Content |
STEREO MODE: 2 x 650W @ 8Ω. 2 x 1050W @ 4Ω. 2 x 1350W @ 2Ω.
BRIDGE MODE: 2200W @ 8Ω. 3000W @ 4Ω.
PROTECTIONS: Soft start DC, short circuit, over load, clip limit, over heat,
progressive volume, VHF. Weight 9.7 kg.
Dimension W 483 x H 89 x D 450 mm.
Assembled in China. Engineered by Montarbo. |
Manufacturer |
LAB GRUPPEN |
Warranty |
10 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
4Ω / 16Ω |
Resistance ohms |
2Ω |
Power (8 ohms/Watt RMS) per channel |
1450 |
Power (4 ohms/Watt RMS) per channel |
2800 |
Power (2 ohms/Watt RMS) per channel |
3500 |
Weight (kg) |
12 |
|
Low weight switching final power amplifier. Power 2X3500W / 4Ω, 2Χ4700W / 2Ω. 7000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. LevelMAX peak voltage and RMS compressing, limiting, New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front panel. USB input on the front panel for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg | L2400 750W-750W 4ohm (500W-500W 8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
Features
• The Macro-Tech® i Series continues the Crown®
Macro-Tech legacy of unparalleled sonic accuracy and
detail, putting sound quality above all else
• Patented, cutting-edge Class-I circuitry gets more
power out of an amplifi er with less waste
• Rugged construction ensures that all Macro-Techs are
built to withstand years of abuse on the road
• Global Power Supply — designed to deliver maximum power
no matter what country you work in
• Built-in load, line voltage, input and output monitoring
• Standard Ethernet networking via System Architect® lets
system operators monitor and control the amplifi er from any
location
Specifications
Performance
Frequency Response (at 1 watt, 20 Hz - 20 kHz
into 8 ohms): ±0.25 dB.
Signal to Noise Ratio (below rated full-bandwidth
power, A-weighted): > 110 dB.
Total Harmonic Distortion (THD) (at 2 watts into 8
ohms):
Total Harmonic Distortion (THD) Plus Noise (at
full rated power):
Intermodulation Distortion (IMD) (60 Hz and 7
kHz at 4:1, from full rated output to –30 dB):
Damping Factor (20 Hz to 100 Hz at 8 ohms):
> 5000.
Crosstalk (below rated power, 20 Hz to 1 kHz):
> 80 dB.
Common Mode Rejection (CMR) (20 Hz to 1
kHz): 55 dB, typically >70 dB.
DC Output Offset (shorted input):
Input Impedance (nominal): 10 kilohms balanced,
5 kilohms unbalanced.
Maximum Input Level: +20 dBu typical.
Network: Onboard HiQnet™, compatible with
standard 100 Mb Ethercom hardware.
Load Impedance: (Note: Safe with all types of
loads)
Stereo: 1/2/4/8/16 ohms.
Bridge Mono: 2/4/8 ohms.
Input Sensitivity (referenced to 8 ohm rated
output): 1.4V, 32 dB gain, and 26 dB gain.
Voltage Gain (referenced to 8 ohm rated output):
MA-5000i: 37.1 dB to 22.2 dB
MA-9000i: 37.9 dB to 23.0 dB
MA-12000i: 39.3 dB to 24.5 dB
Required AC Mains: Universal AC input, 100-
240VAC, 50/60 Hz (±10%). Maximum AC mains
voltage 264VAC.
AC Line Connector: Five cordsets supplied with
amplifi er (USA, UK, European, Australia, India).
|
Manufacturer |
POWERSOFT |
Warranty |
4 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
8Ω / 4Ω / 2Ω |
DSP |
Yes |
Power (8 ohms/Watt RMS) per channel |
1300 |
Power (4 ohms/Watt RMS) per channel |
2500 |
Power (2 ohms/Watt RMS) per channel |
3000 |
Weight (kg) |
7 |
|
Reviews
There are no reviews yet.