MACKIE MDB-USB STEREO DIRECT BOX

Passive Stereo Direct Box with USB

• High resolution 24bit / 96kHz interface
• 2x balanced, low-impedance XLR outputs with ground lift
• Output level control with mono switch
• Headphone output for easy listening
• Noiseless operation
• Plug-and-play operation, no driver required

You're serious about getting rid of all that excess noise on stage, but you've got so many line
instruments you don't know where to start. The ADB-4 from Stewart can take care of all your
high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes
up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a
lot of DI power.

? Requires phantom power or 9v battery
? Ground lift switch
? Instrument or speaker level switch
? Transformerless
? Can be used with amp up to 400w
? RF shielding

Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

Phantom or battery powered in a rugged steel chassis
 
The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in
a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo
D.I. concepts.

Precision engineered
Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade
components, plus an all-steel chassis gives excellent hum and noise specifications and superb
audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps
the stereo image centred.

Level control
The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced
XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications
from the softest keyboard to the hottest broadcast levels.
 
Battery compartment
The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing
extremely easy, even on the darkest stages.
A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip
leads to break, no tools required, no screws to lose. Production crew heaven!
 
Automatic Phantom switching
The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED
will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.

Rugged all-steel case
A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer
chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that
is hard to dislodge, and hard to leave behind.
 
Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus
phantom power On LED and captive screw for opening up the unit for battery changing
 
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all
the dynamics,clarity and stereo information of the original sound source transferred to the mixing console.
The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal
balancing requirements.
 
T E C H N I C A L S P E C I F I C A T I O N S:
Max Input Level
+12 dB Phantom powered
+6 dB Battery powered
Input Impedance 1 Meg Ohm
Max Output Level
+17 dB 10K Ohm load Phantom powered
+12 dB 10K Ohm load Battery powered
+11 dB 600 Ohm load Phantom powered
+12 dB 600 Ohm load Battery powered
Output Impedance 680 Ohms Balanced
Output Signal to Noise
-100 dB unweighted
-104 dB A weighted
Dynamic Range
117 dB 10K Ohm load Phantom powered
112 dB 10K Ohm load Battery powered
111 dB 600 Ohm load Phantom powered
107.5 dB 600 Ohm load Battery powered
Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056%
Frequency Response 20Hz to 20KHz, ± 0.2 dB
Gain through Unit: 6dB (Pad switch out)
Pad Switch: Global -20 dB attenuation
Input and Loop Out Connectors
Insulated jacks (!!!Note that Channel A Input connector switches the unit on
when a plug is inserted. Remove plug when storing to avoid battery drain!!!)
Output Connectors
3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold.
Global Audio Ground (Pin 1) lift switch
Construction
All-steel chassis, fibreglass PCB
Battery Access
Twist connector opens chassis, snap-in battery holder inside.
No tools required

At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.

Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.

As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB12 is for you.

• Phantom Powered
• Green LED Phantom Power Indicator
• +48V Phantom Operation
• Low-Noise Active Circuitr

Input: 1 instrument/line/speaker level

Connector: 1/4" jack

Type: Unbalanced, RF filtered

Impedance: 150k Ohm typical

Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)

Thru Output: 1 parallel connection from input jack

Connector: 1/4" jack

Type: Unbalanced, RF filtered

Main Output: 1 line level

Connector: XLR male jack

Type: Balanced

Impedance: 150 Ohm typical

Max Output Level: 0dBu

Transformer: Custom dbx mu-metal-shielded

Frequency Response: 20Hz to 20kHz, +/-2.5dB

Noise:

THD:

Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)

Weight: 1.4 lbs / 0.65 kg

Note: Specifications subject to change without notice.