Content |
Professional amplifier - 600W RMS each channel on 8 Ohm - 850W RMS each channel on 4 Ohm - 1100W RMS bridge power on 8 Ohm - Frequency response: 10-50.000 Hz - Input sensitivity: 0,775V - Signal/noise rate: >100dB - Segregation ratio: >105dB - Dumping factor: >500 - Input impendance: 20Kohms - Slew rate: 55V/microsec. - Thermal protection, short circuit, overload - Ground/Lift switch - XLR, Jack 6.3 mm inputs - Speakon, binding connector output - Dimensions: 482 x 453 x 88 mm - Weight: 19kg - Package: 1 piece each box
|
InterM V-2000 Power amplifier 2Χ550W/4ohm, 2Χ300W/8ohm, 2Χ900W/2ohm bridge 1900W/4ohm |
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 800 Watt rms | | Power output stereo 4Ω: | 2 x 650 Watt rms | | Power output stereo 8Ω: | 2 x 350 Watt rms | | Power output bridged 4Ω: | 1600 Watt rms | | Power output bridged 8Ω: | 1300 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 103 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 7.5 A | | Power Consumption: | 2700 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 19.5 / 42.98 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 150 / 5.9 mm/inch | | Package width: | 555 / 21.85 mm/inch | | Package depth: | 525 / 20.66 mm/inch | | Shipping Weight: | 20 / 44.09 Kg/Lbs |
| Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 1800 W, 4 Ω - 1200 W, 8 Ω - 750 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 3400 W, 4 Ω - 1800 W, 8 Ω - 950 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 3600 W, 8 Ω - 2400 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +6.6 dBu (1.66 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class H Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 17.7 kg (39.0 lbs) |
Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps. | L1800 600W-600W 4ohm (360W-360W 8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
Reviews
There are no reviews yet.