Content |
- Three-channel tabletop mixer
- Inputs: two phono/line switchable (RCA), four line (RCA), mic (1/4“)
- Outputs: Master (RCA), Record (RCA), headphone (1/4" stereo)
- Steep three-band EQ/rotary kills on each channel
- Microphone input with EQ
- Six-segment LED display for monitoring signal strength
- Toggle for master and PFL metering
- Replaceable crossfader with reverse and slope controls
Inputs:
- Line: 10K ohm input impedance; 80mV RMS sensitivity for 0dB output
- Mic: 600 ohm input impedance unbalanced; 1.5mV RMS sensitivity for 0dB output; 400mV RMS max input
- Phono: 47k ohm input impedance; 1.3mV RMS sensitivity @ 1kHz for 0dB output
Outputs:
- Line: 7V RMS max
- Headphone: 0.5W into 47ohm
Signal to Noise Ratio (maximum output JIS-A weighted):
- Line: Better than 100dB
- Mic: Better than 95dB
- Phono: Better than 85dB
Distortion: Less than 0.05%
Frequency response:
- Line: 20 – 20,000 Hz ±0.5dB
- Mic: 20 – 15,000 Hz ±0.5dB
- Phono: ±1dB; -3dB attenuation at 20 Hz to reduce rumble and feedback
Channel Equalizer:
- Bass: +12 / -35dB at 20 Hz
- Mid: +12 / -25dB at 1.3 kHz
- Treble: +12 / -20dB at 15 kHz
Channel fader kill: Better than 90dB at 1 kHz
Crossfader kill: Better than 75dB
Crosstalk: Better than 80dB at 1 kHz | PowerMate 1000
SPECIFICATIONS
Order No.
F01U131113 (DC-PM1000-3-UNIV)
Channels (Mono + Stereo)
6 + 4
Auxiliaries (MON, FX, AUX)
2 Pre, 2 Post, 2 Pre/Post switchable
Maximum Midband Output Power,1 kHz, THD=1%, Dual Channel
into 2.66 Ohms
2 x 1350 W
into 4 Ohms
2 x 1000 W
into 8 Ohms
2 x 600 W
Rated Output Power,THD=0.1%, Single Channel
into 4 Ohms
2 x 900 W
into 8 Ohms
2 x 450 W
Maximum Output Voltage of power amplifier, no load
74 Vrms
THD at 1kHz, MBW=80kHz
MIC input to Master A L/R output, +16 dBu, typical
< 0.005%
POWER AMP INPUTS to Speaker L/R output
< 0.075%
DIM 30, power amplifier, 60Hz, 7kHz
< 0.05%
IMD-SMPTE, power amplifier, 60Hz, 7 kHz
< 0.015% CMRR, MIC input, 1 kHz > 80 dB
Equivalent Input Noise, MIC Input, A-weighted, 150 Ω
-130 dBu
Signal/Noise-Ratio, power amplifier, A-weighted, 4 Ohms
105 dB
Output Stage Topology, amplifier
Class D
Equalization
LO Shelving
+/- 15 dB / 60 Hz
MID Peaking, mono inputs
+/- 15 dB / 100 Hz .. 8 kHz
MID Peaking, stereo inputs
+/- 12 dB / 2.4 kHz
HI Shelving
+/- 15 dB / 12 kHz
Master EQ, 11-band (63, 125, 250, 400, 1k, 1.6k, 2.5k, 4k, 6.3k, 12k Hz)
+/- 10 dB / Q = 1.5-2.5
Filter
LO-CUT, mono inputs
f=80 Hz, 18 dB/oct
VOICE FILTER, mono inputs
FEEDBACK FILTER, MON1/2
70 Hz .. 7 kHz, Notch, -9 dB
Speaker Processing
LPN, switchable
Display
High Contrast OLED
Effects |
A professional mixer offering two digital effect units and a 2 x 300 watts power amplifier to be used in entertainment and multimedia applications. Whether it is being used as mobile DJ-mixer, by a rental company, in a clubhouse, a hotel, a club / bistro, or in the party cellar at home: the comprehensive set of features and professional audio quality of the MP-7 Entertainment System also solves your sound reinforcement problem.
Maximum Midband Output Power, 1 kHz, THD = 1%: - into 4 ohms 2 x 340 W into 8 ohms 2 x 200 W Rated Output Power, 20Hz… 20 kHz, THD =0.2%: - into 4 ohms 2 x 300 W into 8 ohms 2 x 150 W Maximum Output Voltage of the power amplifier, no load THD @ 1 kHz, MBW=80kHz 43 Vrms MIC input to Main L/R output, +16 dBu 90 dB Channel seperation > 70 dB Input Sensitivity, all level controls in max. position: - MIC input -74 dBu (155µV) Line Input (Mono) -54 dBu (1.55 mV) CD/MD Line Input (Stereo) -24 dBu (49 mV) Phone Input (Stereo) -61.5 dBu (652 µV) Power Amplifier Input +6 dBu (1.55 V) Maximum Level, mixing desk: - MIC inputs +11 dBu Line inputs +30 dBu All other inputs +20 dBu Record Send output +14 dBu All other outputs +20 dBu Input Impedances: - MIC 1.8 kohms All other inputs > 10 kohms Output Impedances: - Record Send 1 kohms Phones 47 ohms All other outputs 75 ohms Equivalent Input Noise, MIC Input, A-weighted 150 ohms -130 dBu Noise, Channel inputs to Main L/R outputs, A-weighted: - Master fader down -104 dBu Master fader 0 dB, Channel fader down -91 dBu Master fader 0 dB, Channel fader 0 dB, Channel gain unity -84 dBu Signal/Noise-Ratio, power amplifier, A-weighted 105 dB Equalization STEREO: - LO Shelving +9/-30 dB / 60 Hz MID Peaking +9/-30 dB / 2.4 kHz HI Shelving +9/-30 dB / 12 kHz Equalization MIC: - LO Shelving ±15 dB / 60 Hz MID Peaking ±12 dB / 2.4 kHz HI Shelving ±15 dB / 12 kHz Master EQ, 2x7-band, Stereo ±10 dB Phantom Power, all MIC Inputs +24V dc Lamp +12V dc Power Requirements, factory preset, 50Hz....60Hz 100V/120V/230V/240V Power Consumption at 1/8 maximum output power 4 ohms 450 W Dimensions, (WxHxD), mm 455,5 x 175,8 x 340.6 Weight, including lid 13 kg Optional Rack-Mount-Kit MP7
| Since 1984 the SCLAT mixing desks have been rocking thousands of class venues around the world, serving the most demanding technicians, the most creative pro-Djs and the most exciting dance floors.
Behind the renowned experience of ECLER Laboratories, the SCLAT 200vs keeps combining all the requirements technicians demand regarding features and operating safety together with the inventive functionality Professional DJs demand from a high-end mixing desk.
Designed to optimize the best high-end club P.A.s, featured to fit any studio recording standard, built to withstand the most demanding mobile touring set-ups, the SCLAT 200vs is probably the best quality Audio Mixing Desk presently available in the Industry.
Superior effects processor
Remix live...
Built-in processor with double DSP featuring 2 manual filters and 10 effects with BPM synchronization. Includes a DRY/WET crossfader taking your effects control to the next level: activate and deactivate, fade in to the level of your choice… Allows routing every single channel to the module independently. Features control of TIME and PARAMETER and a friendly user selectable panel. Effects consists of LFO Filter, Low Pass Filter, High Pass Filter, Delay, Reverb, Flanger, Phaser, Vocoder, Pitch Shifter, Echo Reverb, Filtered Echo and Flanger Echo.
Midi out
Control you favorite devices...
The module includes a MIDI output and features start and stop commands to activate and deactivate your devices and a clock to adjust the tempo.
Edi:lab software
Expand your creativity...
The built-in effect processor is reprogramable in real-time with the edi:lab software (included). The user can load a new effect set-up in the SCLAT mixer and play it stand-alone without any need of the computer. An effect library is available in the edi:lab software in order to save the different user set-ups. |
- 6 input channels
- MIC (XLR3) inputs on channels 1 and 2
- MIC (JACK ¼”) / stereo LINE (RCA) in channels 3 and 4. Input signal pushbutton selector (MIC/LINE) on back panel
- Stereo LINE (RCA) on channels 5 and 6
- Input signal gain level control (accessible only with screwdriver)
- Each channel features signal present (SP) and CLIP indicators
- General phantom power switch located on back panel. Independent internal phantom power assignment to any MIC input
- Triple tone control (accessible only with screwdriver)
- 2 main stereo OUTPUTS (XLR3) with independent volume control
- 3 LED OUTPUT level meter
- Input channels can be routed to any main output (A,B) or both
- 2 additional stereo REC outputs (REC1, REC2)
- Mono mode selector in outputs A and B
- Headphones monitoring of selected output (A or B)
- Integrated, internally configurable talkover. Affects OUT A and REC A
- Remote MUTE function (PHOENIX) allows linking to external fire detection centrals
- TALKOVER function fully configurable to –20dB or –30dB that affects boths outputs A and REC A
The SAM mixer series has been specially designed for all public address and communication systems requiring a minimum risk of unwanted external manipulation.
Frequently used controls are easily accessible. Specific adjustments remain only accessible by the installer for precise and permanent settings.
SAM SERIES are very easy to use, even for non-technical users. All this is packed into a compact, 1 unit high, 19'' rack unit.
SAM series general KEY features
- Universal 1 RU, 19” installation mixers
- Excellent frequency response
- Balanced MIC and stereo LINE inputs and main outputs
- Reliable proprietary power supply
- Ideal for any application requiring a trouble free mixer
| • Bluetooth playback
• Talk over function
• VU channel indication
• MP3 / Phone input selector
Core Beat is the little brother of the Core MIX-3 USB. It has 6 Line inputs, a microphone input and a Bluetooth playback module. The Bluetooth playback module makes it possible to mix your connected players with wireless devices such as a smartphones or tablets. It also has an input that can be switched between line and MP3 level. The MP3 level adjusts the input sensitivity into the correct level for MP3 players, smartphones or tablets. Now you can playback your MP3 devices directly without signal loss. It's built with high quality components to get the best performance and has a separate fader board for easy maintenance The Core Beat has all functionality you need to get your DJ career started. It is equipped with VU indication on each channel, selectable cross-fader curves, a talk over, outputs for both master and booth and with -26dB tone control you will cut any beat you like. Let the Beat rock!
Specifications Inputs channels: 1 x Microphone, combo XLR/Jack
6 x Line, RCA
1 x Bluetooth
Output channels: 1 x Record, RCA
1 x Booth, RCA
1 x Master unbalanced, RCA
1 x Headphones, TRS 6.3mm Jack
Channel EQ range: -26dB / +12dB
Microphone EQ range: -12dB / +12dB
Frequency response: 20Hz -20Khz
Mic S/N Ratio: > 80dB
Line S/N Ratio: > 85dB
Dimensions: 247 x 331 x 84 (WxDxH)
Power input: AC15V/750mA (Adapter included)
Power consumption: 8W
Weight: 4,1 Kg |
Reviews
There are no reviews yet.