Content | Stay in the groove with this replacement ceramic cartridge!
Your cartridge and stylus are where the rubber hits the road on your turntable. Or should we say, where the needle hits the record.
This replacement ceramic cartridge is a perfect fit for your Classic LP, iPT01, iPTUSB, iPTUSB LE, Max LP, or Mobile LP and many other ION turntables (see list). If your stylus is worn, or if you just need a backup, this cartridge will keep your turntable in top shape and sounding great!
To Replace Stylus
- Grasp both sides of the stylus and pull forward to remove stylus
- Grasp both sides of the stylus and slide up and back to attach stylus
To Replace Cartridge
- Remove stylus from old Cartridge
- Grab headshell with thumb under front tab and index finger on rear of head shell with left hand.
- Grab old cartridge with right thumb and index finger. Carefully Pull down and forward with right hand while while pulling up with left hand.
- Carefully disconnect wires from rear of cartridge pulling from metal tabs.
- Remove stylus guard and stylus from new cartridge
- Connect wires on new cartridge. the single metal connector with black wires goes on the bottom posts that are closer together.
- From rear view, as you would install the cartridge - The red wire goes on the right upper post, the white wire goes on the left upper post.
- Reconnect cartridge to headshell by placing cartridge beneath headshell with thumb below cartridge and index finger on top of headshell.
- Carefully squeeze the two together. a \'light\' snap occurs and the cartridge should fit snug.
- Reattach new stylus to new cartridge.
Fits all ION turntables that use a ceramic cartridge (see following list):
- Classic LP
- Max LP
- Mobile LP
- iPTUSB
- Archive LP
- Forever LP
- Live LP
- Power Play
- Quick Play Flash
- Quick Play LP
- Vinyl Motion
- Vinyl Motion Deluxe
- Air LP
- Duo Deck
- iLP
- LP 2 GO
- CD Direct
- iProfile
- Profile LP
- Profile Pro
*TTUSB, TTUSBDC, LP2CD, Select LP use a magnetic cartridge and are not compatible. |
A revolutionary new high performance cart for DJs! Exceptional tracking ability of 120 μm!
The Ortofon-Serato S-120 represents a completely new way of constructing and designing cartridges. Its breakthrough patent pending technology has been designed to provide maximum freedom for DJ performance.
An innovative technology, called asymmetric suspension, takes the cartridge performance to the next level.
Its superior tracking force ensures the S-120 stays in the groove even under extreme live performance conditions.
In addition, its design achieves an unprecedentedly low level of record wear, which helps protect your valuable vinyl. On top of this, the S-120 is capable of providing a level of sound quality never thought possible from a modern DJ cartridge.
Output voltage at 1000Hz, 5cm/sec.
|
10 mV
|
Channel balance at 1kHz
|
1,5 dB
|
Channel separation at 1kHz
|
20 dB
|
Channel separation at 15 kHz
|
15 dB
|
Frequency range at -3dB
|
20-18.000 Hz
|
Frequency response
|
20-18.000 Hz +3/- 2dB
|
FIM distortion at recommended tracking force DIN 45.542
| |
Tracking ability at 315 Hz at recommended tracking force
|
120 μm
|
Compliance, dynamic lateral
|
11 μm/m N
|
Stylus type
|
Spherical
|
Stylus tip radius
|
R 18 μm
|
Tracking force range
|
1,5-10,0 g (15-100 mN)
|
Tracking force recommended
|
4,0 g (40 mN)
|
Internal impedance, DC resistance
|
1680 Ohm
|
Internal inductance
|
920 mH
|
Recommended load resistance
|
47 kOhm
|
Recommended load capacitance
|
200-600 pF
|
Cartridge weight
|
5 g
|
Replacement stylus unit
| Ortofon-Serato S-120 |
| The MC 1 Turbo is an excellent entry into the world of high output moving coil (MC) cartridges, with an elliptical stylus profile. The MC 1 Turbo has a 3.3mV output, which makes it perfect for use with inbuilt phono preamps – specifically ones designed for moving magnet (MM) cartridges. The MC 1 Turbo provides a taste of the linearity and precision of moving coils, but without the need for additional high gain preamps or transformers.
Technical data |
|
Output voltage at 1000 Hz, 5cm/sec. |
3,3 mV |
Channel balance at 1 kHz |
|
Channel separation at 1 kHz |
> 22 dB |
Channel separation at 15 kHz |
> 15 dB |
Frequency range at - 3dB |
20-25.000 Hz |
Frequency response FIM distortion at recommended |
20-20.000 Hz + 4 / - 1 dB |
Tracking ability at 315Hz at recommended tracking force *) |
> 65 µm |
Compliance, dynamic, lateral |
13 µm/mN |
Stylus type |
Elliptical |
Stylus tip radius |
r/R 8/18 µm |
Tracking force range |
1,8-2,2 g (18-22 mN) |
Tracking force, recommended |
2 g (20 mN) |
Tracking angle |
20° |
Internal impedance, DC resistance |
100 Ohm |
Recommended load impedance |
47 kOhm / |
Cartridge body material |
Noryl |
Cartridge colour |
Black |
Cartridge weight |
4,1 g |
|
Type: MC-type
Playback frequency range: 15-50,000Hz
Output voltage: 0.3mV (1kHz and 3.54cm/sec.)
Channel separation: 30dB (1kHz)
Output balance: 0.5dB (1kHz)
Stylus pressure: 1.8-2.2g (2.0g standard)
Coil impedance: 10O (1kHz)
DC resistance: 10O
Load resistance: More than 100O (when head amp connected)
Coil inductance: 22µH (1kHz)
Static compliance: 40×10-6cm/dyne
Dynamic compliance: 10×10-6cm/dyne (100Hz)
Stylus needle shape: Oval (0.3×0.7mil)
Cantilever: Duralumin tapered pipe
Vertical tracking angle: 23°
Dimensions: H16×W16.6×D26.5mm
Weight: 6.9g
Accessories: Non-magnetic screwdriver × 1, Washer × 2, Protector × 1, Cartridge installation screws 13 mm × 2 and 19 mm × 2, Nut × 2, Brush × 1, PCOCC lead set × 1
|
Ortofon D 25 M Mono Cartridge Spherical Diamond
OM D 25 M Technical Data:
Output voltage at 1000 Hz, 5cm/sec.: 4 mV, Lateral (mono)
Channel balance at 1 kHz
Channel separation at 1 kHz
Channel separation at 15 kHz
Frequency range: 20-20.000 Hz
Frequency response: 20-18.000 Hz +3 / - 2 dB
FIM distortion at recommended tracking force, DIN 45.542:
Tracking ability at 315Hz at recommended tracking force: > 70 µm
Compliance, dynamic, lateral: 7 µm / mN
Stylus type: Spherical
Stylus tip radius: R 25 µm
Equivalent stylus tip mass: 0,5 mg
Tracking force range: 2,0-3,0 g (20-30 mN)
Tracking force, recommended: 2,5 g (25 mN)
Tracking angle: 20°
Internal impedance, DC resistance: 750 Ohm
Internal inductance: 450 mH
Recommended load resistance: 47 kOhm
Recommended load capacitance: 200-600 pF
Cartridge colour, body/stylus: Black/Black
Cartridge weight: 5 g
Replacement stylus unit: Stylus D 25 M
|
| M44-7
Revived exactly the same as the original, this legendary battle needle offers ultra-high skip resistance and ultra-high output. The needle of choice for many champion DJ's worldwide. Engineered for scratch DJ's and turntablists, the M44-7 is designed not to skip under even the most demanding circumstances.
- Combining the Shure unique wide-diameter Type S cantilever with a tracking force of 1.5 to 3.0 grams, the M44-7's rugged construction is highly durable, but will not unduly wear your vinyl.
- With a 9.5 mV output, the M44-7 produces powerful, resonant sound.
- Skip Resistance: ultra high
- Output: ultra high
- Record Wear: ultra low
- Sound Emphasis: big bass
Tone Arm MountStandard 1/2 inch Cartridge TypeMoving Magnet Output VoltageTypical at 1 kHz9.5 mV RMS at 5 cm/sec peak velocity Recommended Load47 kilohms in parallel with 450pf Tracking ForceEffective at stylus tipRange: 1.5 to 3 grams Stylus CantileverShure Type SHeat-treated aluminum alloy / tubular1.6 mil wall thickness / 34.5 mil diameter Diamond Stylus TipPolished natural gemstone: SphericalRadius: 0.7 mil Frequency ResponseEssentially flat from 20 to 20,000 Hz
Stereo Channel BalanceWithin 2 dB Channel SeparationTypical at 1 kHz: 20 dB Net Weight6.7 grams Height15.9 mm Accessories IncludedAttached flip-down Stylus GuardHeadshell Screwdriver (Phillips)Extra Set of 4 Headshell Wires (4-99)Stylus Cleaning BrushHeadshell Weight (3 grams)User GuideMounting hardwareStylus guard Replacement NeedlesSingle with box & User Guide N44-74 Pack mounted on a card N44-7Q12 Pack mounted on a card N44-7Z
Made In Mexico |
Reviews
There are no reviews yet.