Content |
2x2-way recessed ceiling speaker
As a recessed ceiling speaker, the ICP 262 has a special place in the Interior Performance series. It has two 19 mm tweeters arranged at a fixed angle and 3-way treble level adjustment. Due to the dual voice coil, the ICP 262 can run in both mono and stereo mode. As a result, most installation situations can be handled successfully.
Thanks to the coated surface of the cone and high-quality components, installation in humid areas such as in bathroom or near a swimming pool is no problem. In addition, installation with the help of the rugged clamping mechanism is easy.
Principle
2 x 2 way in-wall/in-ceiling loudspeaker
Equipment
2 x 19 mm tweeter
160 mm woofer
Power Handling (RMS / Max.)
70 / 120 watts
Sensitivity (2.8V/1m)
90 dB
Impedance
2 x 8 Ohm
Frequency Response
36 – 24000 Hz
Crossover Frequencies
4.000 Hz
Recommended Amplifier Output
20 - 140 Watts
Outer Dimensions Ø
233 mm
Cutting Out Ø
198 mm
Mounting depth
88 mm
Weight
1.3 kg
|
- Frequency Range (-10 dB) : 34 Hz – 18 kHz In half space (in ceiling)
- Frequency Response (±3 dB) : 47 Hz – 16 kHz In half space (in ceiling)
- Coverage Pattern : 90° conical, broadband (Avg 1k - 16kHz) Average 1 kHz to 10 kHz
- Directivity Factor (Q) : 8.7 (1k - 16kHz)
- Directivity Index (DI) : 9.4 dB (1k - 16kHz)
- Long-Term System : 250 W (1000 W peak), 2 hrs
- Power Rating, IEC3 : 150 W (600 W peak), 100 hrs
- Sensitivity (2.83V@ 1m) : 94 dB measured half-space, 99 dB computed for competitive comparison
- Maximum SPL6 : 118 dB cont ave (124 dB peak)
- Crossover Network : 1.8 kHz, 3rd order (18 dB/oct) high-pass plus conjugate to HF, 2nd order low-pass to LF.
- Nominal Impedance : 8 ohms
- Transducer Low Frequency Driver : Kevlar reinforced cone, 50 mm (2 in) voice coil.
- Transducer High Frequency Driver : JBL 2412H-1 compression driver, 25 mm (1 in) voice coil.
- Input Connector : Removable locking connector with screw-down terminals. Max wire 12 AWG (2.5 mm2)
- Dimensions (H x W x D) : 366 x 366 mm (14.4 x 14.4 in) square baffle x depth from back of baffle of 223 mm (8.8 in) on 321C
- Net Weight : 16.0 lbs. (7.3 kg)
- Shipping Weight : 19.4 lbs. (8.8 kg)
|
Driver Complement
Mid/Woofer 1 - 6-1/2" Diameter (16.51cm)
Dynamic Balance polymer composite cone driver
Tweeter 2 - 3/4" Diameter (1.91cm)
Silk Dome Tweeters
Electrical
Overall Frequency Response 40Hz-20kHz
Lower -3dB Limit 55Hz
Upper -3dB Limit 20kHZ
Nominal Impedance 8 ohms
Recommended Amplifier Power 20 - 100 w/channel
Efficiency 89 dB
Dimensions
Overall Diameter 8-15/16“(22.70cm)
Cut-out Diameter 7-5/8“(19.37cm)
Mounting Depth
(assumes 1/2" [12.7mm] wall material) 2-5/8" (6.67cm)
Overall Depth 3-1/8" (7.94cm)
Shipping/Other
Shipped As each
Product Weight 2.55 lbs. (1.16kgs) each
Total Shipping Weight 3.00 lbs. (1.36kgs)
Speaker Warranty Lifetime Warranty
| * Driver Size (dual-cone) 200 mm (8 in)
* Driver Sensitivity (mid-range) (1W [2.83V], 1m, 2k - 6k Hz) 97 dB
* Frequency Range (-10 dB) Driver/Grille Assembly: 50 Hz - 17 kHz
o Installed in CSS-BB backcan: 90 Hz - 17 kHz
* Coverage (2 kHz) 110°
* Driver Continuous Power Handling 20 Watts
* 100V Taps 10W, 5W, 2.5W
* 70V Taps 10W, 5W, 2.5W, 1.3W
* 25V Taps 10W, 5W, 2.5W, 1.3W
* Transformer Insertion Loss 1.5 dB Maximum
* Transformer Connection Bare wire
* Motor Mass 283 g (10 oz)
* Safety Agency: Suitable for use in air handling spaces per UL1480, UL2043, NFPA 90 & NFPA 70, when installed with corresponding UL Listed backcan, below. S7232/UL Listed, Signaling Speaker. Transformer UL registered per UL1876. In accordance with IEC60849/EN60849.
* Matching CSS Backcan CSS-BB8 (0.15 cu ft)
* Bolt Mounting Circle to Backcan 4 points on 286 mm / (11.25 in) diameter
* Cutout Diameter
o Open-back: 216 mm (8.5 in)
o In CSS-BB backcan 295 mm (11.7 in)
* Depth (behind grille) 73 mm (2.9 in)
* Grille Diameter 327 mm (12.9 in)
* Net Weight (ea) 1.58 kg (3.5 lb)
* Shipping Weight (ea) 2.25 kg (5.0 lb)
* Included Accessories 4 pcs M4 x 40 mm sheet metal screws for attaching speaker/driver/transformer assembly to corresponding backcan. |
Outer Flange Diameter | Metric :8-3/4” | 22.2 cm
Cut Out Diameter | Metric :7-5/8” | 19.4 cm
Depth from Flange | Metric :4-1/4” | 10.8 cm
Driver Complement :One 1" pure aluminum dome pivoting tweeter coaxially mounted in a 6-1/2" bass/midrange driver
Frequency Response :28 Hz – 30 kHz
Impedance :Compatible with 8 Ohm outputs
Recommended Associated Amplifier Power :10 – 200 watts
A/V Receiver Crossover Setting :100 Hz
Inputs :One pair of 5 way binding posts
Available Finishes :Paintable White
Packaging :Two to a carton
Weight | Metric :6 lbs | 2.7 kg
Warranty :5 Years |
Key Features:
Clear, High-Fidelity Performance
6W Transformer for use on 70V / 100V
Distributed Lines
Dog-Ears for Easy Blind Mount
Installations
High Sensitivity for Maximum Power
Efficiency
Open-back design for applications not
requiring an in-ceiling backcan.
Specifications (8128):
Component: 200 mm (8 in) Full-Range
Frequency Range (-10 dB): 50 Hz – 16 kHz
Coverage: 90° conical
Sensitivity (2.83V@ 1m): 97 dB (1 kHz - 8 kHz)
Termination: Bare Wire
Nominal Driver Impedance: 8 ohms
Driver Power Capacity: 25 W
70V/100V Transformer Taps: 6 W, 3 W, 1.5 W, (0.75 W at 70 V only)
Dimensions (Diameter x Depth): 287 mm (11.3 in) diameter round baffle x 104 mm (4.1 in)
depth from back of baffle
Cutout Dimension: 260 mm diameter (10.1 in)
Net Weight: 1.4 kg (3.0 lb)
Included Accessories: Sculpted Grille
Optional Accessories: MTC-8128C C-ring
MTC-RAIL tile rails
Plenum Usage: Not intended for use in return air plenums
|
Reviews
There are no reviews yet.