Content |
STEREO MODE: 2 x 850W @ 8Ω. 2 x 1400W @ 4Ω. 2 x 2300W @ 2Ω.
BRIDGE MODE: 3000W @ 8Ω. 4600W @ 4Ω.
PROTECTIONS: Soft start DC, short circuit, over load, clip limit, over heat,
progressive volume, VHF. Weight 13 kg.
Dimension W 483 x H 89 x D 505 mm.
Assembled in China. Engineered by Montarbo. |
Power Output Level: QD4480
8ohm (Quad Ch) 80W
4ohm (Quad Ch) 120W
8ohm bridged mono 240W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
Τελικός Ενισχυτής Switching, ισχύος 2X3000W/4Ω, bridged 6000W/4Ω, με ενσωματωμένο επεξεργαστή DSP με έτοιμα preset για διάφορα ηχεία, EQ, limiting, compression, delay, crossover frequencies και subharmonic synthesizer για κάθε κανάλι. Είσοδοι τύπου Phoenix & HD-15, έξοδοι τύπου Barrier Strip, διαχείριση μέσω με Η/Υ (USB) συμβατότητα με HiQnet. Κατάλληλος για κινηματογραφική χρήση, 15 έτοιμα εργοστασιακά preset για κινηματογραφικά ηχεία JBL. Βάρος 10,6 Kg. |
Low weight switching final power amplifier. Power 2X3500W / 4Ω, 2Χ4700W / 2Ω. 7000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. LevelMAX peak voltage and RMS compressing, limiting, New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front panel. USB input on the front panel for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg |
Engineered from the ground up for unmatched quality and performance, the Crown? DSi Series of power amplifiers offers three models of 500W, 800W, and 1200W per channel at 4 ohms. Onboard digital signal processing includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15 connector provides easy input/output connectivity between DSi amplifiers and the new DSi-8M System Monitor. The intuitive front panel LCD screen guides installers through a setup process? featuring presets for the industry-standard JBL cinema loudspeaker systems? to make configuration quick and easy. At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched performance with each award-winning JBL ScreenArray? system, making this the ultimate cinema solution.
Features : Includes three models of 500W, 800W, and 1200W per channel at 4 ohms Automatic presets for popular JBL cinema speaker systems for quick, easy configuration Intuitive front-panel LCD screen guides installers through setup Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting Computer connectivity via USB allows fast setup and configuration with HiQnet? System Architect? software Rear-panel HD-15 connector provides easy input/output connectivity between DSi amplifiers and new DSi-8M System Monitor Switch-mode universal power supply All products fill 2U rack spaces and weigh under 19 pounds Barrier strip outputs, removable Phoenix-style input Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifi er and the DSi-8M System Monitor. The outputs shall be usable as stereo or bridged-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. Front panel controls and indicators shall include the following: Level: Detented rotary level control, one per channel. Power Switch: On/off switch applies AC power to the amplifi er. Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items. LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing. Signal Indicator: Green LED, one per channel, fl ashes when a very low-level signal is present at input. ?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below clip. ?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB below clip. Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is ready to produce audio. Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion. Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions. Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power. Rear panel controls and connectors shall include the following: AC Line Connector: NEMA 5-15P (15A). Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal. Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker. HiQnet USB Connector: Type B, connects to a HiQnet network. HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor. The amplifi er shall have the following specifi cations: Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo (per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with 0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono: 1,000W with 0.5% THD. Voltage Gain at 1kHz, 8 ohm rated output: 26 dB. Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity at 8 ohm rated output: 2.35V. Sensitivity at 4 ohm rated output: 2.24V. Sensitivity at 2 ohm rated output: 1.88V. Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 500 Hz. Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz. Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical. AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V, 50/60 Hz. AC Line Current: 6.5A. At Idle: Draws no more than 90 watts. Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing). The DSP section shall have the following specifi cations: EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also adjustable high and low shelving fi lters. Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per channel. Delay: Up to 50 msec total delay per channel. Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6, or ?12 dB threshold per channel. Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL system presets. Protection shall include the following: DSi-Series amplifi ers shall be protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; excessive output current, and input overload damage. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients The chassis shall be steel. Cooling shall be by a proportional speed fan with front-to-rear airfl ow. Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface. Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg) |
Manufacturer |
LAB GRUPPEN |
Warranty |
10 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
4Ω / 16Ω |
Resistance ohms |
2Ω |
Power (8 ohms/Watt RMS) per channel |
1450 |
Power (4 ohms/Watt RMS) per channel |
2800 |
Power (2 ohms/Watt RMS) per channel |
3500 |
Weight (kg) |
12 |
|
Reviews
There are no reviews yet.