Content |
Bass Station II is an analogue mono-synth based on the classic original Bass Station but re-worked for the 21st century. It has two filters, two oscillators plus a third sub-oscillator, patch save and a fully analogue effects section. Add a step sequencer, arpeggiator, full sized keys and a powerful modulation section and you have the makings of a synth that is built for bass, but capable of so much more.
Specifications Synth engine Oscillators - Osc 1
- Osc 2
- Sub Osc (3)
- Noise generator
Osc 1 & 2
Select between waveforms:
- sine
- triangle
- sawtooth
- square/variable pulse width
Features
- Sync 1 & 2
- Detune
- Octave range
- Pitch bend
- Pitch modulation from Mod Envelope and/or LFO 1
- Pulse width modulation from Mod Envelope and/or LFO 2
Sub Osc (3) which is tracked to Osc 1
Select independently between waveforms:
Features
- All modulation and tuning tracked to Osc 1
- Independent octave select
Mixer - Osc 1 level
- Osc 2 level
- Sub Osc level
- Noise generator level
- Ring modulation depth
- External signal level
Filter
Two filter types
- Acid type (diode ladder filter design)
- Classic type (derived from original Bass Station)
Features
- Cutoff
- Resonance
- Overdrive
- Filter frequency to Mod Envelope depth
- Filter frequency to LFO 2 depth
Select 'Classic' filter between:
- Low pass
- Band pass
- High pass
- 12dB slope
- 24dB slope
Envelopes
Two ADSR Envelopes (Attack/Decay/Sustain/Release)
- Amp Envelope
- Mod Envelope
- Combined control of both Envelopes
Select triggering mode between:
- Single trigger (holds envelope state when new note is played)
- Multi trigger (re-triggers with every new note played)
- Autoglide (engages portamento)
There is also a VCA limiter
LFO
Two LFOs each selectable between:
- Triangle
- Sawtooth
- Square
- Sample and hold
- Both LFOs independently adjustable between rate and delay time
- Key sync LFO 1 & 2
- LFO slew on LFO 1& 2 (low pass filter on the LFO waveform)
Effects - Distortion send
- Oscillator filter mod amount (FM effect created by Oscillator 2 modulating filter freq)
Step Sequencer/Arpeggiator
Arpeggiator
- Up to 32 different patterns
- Select between 1-4 octave range
- Swing function
- Select direction:
- up
- down
- up / down 1
- up / down 2
- As played
- Random
- Latch (hold the arpeggiator)
Step Sequencer
- Up to four sequences
- Assign one of 32 preset rhythms or create your own
- insert rests or legato (slide)
- Sequencer re-trigger function
Portamento - Adjust glide time
- Single trigger or re-trigger modes
- Integrate into step sequencer and arpeggiator
Hardware & controller assignment - 25 note synth-action keyboard
- Aftertouch can be assigned to modulate:
- Filter frequency
- LFO 1to Osc pitch
- Osc 2 speed
- Pitch wheel
- Modulation wheel can be assigned to:
- LFO 2 to filter frequency
- LFO 1 to Osc pitch
- Osc 2 pitch
- Octave up/ down buttons
- 64 factory presets
- 64 slots for user patches (and patch dump facility for storing more)
- Master volume dial
Inputs and Outputs - USB MIDI (for connecting & powering Bass Station II via host computer)
- Mono output on 1/4" TRS jack
- Headphone output on 1/4" TRS jack
- External input on 1/4" TRS jack
- Sustain pedal input on 1/4" TS jack
- MIDI IN / MIDI OUT ports on 5 pin din
- DC power input
- Switch between power off / DC powered / bus powered
Dimensions - 18" wide x 10.75" deep x 3" tall
| Not only on the outside did he gain weight, also his inner qualities have seen a remarkable step-up: besides the virtual-analog synthesis and the classic wavetables it now sports a whopping 60 megabytes of sample memory.
Just imagine to add a vocal-like noise spectrum to a typical Wavetable pad, spice-up a virtual-analog solo sound with a strong attack sample or just process any other sample with the countless oscillator and filter modulations.
Play your sound creations on the high-quality keyboard with velocity and aftertouch. Pitchbend and modulation wheel are at your disposal and, as a matter of course, you can connect a sustain pedal.
All this is packaged in a sleek metal enclosure with a big graphic display, endless stainless steel rotaries and an internal power supply.
And although it comes for an unbeatable price tag, we add something very special. It comes:
From Waldorf with Love!
Features:
- 60 Megabyte sample memory
- Class compliant USB MIDI for PC,Mac and Linux
- 16 part multimode
- maximum 25 voices polyphony
- highest quality standard keybed with 49 weighted keys and aftertouch
- Internal power supply
- Pitchbend and modulation wheel
- Virtual analog, wavetable, and sample based oscillators
- MIDI in/out
- Sturdy metal case
- Stainless steel rotary encoders
- Backlit 128x64 pixel LCD
- Over 1000 sounds
- 3 oscillators, 2 filters per voice
- Selectable drive curves
- Frequency modulation for oscillators and filters
- Three LFO, four envelopes per voice
- Extensive modulation capabilities
- Complex arpeggiator
- Powerful effects section
- weight: apprx 8,-- kgs
- weight in carton: apprx 9,5 kgs
|
Synth engine
• Up to 18 note polyphony (dynamic voicing)
• Mono-Timbral
Per patch:
• 3x oscillators
• 1x noise generator
• 2x ring modulators
Waveforms include:
• Square, sine, tri, sawtooth, pulse, 9x saw:pulse combinations.
• 20x digital waveforms
• 36x wavetables
Filtertypes:
2x filters per patch
• low pass no resonance 6dB per octave
• low pass 12dB
• low pass 18dB
• low pass 24dB
• band pass 6:6
• band pass 6:12
• band pass 12:6
• band pass 6:18
• band pass 18:6
• band pass 12:12
• high pass no resonance 6dB per octave
• high pass 12dB
• high pass 18dB
• high pass 24dB
Sources:
20 modulation slots per patch
• 6x envelope generators
• 3x LFOs.
• Aftertouch
• Velocity
• Key scaling/track
• Mod wheel
• Expression pedal
Total of 66 Destinations including:
• Oscillator pitch, pulse width, wavetable index, level and sync
• Filter cutoff, resonance, envelope settings
• Effects parameters and send levels
• Recursive modulation (modulating modulation sources themselves)
5 Effects slots per patch
• Distortion – up to 2 instances
• Compressor – up to 2 instances
• Chorus/Phase – up to 4 instances
• Delay – up to 2 instances
• Reverb – up to 2 instances
• Gator
• EQ
•12 band vocoder
• Arpeggiator – 33 patterns
• Chord function – lock up to 10 notes
• Patch storage up to 512 on hardware (ships with 300 factory patches)
Hardware
• 144 character LCD
• 8x detented touch sensitive encoders
• 1x large smooth encoder (with back-lit filter lock buttons)
• 1x large patch select/speed dial encoder
• 2x volume & monitor mix dials
• 39 LED lit/indicated buttons
• Pitch wheel (LED lit)
• Modulation wheel (LED lit)
• 37 note keyboard with velocity and aftertouch
• XLR dynamic mic input
• 2x ¼” jack inputs
• 2x ¼” jack outputs
• 2x ¼” jack aux outputs
• 1x ¼” jack headphone output
• SPDIF digital output on RCA connector
• Expression pedal on ¼” jack input
• Sustain pedal on ¼” jack input
• MIDI in/out/thru
• 12 volt power input
• USB port (UltraNova can be powered via USB)
• Kensington Lock port
|
MX49 is a 49 key music synthesizer which combines Motif XS sounds, USB Audio/MIDI connectivity and advanced DAW/VST controller features at a ground breaking level of affordability.
The new MX series combines Motif XS sounds, USB Audio/MIDI connectivity and advanced DAW/VST controller
features at a ground breaking level of affordability.
- Over 1000 sounds from the MOTIF series
- Equipped with VCM effects
- Easy Split /Layer Performance Mode for Instant Inspiration
- 16-Part Multi timbral and 128-note polyphony
- Extensive Hands-On controls for VSTs and DAWs
- Bi-directional USB Audio/MID interfacing
- A complete suite of music production software included
- A lightweight design with a quality Yamaha keyboard
- Complete analog and digital connectivity
The MX series contains more than 1000 Voices derived directly from the world famous Yamaha MOTIF XS series. From realistic acoustic sounds like piano, electric piano, strings and drums to complex 8-element synth sounds, the MX has all of your favorite Motif XS Voices right at your fingertips. The MX even has a streamlined interface for instant hands-on selection of all those great Voices. The newly designed category selection makes it easier than ever to find the Voice you need. You can even edit and store your own sounds right onboard.
MX synthesizers come equipped with VCM effects, which simulate vintage effectors at the circuit level. The sounds of the ʽ70s are brought back to life, through simulating the hard-to-find vintage sounds of equalizer, flanger, phaser, and wah effects introduced by the keyboard legends of the era.
Performance Mode on the Motifs has always been the place to find instant inspiration and the MX is no different. You can easily combine two Voices to play on the keyboard using the dedicated Split and Layer buttons each with their own intelligent arpeggiator and a dedicated Part for a drum track to create evocative Performances that feel like a whole band is playing. The 128 Performances on the MX are all user editable, but come programmed with the latest club friendly grooves.
Number of Keys: | 49 | Pitch Bend: | Yes | Modulation: | Yes | Tone Generating Technology: | AWM2 | Number of Voices: | 1,106 Normal Voices + 61 Drum Kits,GM: 128 Normal Voices + 1 Drum Kit,User: 128 Normal Voices+8Drum | Number of Polyphony: | 128 | Effects: | Reverb x 9, Chorus x 17, Insertion Effect x 48, Master EQ | USB Compatibility: | Yes | Display Type: | digit LED + 20 x 2 line character LCD (backlit) | MIDI: | In, Out | Ηeadphones Outputs: | Yes | Inputs/ Outputs: | Output (L/Mono/R), Foot Switch, LINE OUT, USB to Host/Device - See more at: http://www.nakas.gr/ecom | Dimensions (W x H x D): | 98.4 x 11.2 x 29.9 cm | Weight: | 3.8kg | Color: | Black | Accessories: | AC adaptor, Ownerʼs Manual, Online Manual CD-ROM x 1 |
|
Intuitive and ultra-powerful volca sequencer
A fun to use sequencer with superb improvisatory potential
The step sequencer is designed for ease of editing and to allow parts to be inserted or removed "on the fly." Use the 16 step keys to enter notes intuitively while maintaining visual confirmation of the timing of the notes in a measure. You can also record your performance in real time.
Up to ten of the sequence patterns you create can be stored in internal memory.
Motion sequencer records and plays back up to 11 parameters
The motion sequence function records your knob movements, letting you add time-varying change to the sound. This is a great way to polish your loops, and also lets you generate highly original live performances. The volca sample is able to record all knob movements that are related to sound editing. This allows sophisticated editing that had been impossible for hardware samplers of this category.
Parameters that can be used with Motion Sequence
・ Start Point (Playback start location)
・ Length (Playback length)
・ Hi Cut (Cutoff frequency)
・ Speed (Playback speed)
・ Pitch EG Int (Pitch EG depth)
・ Pitch EG Attack (Pitch EG attack time)
・ Pitch EG Decay (Pitch EG Decay time)
・ Amp Level
・ Pan
・ Amp EG Attack (Amp EG Attack time)
・ Amp EG Decay (Amp EG Decay time)
Keyboard
Multi touch Keyboard
Sampler
Type
PCM
Maximum Polyphony
8
Number of Samples
100 (User over writable)
Memory Size for Sample
4 MB, Maximum 65 seconds
Sampling Frequency
31.25 kHZ, 16 bit
Edit
Sample(Start Point, Length, Hi Cut), Pitch(Speed, EG Int, Attack,Decay), Amp(Level, Pan, Attack, Decay), Reverse On/Off
Effects
Digital Reverb
On/Off, Mix
Analogue Isolator
Bass, Treble
Sequencer
Number of Parts
10
Number of Steps
16
Number of Recording Patterns
10
Control
Motion Sequence, Active Step, Step Jump, Swing
Song
Maximum Number of Sequence
16
Number of Recording Songs
6
Connectors
Audio Output
Headphones (3.5mm stereo mini jack)
Sync
Sync In (3.5mm monaural mini jack, Maximum input level: 20V)
Sync Out(3.5mm monaural mini jack, Maximum Output level: 5V)
MIDI
MIDI IN
Power
Battery Life
Approximately 10 hours (using alkaline batteries)
Power Supply
AA alkaline battery × 6 or AA nickel-metal hydride battery × 6 Or AC adapter (DC 9V) (optional)
Others
Accessories
AA alkaline battery ×6 (for verifying operation), Cable
Options
AC adapter (DC 9V)
Dimensions
(W x D x H)
193 × 115 ×45 mm / 7.60” x 4.53” x 1.77”
Weight
372 g / 13.12 oz. (Excluding batteries)
|
Krome Music Workstation
On Stage. On the Go. On Top. Offering full-length, unlooped samples of every key for a spectacular piano sound, this new keyboard redefines your expectations for an instrument in this class. Taking its name from the Greek word meaning "color," Krome is the new standard for sonic excellence in a gigging musician\'s keyboard, providing a limitless palette of sound to bring vivid inspiration your music. Introducing the Krome Music Workstation. Product Highlights:
- The Korg workstation ideal for any style of piano playing
- Kronos-derived full length, unlooped piano and drum sounds, plus new electric pianos designed to shine on stage
- Electric pianos with eight-level velocity switching for unmatched expressive power
- Clear, intuitive control with Korg\'s exclusive 7-inch color TouchViewTM display
- Drums offering separately mixable direct and ambient sounds for studio-grade quality
- Drum Track plays back realistic, inspiring grooves at the touch of a button
- Expertly created, in-demand sounds including 640 Programs and 288 Combinations
- Powerful Effects with 5 Inserts, 2 Master, and 1 Total FX, plus per track/timbre EQ
- Distinctive aluminum panel design exudes a sense of quality
- USB connection to your computer, plus an SD Card slot for data storage
- You can use the Krome editor to edit sounds on your computer
- Available in 61, 73, and 88 key models.
In addition to Korg\'s well-proven workstation features, Krome features a carefully chosen selection of the top sounds available today for bread-and-butter keyboard instruments such as piano and electric piano, as well as vital and dynamic drum kits, giving you the best of the basics. These highly usable piano, electric piano, and drum sounds by themselves set Krome apart from any other keyboard in its class. With sound quality and features normally found in much more expensive instruments, Krome aspires to set a whole new value standard, and become a unique and irreplaceable partner for real-world musicians.
Specifications
Keyboard
Krome 61: Semi-weighted keyboard
*velocity-sensitive supported, after touch is not supported
*Standard C2-C7 (transposable in the range [C1...C6]-[C3...C8])
Krome 73: Semi-weighted keyboard
*velocity-sensitive supported, after touch is not supported
*Standard C1-C7 (transposable in the range [C0...C6]-[C2...C8])
Krome 88: NH keyboard (Natural Weighted Hammer Action] keyboard
*velocity sensitive is supported, after touch is not supported
*Standard A0-C8 (transposable in the range [A-1...C7]-[A1...C9]
*The NH keyboard reproduces the touch of an acoustic piano, with a heavier feel in the low register and a lighter feel in the upper register.
System
EDS-X (Enhanced Definition Synthesis-eXpanded)
Sounds
Maximum Polyphony:
120 voices (120 Oscillators) / Single Mode
60 voices (120 Oscillators) / Double Mode
*The maximum simultaneous voice polyphony will vary depending on oscillator settings such as stereo multisamples and velocity crossfading.
PCM Memory:
3.8 GB, 48kHz/16-bit linear equivalent
583 Multisamples (Including 12 Stereo multisamples)
2,080 Drumsamples (Including 474 Stereo Drumsamples)
Program:
Oscillator
OSC1 (Single); OSC1 + 2 (Double): Stereo multisamples are supported
8 velocity zones per oscillator with switching, crossfades and layers
Filters
Four types of filter routing (single, serial, parallel, 24 dB)
Two multi-mode filters per oscillator (low pass, high pass, band pass, band reject)
Driver
Per-voice nonlinear driver and low boost
EQ
Three bands, with sweepable mid
Modulation
For each oscillator: two envelope generators (Filter & Amp)
Two LFOs
Two key tracking generators (Filter & Amp)
Two AMS mixers
Pitch EG
Common LFO
Two common key tracking generators
Combination:
Timbres: 16 maximum, each with split/layer/velocity switching with crossfading, plus modifications via Tone
Adjust function
MIDI Controller Functionality: Customizable MIDI channel and Internal/External/Both settings per timbre
Master Keyboard Functionality
It\'s available for controlling external MIDI devices
Drum Kit:
Stereo and mono drum samples
8 velocity zones switch (crossfades and layers)
Sounds:
Program: 640 preload, 768 total locations
Combi: 288 preload, 512 total locations
Drumkits: 32 preload, 48 total locations
The number of Combination / Program / Drum Kit:
User: 512 Combination (288 Preload)
User: 768 Program (640 Preload)
User: 48 Drum Kit (32 Preload)
Preset: 256 GM2 Program + 9 GM2 Drums Program
Effects
Insert Effects:
5 Insert Effects (stereo in/out)
2 Master Effects (stereo in/out)
1 Total Effect (stereo in/out)
Timbre / Track EQ:
3-band EQ per timbre/track
Effect Types:
193, useable as Insert, Master, or Total effects. Note that a double-size effect cannot be used as a total effect.
Modulation:
Dynamic Modulation, 2 Common LFO
Effects Control Busses:
Stereo sidechain (Limiter, Gate, Vocoder, etc)
Effect Preset:
32 preset per effect
Polyphonic Arpeggiator
Program Mode:
Single polyphonic arpeggiator
Combination, Sequencer Mode:
Dual polyphonic arpeggiators
Number of pattern:
900 preload, 1028 total locations
5 preset arpeggio patterns
Drum Track
637 preload, 1000 total locations
Configurable Trigger Mode/Sync/Zone
Sequencer
Tracks:
16 MIDI tracks + 1 master track
Number of Songs:
128 Songs
Resolution:
1/480 PPQ
Tempo:
40.00- 300.00 (1/100 BPM resolution)
Maximum memory:
210,000 MIDI events
Template Song:
16 preset / 16 user template songs
Cue List function:
20 Cue Lists
99 steps
Pattern:
605 Preset / 100 User patterns
RPPR (Realtime Pattern Play and Recording):
1 pattern set per song
Format:
KORG (KROME) format, SMF format 0 and 1
Media
Load, Save, Utility, data filer functionality (Save and Load MIDI System Exclusive Data)
Controllers
*Joystick, SW [1], SW [2]
*Realtime Control
[SELECT] Switch:
REALTIME CONTROL (TONE, USER), ARP
4 Knobs;
REALTIME CONTROL: Real-time Modulation, Arpeggio control
*Drum Track
[DRUM TRACK] Switch On/Off
*Arpeggiator
[ARP] Switch On/Off
User Interface
Display:
TouchView(tm) Graphical User Interface
7-inch color TFT LCD, 800 x 480 pixels
Onboard LCD brightness control
Mode Switch:
[COMBI], [PROG], [SEQ], [GLOBAL], [MEDIA] switch
VALUE controller:
[VALUE] Dial, [INC], [DEC] Switch, 10 key block ([0] - [9], [-], [.], [ENTER], [COMPARE])
BANK Switch:
[A], [B], [C], [D], [E], [F] switch (in Combination mode, [A], [B], [C], [D] switch are available)
SEQUENCER switch:
[PAUSE], [REW], [FF], [LOCATE], [REC], [START / STOP]
TEMPO:
[TEMPO] knob, [TAP] switch
Others:
[PAGE] switch, [WRITE] switch, [EXIT] switch, [VOLUME] knob, Contrast knob
Outputs
AUDIO OUTPUT (L / MONO, R):
6.3mm (Mono) Phone jack, Unbalanced
Output Impedance: 1100Ohm, 550Ohm with Mono output
Maximum level: +16.0 [dBu], Load Impedance: more than 10Ohm.
Headphone Output:
3.5mmStereo phone jack
Output Impedance: 33Ohm
Maximum level: 60 + 60mW with 33Ohm load
Control Input
DAMPER pedal (Half Damper supported)
ASSIGNABLE SWITCH
ASSIGNABLE PEDAL
MIDI
IN/OUT
USB
USB-MIDI Interface (TYPE B) x 1
SD Card Slot
Max: 2 GB / SD memory card
Max: 32 GB/ SDHC memory card
Note: SDXC memory cards are not supported.
Power
Power supply (DC12V 3.5A), POWER switch
Dimensions (W x D x H)
KROME-61 = 40.43 x 12.32 x 3.66 inches / 1,027 × 313 × 93 mm
KROME-73 = 46.89 x 12.32 x 3.66 inches / 1,191 × 313 × 93 mm
KROME-88 = 57.01 x 15.08 x 5.16 inches / 1,448 × 383 × 131 mm
Weight
KROME-61 = 15.87 lbs. / 7.2 kg
KROME-73 = 18.08 lbs. / 8.2 kg
KROME-88 = 32.41 lbs. / 14.7 kg
Power Consumption
13 W
Accessories
AC Adapter
Quick Start Guide
Accessory Disc (Operation Guide PDF, Parameter Guide PDF, Video Manual)
Option
XVP-10: Expression/Volume pedal
EXP-2: Foot Controller
DS-1H: Damper Pedal
PS-1, PS-3: Pedal Switch
PC System Requirements for Krome Editor/Plug-In Editor
Windows
OS:
Windows Vista SP2 and later (32- and 64-bit, all editions),
Windows 7 (all editions, including 64-bit)
Computer:
USB port required
Macintosh
OS:
Mac OS X 10.4.11 or later
Computer:
USB port required
PC System Requirements for Krome Editor/Plug-In Editor
Windows
OS:
Windows Vista SP2 and later (32- and 64-bit, all editions),
Windows 7 (all editions, including 64-bit)
CPU:
Intel Pentium 4/ Greather than 1 gHz, later Core Duo recommended.
Memory:
More than 512MB (Greater than 1 GB recommended)
Monitor:
1,024x768, at least 16-bit color
Others:
Computer with USB port, running Windows 7, Windows XP, or Windows Vista
Macintosh
OS:
Mac OS X 10.5 or later (32-bit and 64-bit kernel modes supported)
Note: This plug-in is not 64-bit.
CPU:
Intel Mac supported
Later Core Duo recommended
Memory:
More than 512MB (at least 1 GB recommended)
Monitor:
1,024x768, at least 32,000 colors
Others:
Apple Macintosh computer with USB port, running Mac OS X.
*Krome Plug-In Editor supports VST/RTAS in Windows, VST/ Audio Unit/RTAS in Macintosh.
*Only a single instance of the Krome Editor or Krome Plug-In Editor can be used at once.
*All other product and company names are trademarks or registered trademarks of their respective holders.
*Specifications and appearance are subject to change without notice for improvement.
|
Reviews
There are no reviews yet.