages (velocity is not used) can be transmitted and received.
Others
Power Consumption
9W
Power Supply
DC9V
Dimensions
(W x D x H)
493 ×257 × 208 mm / 19.41 x 10.12 x 8.19 inches
Weight
4.8 kg / 10.58 lbs.
Accessories
AC adaptor (9V/1.7A), Patch Cord x 10 | Akai Professional MCP LIVE II Overview
Building upon the success of the original MPC Live, the Akai Professional MPC Live II is a complete standalone music production workstation with an integrated sampler, sequencer, 7" touchscreen, 16 velocity-sensitive RGB-backlit pads, and 4 endless encoder "Q-Link" controls.
The MPC Live II now features a built-in dual tweeter/woofer monitoring system, allowing you to work anywhere (with or without headphones), and four stereo 3.5mm TRS CV/Gate connectors are there for interfacing with your favorite analog synthesizers, drum machines, and Eurorack modules.
The MPC 2.0 software has been updated for full MIDI Multi control, providing command over all your studio equipment. Simultaneously connect and route all the MIDI gear in your studio, including class-compliant USB Keyboards, MIDI interfaces, and USB-to-CV modules. Fuse this with deep internal MIDI routing capability across tracks, comprehensive MIDI routing to any MIDI compatible synthesizer, drum machine or sound module, and even multitrack recording capability.
The MPC Live incorporates a powerful quad-core ARM Cortex processor, 2GB of RAM, and 16GB of storage to power the MPC 2.0 software without the need to connect to a host computer. What's more, the unit can operate in Control Mode, which further expands the functionality by connecting to a computer to operate the same MPC 2.0 standalone software as a plugin in your favorite DAW. The MPC 2.0 software has powerful features including audio track recording, real-time time-stretching (audio warping), pitch-shifting, audio and MIDI drag-and-drop, clip program mode for clip launching, an updated mixer layout with advanced signal routing, and enhanced Q-Link control.
The MPC Live II features 16GB of internal MicroSD storage, includes a built-in SD card slot, and has a 2.5" SATA drive bay for adding your own SSD or HHD drive for immediate access to your own sample libraries.
The full-color 7" multi-touch screen offers quick and easy visual feedback and editing capabilities. View samples with pinch zooming, trim start and end times, and adjust and process samples on the fly. The XYFX allow you to control multiple effect parameters simultaneously, while the sequencer and mix page make short work of entering/deleting notes, editing values, and adjusting mix parameters.
The rear panel offers a comprehensive set of inputs and outputs including two 1/4" inputs and two RCA inputs with a turntable ground for sampling directly from vinyl, while the six line-level 1/4" outputs are arranged in three stereo pairs. For MIDI I/O, the unit offers two MIDI inputs and two MIDI outputs on full-sized 5-pin DIN connectors. Connect a computer via the USB Type-B connection, while two USB Type-A connectors allow for the integration of MIDI controllers to further expand your MIDI inputs, or connect thumb drives or hard-drives. A dedicated 1/4" headphone output is available for monitoring the Master L/R outputs.
The MPC Live II is premapped for Ableton Live, allowing you to take command over Live's clip launching, mixer, and instrument macro controls wirelessly via Wi-Fi network or by Ableton Link over Ethernet connection. Also included is a Splice integration for simplified sample browsing and auditioning of millions of high-quality, royalty-free samples, sounds, presets, and loops. The MPC Live II can be powered via the internal Lithium-ion battery for up to six hours or by the included power adapter. The unit also ships with a USB cable.
Specifications:
- Standalone MPC—no computer required
- Built-in monitor speakers
- MIDI multi-capable for extensive routing and MIDI multitrack recording
- 7" high-resolution multi-touch display
- 16 velocity sensitive RGB Pads
- Internal, rechargeable lithium-ion battery
- Also acts as a control surface for MPC software
- Phono and line-level inputs
- Three stereo outputs (six mono)
- Two 5-pin MIDI inputs and outputs
- 2 GB RAM, 16 GB of on-board storage
- Full-size SD card slot
- User-expandable 2.5” SATA drive connector (SSD or HDD)
- Two USB-A 3.0 slots for thumb drives or MIDI controllers
- Four TRS CV/Gate jacks, eight outputs total
- Wi-Fi and Bluetooth enabled
- Ableton Link for cross-platform collaboration
Technical specs :
Pads : 16 x Velocity- and Pressure-Sensitive Pads, RGB Backlit
8 x Banks Accessible via Pad Bank Buttons
Knobs : 4 x 360° Touch-Sensitive Q-Link Knobs for Parameter Adjustment
4 x Q-Link Knob Columns Accessible via Q-Link Button
1 x 360° Encoder for Display Navigation and Selection via Push
Buttons : 27 x Dedicated Function Buttons; Red, Amber, or Green Backlit
Display Diagonal : 6.9" / 17.6 cm (Diagonal)
W x H: 5.9 x 3.7" / 15 x 9.3 cm
Full-color LED-Backlit Display with Touch Interface
CPU Processor : Quad-Core ARM Processor
RAM : 2 GB
Storage : 16 GB (User Storage, 10 GB Preinstalled Content), 4 GB (MPC Operating System)
Connections :
- 2 x 1/4" / 6.35 mm TRS Inputs (1 Stereo Pair)
- 6 x 1/4" / 6.35 mm TRS Outputs (3 Stereo Pairs)
- 1 x 1/4" / 6.35 mm Stereo Headphone Output
- 2 x RCA Inputs (1 Stereo Pair)
- 2 x 5-Pin MIDI Inputs
- 2 x 5-Pin MIDI Outputs
- 4 x Stereo CV/Gate Outputs
- 1 x Ethernet Link Port
- 2 x USB Type-A Ports
- 1 x USB Type-B Port
- 1 x SD-Card Slot
- 1 x Power Adapter Input
Power Power Adapter : 19 V, 3.42 A, Center-Positive, (Included)
Battery : Lithium-Ion, Rechargeable, up to 5 Hours of Battery Life
Dimensions : (W x D x H) 16.2 x 9.6 x 1.8" / 41.6 x 24.4 x 4.6 cm
Weight : 7.5 lb / 3.4 kg |
Powerful analog bass sound creation and an Electribe-inspired sequencer for the ultimate bass lines
Aggressive sounds that stand up to the drums; fat sounds that support the rhythm; funky sounds that generate a groove - the volca bass is an analog bassline groove box that has what you need for a wide range of bass lines.
Although simple in structure, the analog sound engine has an unmistakable presence with subtle nuances that cannot be reproduced by a digital simulation; it's a great choice for acid house and many other styles of music. The step sequencer distilled from the Electribe is not only visually intuitive; it's also a powerful way to generate "free form" bass loops that will stimulate your inspiration.
Keyboard
Multi touch Keyboard / step key
Synthesizer
Type
Analog synthesis
Structure
3VCO, 1VCF, 1VCA, 1LFO, 1EG
VCO Wave
Saw, Square
VCF
Cutoff, Peak, EG Int
VCF Type
Low Pass Filter, 12 db/oct
VCA
EG on/of, Sustain on/off
LFO
Rate, Int, Target (Amp, Pitch, Cutoff), Wave (Triangle, Square)
EG
Attack, Decay/Release, Sustain
Sequencer
Number of parts
3
Number of Steps
16
Number of Recording Patterns
8
Connectors
Audio Output
Headphones (3.5mm stereo mini jack)
Sync
Sync In (3.5mm monaural mini jack, Maximum input level: 20V)
Sync Out (3.5mm monaural mini jack, Maximum Output level: 5V)
MIDI
In
Power
Battery Life
Approximately 10 hours (using alkaline batteries)
Power supply
AA alkaline battery ×6
AA nickel-metal hydride battery ×6
AC adapter "KA-350” (optional)
Others
Accessories
AA alkaline battery ×6 (for verifying operation)
Options
AC adapter "KA-350”
Dimensions
(W x D x H)
193 × 115 × 46 mm / 7.61 x 4.54 x 1.82 inches
Weight
370 g / 0.82 lbs (Excluding batteries)
| The X is a standalone MPC featuring a beautiful, full color 10.1” multi-touch screen, 16 amazingly responsive, velocity- and pressure-sensitive RGB pads and 16 gigs of internal storage. To make it a truly untethered, computer-free experience, the X also features two USB slots that can be used for MIDI controller connectivity.
MINIMUM COMPUTER SPECS:
- Controller Mode: Windows 8.1 or newer
- Controller Mode: Mac OS X 10.10.5 or newer
- MPC 2.0: Minimum 2GB free disk space (20GB for all content), Minimum 4GB RAM (8GB recommended), Minimum Dual-core 2.5GHz CPU
|
MAIN FEATURES
- 6-channel Modeling Percussion Synthesizer
- Integrated multipad, kick pad input and MIDI NEW
- Simplified user interface with easy sound selection NEW
- New preset 'Drum Select' library for kicks, snares, toms and more NEW
- Advanced sound engine with Resonant Synthesis, Subtractive synthesis and FM-synthesis
- Reverb and Delay Effects - adjustable amount for each pad NEW
- Drive, Sample-Rate reduction, Ring Modulation and EQ-effects for each pad
- MIDI in/out and full CC-control
- Stereo Output with improved output level
- Headphone Output with improved output level
INTEGRATED MULTIPAD NEW
The ultra compact new Nord Drum 3P features an integrated super responsive multipad and external kick input and weighs under 2 kg (4,1 lbs)!
DELAY AND REVERB EFFECTS NEW
The great sounding global Stereo Reverb and Delay effects lets you add a whole new dimension to your drum sounds and the effect amount is easily adjusted for each drum channel.
SIMPLIFIED SOUND SELECTION AND NEW SOUND BANK NEW
The new Drum Select feature lets you browse a wide selection of great sounding drums sounds, simply assigned to each pad individually. Easily replace toms, cymbals or kicks in seconds by selecting from our new preset library.
The new Drum Select banks feature 9 categories of great preset sounds that can be easily assigned to any of the six pads/channels - and is a great starting point in rehearsal situations when you need to find the right sounds in a matter of seconds.
The categories include Bass drums, Snare drums, Toms, Hi-hats, Cymbals, Percussion, Bells, Tuned Percussion and Effects.
|
The P-10 is one of the popular EDIROL PR Video Presenter Series. The P-10 Visual Sampler is the newest, compact and most affordable offering in the growing lineup of EDIROL visual performance products. Although many presenters and visual artists use computers for their video and still-frame playback, they are limited in accessibility, reliability, control and triggering content.
* Capture video with immediate playback with effects
* Easy and intuitive operation
* Both video and stills can be triggered
* Slide show function to make movies from stills
* Solid state SD(HC) storage media
* Remote controllable via V-LINK
p10_sd_card_sm The P-10 provides a solution to all of these issues in a number of ways. Being equipped with 12 keypads, dedicated knobs and dials, the user has tactile control and accessibility to all their material. The P-10 uses SD and SDHC memory cards for solid state, reliable storage and supports motion jpeg and still jpeg formats. A bright color LCD display enables viewing with no need for an external monitor. Being a dedicated hardware device, the P-10 is very stable and is not susceptible to stuttering, virus or hardware and software compatibility issues inherent with computers.
Analog capture inputs provide a quick and easy way to directly capture content to the P-10 and then immediately play it back with effects enabled to wow the crowd. Additionally, the slide show function allows the piecing together of still images to create movie type playback or give the feel of stop motion animation.
The P-10 is the ideal solution for corporate presentations, VJʼs, clubs, houses of worship and sporting events. The sleek and compact design lends itself to portable applications, as well as permanent installations when size and space are considerations. |
Reviews
There are no reviews yet.