| Content |
The MYMonitorII allows blending of any microphone source with any stereo source in a convenient personal monitoring solution. The microphone thru provides direct connection to any mixer and will pass phantom power from the board for powering condenser microphones. Built for maximum flexibility, the ARTcessories MyMonitorII can be powered with the supplied 12vDC power supply, or from an internal 9v battery.
The pop-less microphone on/off switch lets you locally mute the microphone. The headphone section has independent 1/8-inch and ¼-inch TRS outputs with plenty of drive for both.
- Blends any Microphone, Instrument and Stereo Source for Personal Monitoring
- Microphone Input and Thru with Pop-less On/Off Mute Switch
- Passes Phantom Power for Operation with Condenser Microphones
- Instrument/Line Input and Thru Jacks
- Stereo Monitor Input with Blend Control
- Headphone output section has 1/8-inch and 1/4-inch Jacks
- High Performance, Low Noise Circuitry
- 9v battery and 12vDC Power Operation
| The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped.
In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation.
A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback.
The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
- Model Name: LDHPA1
- Product Type: headphone amplifier
- Type: 1-channel stereo
- Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
- Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
- Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
- Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
- Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
- Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
- Headphone Outputs: 1
- Headphone Output Connectors: 3.5 mm stereo jack
- Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
- Minimal Connected Impedance per Channel: 16 ohms
- Frequency Response: 20 Hz - 40,000 Hz
- THD 1 kHz Sine: 0.04%
- Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
- Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
- Power Supply: 9 V DC block battery, DC jack
- Operating Voltage: 9 V DC
- Power Consumption: Nom. 70 mA / Max. 150 mA
- Housing Material: plastic
- Housing Surface: soft-touch
- Housing Colour: black
- Width: 80 mm
- Height: 42.5 mm
- Depth: 133 mm
- Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable
|
Overview
With Sennheiserʼs HDVD 800, sound is perfect. The HDVD 800 is able to connect with digital sources and is equipped with a high-quality Burr-Brown digital/analog converter (DAC) that converts digital audio data into analog signals with a resolution of 24 bits and a sampling rate of up to 192 kHz. This enables the HDVD 800 to transmit the entire frequency spectrum of high-end audio sources without any loss of frequencies.
In addition to the symmetrical inputs, the HDVD 800 also has an asymmetrical input socket; incoming signals are symmetrized before further processing takes place. Digital sources can be connected to the rear of the unit via an XLR (AES/EBU) input, optical and coaxial (S/PDIF) digital inputs or USB. All digital inputs accept signals up to 24 bit at 192 KHz*. Designed and manufactured in Germany, this high-end, solid-state amplifier harmonize perfectly and deliver an ultimate acoustic performance when paired with any of Sennheiserʼs audiophile headphones.
Features
D/A transducer for all common formats up to 24 bit / 192 kHz
D/A transducer can be used for CD and DVD players
AES/BU, S/PDIF, USB inputs
Symmetrical (XLR) and asymmetrical (RCA) analog inputs
Symmetrical output
Sockets for four sets of headphones (two of which symmetrical)
|
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
| LDHPA6 6-Channel Rackmount Headphone Amplifier
The LD Systems HPA 6 is a highly flexible 1U 19" rack format headphone amplifier with 6 fully independent channels and comprehensive features for a wide range of professional audio monitoring applications.
Each channel provides a 6.3 mm TRS headphone output on the front panel with level control, mono/stereo switching, discrete left/right muting and a 6.3 mm TRS Aux input with Main/Aux balance control for mixing in further signal sources. Four-segment LED meters permit visual output level monitoring, and two 6.3 mm TRS outputs per channel on the rear allow for connecting a total of 18 headphones.
The HPA 6\'s main section features a master level control with eight-segment LED metering and 6.3 mm TRS input to mix in an additional source with all channels. The rear panel provides the main stereo inputs on balanced XLR and 6.3 mm TRS connectors and stereo outputs for daisy chaining multiple units.
- Type: 6-channel
- Inputs: Main Input (Stereo), Direct In (Stereo), 6 x Aux In (Stereo)
- Input Connections: XLR and 6.3 mm jack L&R (Main Input, balanced), 6.3 mm stereo jack (Direct In), 6.3 mm stereo jack (Aux In)
- Input Impedance: 13 kOhm
- Line Outputs: Main Output (stereo, balanced)
- Line Output Connectors: XLR and 6.3 mm jack L&R
- Headphone Outputs: 6 x 3
- Headphone Output Connectors: 6.3 mm stereo jack
- Power Output: 6 x 125 mW
- Minimal Connected Impedance per Channel: 8 ohms
- Frequency Response: 20 Hz - 20.000 Hz
- Controls: Main Input Level, 6 x Input Mix Main/Aux, 6 x Headphone Level, 6 x Mono Switch, 6 x Mute L&R, Power
- Indicators: Main Input/Direct In Level Meter (8-segment LED chain), 6 x channel level meter (4-segment LED chain), 6 x mono LED, 6 x Mute L&R LEDs, Power LED
- Power Supply: IEC power socket
- Operating Voltage: 220 - 240 V AC, 50 - 60 Hz / 110 - 120 V AC, 50 - 60 Hz
- Power Consumption: 40 W
- Cabinet Material: metal
- Cabinet Surface: painted
- Width: 483 mm
- Height: 44 mm
- Depth: 217 mm
- Accessories (included): power cord
|
Info
Apogee Groove is the best portable USB DAC and headphone amp for listening to music on your Mac or PC. Groove takes the same high quality audio technology found in the worldʼs most prestigious recording studios and delivers it to your laptop. Connect Groove directly to your computer and connect your headphones or powered speakers directly to Groove. Itʼs that easy. Youʼll be amazed by the difference in sound quality. Highlights: USB 2.0 connection to Mac and PC Up to 24 bit / 192kHz audio ESS Sabre DAC Constant Current Drive?, Ultra-smooth frequency response for any headphones Quad Sum DAC?, 4 DACs per channel for highest dynamic range and lowest distortion Asynchronous clocking Max output level: 225mW into 30 Ohm Multi-color LEDs for status and level indication Powered by USB Top panel buttons for adjusting output level and muting Compact and portable (95mm H x 30mm W x 16mm T) Premium aluminum build quality Built in the USA Pricing to be announced
|
Reviews
There are no reviews yet.