| Content | PA amplifier with MP3 player, radio FM and Bluetooth
- Speaker output 70/100V or 4/16 Ohm
- Output power 120 W RMS
- Six separate zone volume control
- Control display with USB / SD card inputs and radio FM
- Three microphone inputs
- Three auxiliary inputs
- One aux output
- Priority microphone with mute function
- Individual volume control, low and high tone control
- Output circuit shorting protection
- Remote control included
- Dimensions: 480 x 380 x 88 mm
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 200: 2x 100 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 15 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier. |
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
| Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | | Current Consumption | 30 mA or less | | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | | Finish | Panel: Surface-treated steel plate | | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | | Weight | 50 g | | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
| - Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 2.2A or less at rated power output. | | Output Power | Rated 15W, max. 35W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency Response | 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 132mm (mounting device excluded) | | Weight | 900g | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (4A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
Reviews
There are no reviews yet.